Gemini Appliance IM-2400H Bedienungsanleitung

Quick Start Guide

Version 2.5 | Hardware Version 4

CONTENTS

1. Introduction

1.1 Gemini Appliance Model Identification

1.1.1 IM-2400H / IM-2600H Front Panel

1.1.2 IM-2400H / IM-2600H Back Panel

1.1.3 SS-1000S / SM-1000S / SL-1000S / IS-1100D / IM-1100H / IL-1200H / IM-1040S /

IS-1200S / IM-1200S / IL-1200S Front Panel

1.1.4 SS-1000S / SM-1000S / SL-1000S / IS-1100D / IM-1100H / IL-1200H / IM-1040S /

IS-1200S / IM-1200S / IL-1200S Back Panel

1.1.5 G1000 / IB-1050D Front Panel

1.1.6 G1000 / IB-1050D Rear Panel

2. Getting Started

2.1 Prerequisites

2.2 Power On

2.3 Appliance Log In

2.4 Network Configuration

2.4.1 DHCP Setup

2.4.2 Manual Network Setup

3. Gemini Enterprise: Manage

3.1 Activation

3.1.1 EULA

3.1.2 Localization

3.1.3 Select License Option

3.1.3.1 Activate Enterprise Edition License

3.1.3.1.1 License Request and Application

3.1.3.1.2 License Server Validation

3.1.4 Provisioning

3.1.4.1 Bulk Provisioning

3.1.4.1.1 Appliance Discovery

3.1.4.1.2 Network Settings

3.1.4.1.3 Hostname

3.1.4.1.4 Change Admin Password

3.1.4.1.5 Connect to LDAP

3.1.4.1.6 SSH Authentication

3.1.4.1.7 Summary

3.1.4.2 Stand-Alone Provisioning - Join Cluster

3.1.4.3 Stand-Alone Provisioning - Change Admin Password

3.1.4.4 Stand-Alone Provisioning - Success

3.1.5 Welcome to Gemini Enterprise: Manage

3.1.6 Adjust Storage Plan

3.1.7 Install Featured Platforms

4. Additional Support

1. Introduction

1.1 Gemini Appliance Model Identification

1.1.1 IM-2400H / IM-2600H Front Panel

Figure 1. IM-2400H / IM-2600H Front-Panel

(1) Power Button

(2) VGA D-Sub

1.1.2 IM-2400H / IM-2600H Back Panel

Figure 2. IM-2400H / IM-2600H Rear Panel

(1) Ethernet Port 1

(2) Ethernet Port 2

(3) Ethernet Port 3

(4) Ethernet Port 4

(5) Spare Disk (IM-2600H)

1.1.3 SS-1000S / SM-1000S / SL-1000S / IS-1100D / IM-1100H /

IL-1200H / IM-1040S / IS-1200S / IM-1200S / IL-1200S Front

Panel

Figure 3. SS-1000S / SM-1000S / SL-1000S / IS-1100D / IM-1100H / IL-1200H / IM-1040S / IS-1200S /

IM-1200S / IL-1200S Front-Panel

(1) Power Button

(2) VGA D-Sub

1.1.4 SS-1000S / SM-1000S / SL-1000S / IS-1100D / IM-1100H /

IL-1200H / IM-1040S / IS-1200S / IM-1200S / IL-1200S Back

Panel

Figure 4. SS-1000S / SM-1000S / SL-1000S / IS-1100D / IM-1100H / IL-1200H / IM-1040S / IS-1200S /

IM-1200S / IL-1200S Rear Panel

(1) Ethernet Port 1

(2) Ethernet Port 2

(3) Ethernet Port 3

(4) Ethernet Port 4

1.1.5 G1000 / IB-1050D Front Panel

Figure 5. G1000 / IB-1050D Front Panel

(1) Power Button

(2) VGA D-Sub

1.1.6 G1000 / IB-1050D Rear Panel

Figure 6. G1000 / IB-1050D Series Panel

(1) Ethernet Port 1

(2) Ethernet Port 2

(3) Ethernet Port 3

(4) Ethernet Port 4

 

2. Getting Started

2.1 Prerequisites

a) An ethernet cable and available ethernet switch connection

b) One IP address for Gemini appliance ethernet port 1 (address, netmask and

gateway are required for manual configuration. DHCP is supported)

c) A client PC which is able to access to the Gemini appliance IP address defined

above.

d) Google Chrome browser is recommended.

e) (optional) Access to the Splunk Enterprise installation tarball

(splunk-*.*.*-*-Linux-x86_64.tgz).

f) (optional) Internet access and FQDN of this appliance are required for Cloudera

CDH installation.

2.2 Power On

a) Plug and connect the power cables to the appliance’spower supply unit

b) Connect a VGA monitor and USB keyboard

c) Connect the primary ethernet cable to ethernet port 1

d) Press front panel Power Button (A).

The button may need to be pressed twice the first time the appliance is turned on.

2.3 Appliance Log In

If the ‘login’ prompt is not visible on the connected monitor, press ‘enter’ on the

keyboard a few times. The login prompt should appear.

For initial setup, log into the appliance as user sbox with the default password “facing

jet function drive” . The setup flow will require the user to choose a new secure

password before configuration can continue. The password can always be changed

once the appliance is configured.

2.4 Network Configuration

2.4.1 DHCP Setup

The use of DHCP for IP assignment is not recommended. If you choose to utilize a

DHCP assigned address, simply let the appliance boot up and an address will be

assigned. To verify the address, log onto the appliance and run the “ip addr”

command.

[sbox@sboxnode1 ~]$ ip addr

1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN

link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00

inet 127.0.0.1/8 scope host lo

valid_lft forever preferred_lft forever

inet6 ::1/128 scope host

valid_lft forever preferred_lft forever

2: nic0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen

1000

link/ether 08:00:27:9e:96:c0 brd ff:ff:ff:ff:ff:ff

inet 192.168.1.100/24 brd 192.168.1.255 scope global dynamic nic0

valid_lft 68091sec preferred_lft 68091sec

After running “ip addr”, locate the output stanza for “nic0”. Locate the assigned IP

address in the string following the “inet” tag. This is the ethernet address assigned to

to the primary ethernet port. Additional network ports can be assigned using the

Gemini Enterprise: Manage.

2.4.2 Manual Network Setup

The first ethernet port must be configured before the appliance can be managed. To

do so, log onto the appliance as detailed in step 2.3 and use the following command to

complete the network setting if there’s no DHCP server for IP address assignment:

sbox network -nic <Network interface name> -ip <IP address> -netmask

<Netmask> -gateway <Gateway IP>

For example:

sbox network -nic nic0 -ip 192.168.1.100 -netmask 255.255.255.0 -gateway

192.168.1.1

will configure the network settings exactly the same with assigned by DHCP in step

2.4.1. This IP address will be used for the remainder of the configuration. This is

important to configure network settings correctly so the appliance can be accessed.

If there’re more than one ethernet ports connected, you may use the same command

to complete the rest settings.



3. Gemini Enterprise: Manage

Final configuration of the appliance is completed using the Manage web console.

Using a supported web browser, navigate to:

https://<IP address from prior step>

A security warning or message may be displayed. This is expected and does not

indicate a problem. Depending on your browser you may have to choose “proceed

anyway” or “continue” for the page to load.

3.1 Activation

3.1.1 EULA

Upon the first visit to Manage, the End User Software License Agreement is shown.

After reading the terms, choose Accept to advance to the next screen.

3.1.2 Localization

Manage supports multiple languages and setting a preferred language adjusts the

entire user experience accordingly. .

If the hostname and timezone settings were skipped in previous basic configurations,

this step provides an opportunity to configure them.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Arista

Arista CCA-ETM-Q12 Bedienungsanleitung