General Pipe Cleaners D-25 Handy Bedienungsanleitung

General D-25 Handy™

Operating Instructions

For 1” through 2 ” lines

This tool is designed to give you years

of trouble-free, profitable service. How-

ever, no machine is better than its opera-

tor.

Read, understand and follow all safety

warnings and instructions provided with

the product. Failure to follow the warnings

and instructions may result in electric

shock and/or serious injury. Save all warn-

ings and instructions for future reference.

SAVE THESE INSTRUCTIONS!

 Pour français voir la page 5

 Para ver el español vea la paginá 9

These instructions are intended to

familiarize all personnel with the safe

operation and maintenance

procedures for the D-25 Handy.

WARNING! Failure to follow all instructions

listed below may result in electric shock, fire

and/or serious personal injury. Replacement

manuals are available upon request at no

charge, or may be downloaded from our web-

site, www.drainbrain.com.

If you have any questions or problems, please

call General’s customer service department at

412-771-6300.

SAVE THESE INSTRUCTIONS!

GENERAL SAFETY INSTRUCTIONS

D-25 Handy™

Electric shock resulting in

death can occur if you plug

your drill into an improperly

wired outlet. If the ground wire

is electrified, you can be elec-

trocuted by just touching the

machine, even when the power

switch is off. A ground fault cir-

cuit interrupter will not protect you

in this situation. Use a UL ap-

proved tester to determine if the

outlet is safe.

Do not operate power tools in

explosive atmospheres, such

as in the presence of flamma-

ble liquids, gases, or dust.

Power tools create sparks which

may ignite the dust or fumes.

Only wear leather gloves.

Never use any other type of

glove, such as cloth, rubber, or

coated gloves. Never grasp a

rotating cable with a rag.

These items could become

wrapped around the cable and

cause serious injury.

Always wear safety glasses

and rubber soled, non-slip

shoes. Use of this safety equip-

ment may prevent serious injury.

Do not overstress cables.

Overstressing cables may cause

twisting, kinking, or breaking of

the cable and may result in seri-

ous injury.

DANGER indicates a hazard with a high level of risk

which, if not avoided, will result in death or serious injury.

WARINING indicates a hazard with a medium level of risk

which, if not avoided, could result in death or serious injury.

CAUTION indicates a hazard with a low level of risk which,

if not avoided, will result in minor or moderate injury.

This is the safety alert symbol. It is

used to alert you to potential personal

injury hazards. Obey all safety mes-

sages that follow this symbol to avoid

possible injury or death.

D-25 Handy™

Specific Safety Information

1. Only wear leather gloves.Never use any other type

of glove, such as cloth, rubber, or coated gloves.

Never grasp a rotating cable with a rag. These items

could become wrapped around the cable and cause

serious injury.

2. Be sure that your drill is plugged into a properly

grounded receptacle. If in doubt, check receptacle

before plugging in tool. Check the power cord to see

that there are no cuts or frays, and that the grounding

prong on the plug is still in place.

3. If the power cord supplied with your drill is not

long enough, be sure to use a 16 gauge heavy

duty extension cord no more than 50 feet long

and in good condition. Using lighter cords can re-

sult in severe power loss and motor overheating.

4. Place the tool as close as possible, but not more

than six inches from the opening. Greater dis-

tances can result in cable twisting or kinking.

5. Tool is designed for ONE-PERSON operation. Op-

erator must control trigger switch and cable.

6. Never take hold of a rotating cable. Pull the cable

out, or push it back into the container by hand only

when the drill is stopped. When the drill is turning,

always have one hand controlling the trigger switch

and the other hand around the grip sleeve. Opera-

tor’s hand may be caught in the moving parts result-

ing in serious injury.

7. Be careful when cleaning drains where cleaning

chemicals have been used. Avoid direct contact

with corrosive drain cleaners. Drain cleaning chemi-

cals can cause serious burns, as well as damage the

cable. Neutralize or remove corrosive drain cleaners

in the drain before starting the job.

8. Do not operate tool with electric drill if operator

or tool is standing in water. Will increase risk of

electrical shock.

9. Wear safety glasses and rubber soled, non-slip

shoes. Use of this safety equipment may prevent

serious injury.

10. Before starting each job, check that the cable in

the drum is not broken or kinked, by pulling the

cable out and checking for wear or breakage.Al-

ways replace worn out (kinked or broken) cables with

genuine GENERAL replacement cables.

11. Only use this tool in the application for which it

was designed. Follow the instructions on the proper

use of the tool. Other uses or modifying the drain

cleaner for other applications may increase risk of

injury.

CABLE APPLICATION CHART

Cable Size Pipe Size Typical Applications

1/4” 1" to 2" Small lines, tubs, and shower drains.

5/16" 1" to 2" Sinks, basins, and small drains.

3/8" 1" to 2" Stacks, toilets, small drains (No Roots).

Hint: It's often helpful to have a small stream of

water running in the line to wash the debris away

while the tool is in operation and after.

Operating Instructions

Manual Operation

1. Place tool as close as possible, but not more than six

inches from the drain opening. If you can’t place the

tool this close to the drain opening, run the cable

through a hose or pipe to prevent cable whipping.

2. Loosen the chuck. Insert the cable into the drain

opening as far as it will go. Tighten the chuck by

turning it in a counter-clockwise direction.

3. Turn the tool clockwise, using a slight forward pres-

sure, until the exposed length of cable enters the

drain.

4. Loosen the chuck and pull the container back about

six inches.

5. Tighten chuck and repeat procedure until drain is

open.

6. When line is clear, retract cable while continuing to

rotate the container in the clockwise direction.

Cables are available with either a regular basin plug head

(as pictured above) or an optional down head (as shown

on the cover) to help the cable get around tight bends.

Andere General Pipe Cleaners Pfeifenreiniger Handbücher

General Pipe Cleaners

General Pipe Cleaners JM-3055 Bedienungsanleitung

General Pipe Cleaners

General Pipe Cleaners I-95 Bedienungsanleitung

General Pipe Cleaners

General Pipe Cleaners Mini-Rooter XP Bedienungsanleitung

General Pipe Cleaners

General Pipe Cleaners Sewerooter T-3 Bedienungsanleitung

General Pipe Cleaners

General Pipe Cleaners Speedrooter 92R Bedienungsanleitung

General Pipe Cleaners

General Pipe Cleaners Mini-Rooter Bedienungsanleitung

General Pipe Cleaners

General Pipe Cleaners Speedrooter 92 Bedienungsanleitung

General Pipe Cleaners

General Pipe Cleaners The Metro Bedienungsanleitung

General Pipe Cleaners

General Pipe Cleaners JM-1450 Bedienungsanleitung

General Pipe Cleaners

General Pipe Cleaners JM-2900 Bedienungsanleitung

General Pipe Cleaners

General Pipe Cleaners JM-3000 Bedienungsanleitung

General Pipe Cleaners

General Pipe Cleaners Speedrooter 92 Bedienungsanleitung

General Pipe Cleaners

General Pipe Cleaners Mini-Rooter XP Bedienungsanleitung

General Pipe Cleaners

General Pipe Cleaners Power-Vee Bedienungsanleitung

General Pipe Cleaners

General Pipe Cleaners Speedrooter XL Bedienungsanleitung

General Pipe Cleaners

General Pipe Cleaners Auto Handy PD-25 Bedienungsanleitung

General Pipe Cleaners

General Pipe Cleaners Sewermatic 100 Bedienungsanleitung

General Pipe Cleaners

General Pipe Cleaners Metro-Rooter Bedienungsanleitung

General Pipe Cleaners

General Pipe Cleaners Gen-Eye SD Bedienungsanleitung

General Pipe Cleaners

General Pipe Cleaners speedrooter 91 Bedienungsanleitung

General Pipe Cleaners

General Pipe Cleaners P-T3 Bedienungsanleitung

General Pipe Cleaners

General Pipe Cleaners Speedrooter 92 S92-450 Bedienungsanleitung

General Pipe Cleaners

General Pipe Cleaners Flexi-Rooter 100 Bedienungsanleitung

General Pipe Cleaners

General Pipe Cleaners Cold-Shot Bedienungsanleitung

Beliebte Pfeifenreiniger Handbücher anderer Marken

Virax

Virax VAL 80 Bedienungsanleitung

Ribimex

Ribimex Ribitech PRFDP Betriebsanleitung

PICOTE

PICOTE MINI SMART HEAT MILLER Gebrauchs- und Pflegehandbuch

Parkside

Parkside 270382 Bedienungsanleitung

PICOTE

PICOTE Smart Spider DN150/6" Bedienungsanleitung

Dali

Dali GQ-75 Bedienungsanleitung

Kompernass

Kompernass 64586 Bedienungsanleitung

Inder

Inder Power P-30 Bedienerhandbuch

Gap Power

Gap Power Speedrooter 92R Bedienungsanleitung

Parkside

Parkside 102800 Betriebsanleitung

Wöhler

Wöhler DH 420 Bedienungsanleitung

Elliott

Elliott Roto-Jet II Series Handbuch

Westfalia

Westfalia 82 45 38 Bedienungsanleitung

RIDGID

RIDGID KWIK-SPIN Bedienungsanleitung

Milwaukee

Milwaukee M18 FFSDC Bedienungsanleitung

Roller

Roller Ortem 22 Bedienungsanleitung

Stihl

Stihl 4910-500-8000 Bedienungsanleitung

REMS

REMS Cobra 32 Bedienungsanleitung