Gemtek Systems T-316 Bedienungsanleitung

Wi-Fi Ethernet Smart Client

T-316

User’s Manual

Revision1.0

T-316

User’s Manual

Gemtek Systems reserves the right to change specifications without prior notice.

While the information in this manual has been compiled with great care, it may not be deemed an assurance of product

characteristics. Gemtek Systems shall be liable only to the degree specified in the terms of sale and delivery.

The reproduction and distribution of the documentation and software supplied with this product and the use of its contents is

subject to written authorization from Gemtek Systems.

The product described in this book is a licensed product of Gemtek Systems, Inc.

Microsoft, Windows 95, Windows 98, Windows Millennium, Windows NT, Windows 2000, Windows XP, and MS-DOS are

registered trademarks of the Microsoft Corporation.

Novell is a registered trademark of the Novell,Inc.

MacOS is a registered trademark of Apple Computer, Inc.

Java is a trademark of Sun Microsystems, Inc.

Wi-Fi is a registered trademark of Wireless Ethernet Compatibility Alliance.

All other brand and product names are trademarks or registered trademarks of their respective holders.

Notice

Trademarks

Contents

1. Introduction..................................................................................................4

2. Installation....................................................................................................5

3. Configuring the Wireless Ethernet Client .....................................................6

4. Contents of Web Interface ...........................................................................7

4.1 Info Page ............................................................................................7

4.2 Wireless Settings................................................................................8

4.3 Bridging Table.....................................................................................9

4.4 IP Setting ..........................................................................................10

4.5 Administration ................................................................................... 11

4.6 Security.............................................................................................12

5. Troubleshooting.........................................................................................14

6. Technical Specification of Wireless Ethernet Client...................................15

1. Introduction

Thank you for purchasing the T316 Wireless Ethernet Smart Client.

This manual will assist you with the installation procedure.

The package you have received contains the following items:

• 11Mbps Wireless Ethernet Client

• Cat.5 Ethernet with USB power extractor cable

• CD

Note: if anything is missing, please contact your vendor.

T316 allows for one Ethernet-enabled device (e.g., Windows/MAC/Linux/UNIX

Desktop PC or laptop) to be instantly connected to an existing 802.11b wireless

network. Taking full advantage of the integrated Web server capability, T316 is

performed through a simple Web browser user interface for easy configuration.

Besides laptop or desktop environment, T316 is also the ideal solution to make

other network device such as network printer or camera becomes a wireless

station.

2. Installation

1. Mount T316 Wireless Ethernet Smart Client to your device firmly.

2. Insert the power connector.

3. Attach the Wireless Ethernet Client to the Ethernet network using a UTP

Ethernet cable.

At the front of the Wireless Ethernet Client you will see three LEDs.

If all go well, the Power LED is red and the LINK and ACT LED will be blinking

whenever there is traffic on the wired and wireless networks respectively.

Reset the Wireless Ethernet Client

If you press the reset button for more than four seconds, the Wireless Ethernet

Client will be reset to the default factory settings. All changes you made to the

configuration will be lost.

1. Insert one end of a paper clip into the hole of reset button and keep it pressed

for more than four seconds. LINK LED will be blinking during the process.

2. Release the reset button after ACT LED goes off. All settings will be deleted and

back to the default. You can refer to this manual and reconfigure the Wireless

Ethernet Client by yourself.

3 Configuring the Wireless Ethernet Client

The Wireless Ethernet Client is a ready-to-use device. It is delivered with default

settings that allow you to have access to it without configuring it. When this

message window pops up, press OK to access web configuration page. No user

name and password needed.

You can configure the Wireless Ethernet Client via a JavaScript-enabled

web-browser such as Internet Explorer 4.0 or higher, or Netscape Navigator 4.0 or

higher.

Factory Default Settings for the Wireless Ethernet Client

SSID default

Channel 6

Transmission rates Auto

WEP enable No

IP Address mode Static

IP Address 192.168.5.99

Subnet mask 255.255.0.0

User Name Blank

Administrator or password Blank (no password needed)

The computer that you are using for initial configuration must have an IP Address

within the same range as the IP Address of the Wireless Ethernet Client.

The Wireless Ethernet Client has a default IP Address of 192.168.5.99 with

a subnet mask of 255.255.0.0

4. Contents of Web Interface

4.1 Info Page

The Info window displays the current setup status of the Wireless Ethernet Client.

Communication Quality

Specifies the Communications Quality of the Basic Service Set to which the station

is currently connected. The value for the field of this record is based on signal level

and noise level measurements.

Firmware Version

This indicates the Wireless Ethernet Client’s firmware version.

Current setting of IP Address

It shows IP address of the wireless Ethernet Client.

Non-IP MAC Address

The MAC Address of Ethernet port that bridges to Wireless Ethernet Client.

4.2 Wireless Settings

The settings of the wireless device are displayed here, and you can edit some of

these settings.

Operating Mode: Infrastructure

This is the default setting. Switch to Ad-Hoc mode when communicating to another

client device without the presence of Access Point.

SSID

The SSID is also known as Service Set ID. This is the name of your wireless

network. Only Wireless Ethernet Clients and clients that share the same SSID are

able to communicate with each other.

P.S. You can leave this blank and then reboot it to scan the environment

You will see what AP available around you at Info page.

Channel

This is the channel that the Wireless Ethernet Client uses to transmit and receive

data. The channel that you select here is restricted to the channels that can be

used within your regulatory domain.

TX rate

The transmit rate identifies the preferred data transmission speed of the Wireless

Ethernet Client. Transmissions at faster rates allow for higher data throughput and

quicker network response times. However, transmissions at lower rates are usually

more reliable and cover longer distances than the higher rates.

Access Point Density

When connecting to the Access Point, it is generally necessary to specify an

Access Point Density. This provides some control over handoff of clients during

roaming between Access Points. Three values, Low, Medium, and High

4.3 Bridging Table

The table lists your device that is bridging with the Wireless Ethernet Client.

4.4 IP Setting

Static

Select Static (recommended) to assign the IP, Subnet Mask and Gateway

Address.

DHCP

If the Wireless Ethernet Client is part of a network with a DHCP server, the DHCP

server will assign the IP settings to the Wireless Ethernet Client automatically.

(This is not recommended because a DHCP-assigned IP Address will change

frequently, making the Wireless Ethernet Client impossible to configure.)

Device Name

Assign the name of the Wireless Ethernet Client.

Allow Upgrade Uploads

Select this checkbox when performing firmware upgrade.

Andere Handbücher für T-316

Inhaltsverzeichnis

Andere Gemtek Systems Netzwerk-Router Handbücher

Gemtek Systems

Gemtek Systems CPE7000 Bedienungsanleitung

Gemtek Systems

Gemtek Systems WLTFQT141GN Bedienungsanleitung

Gemtek Systems

Gemtek Systems BC-4GMCPGa Bedienungsanleitung

Gemtek Systems

Gemtek Systems R921212G Bedienungsanleitung

Gemtek Systems

Gemtek Systems WLTFQR-121 Bedienungsanleitung

Gemtek Systems

Gemtek Systems P-380 Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise