Generalscan GS-M100BT Bedienungsanleitung

M Series Quick Start Guide

Thanks for you use Generalscan all series barocde scanner product!

Please be sure to read this quick start guide before you use our product in first time.

Optimal Scanning Distance

GS-M100BT and GS-R1000BT series bluetooth barcode scanner's best scanning

distance is between 5 cm to 20 cm which depend on the density of barcode .

GS-M300BT series bluetooth barcode scanner are divided into high density and

low density model. Optimal scanning distance of Low density model is 10-24 cm.High

density model 's scanning distance is 3-7 cm .It can read higher density barcode like

3mil.

GS-M500BT series 2D bluetooth barcode scanner 's best scanning distance is 7cm

-10 cm. Please scan barcode in this range to obtain the best performance.

Scanning Techniques

Please aim at the middle of the barcode through the red light when scan the

barcode.

Please scan properly in accordance with the following diagram,adjust the scanner

angle and distance slowly ,at the same time ,press the trigger button ,make the centre

red light cover the left to right of the barcode .

Do not use the second image to scan barcode .

Model GS-M100BT GS-M300BT GS-M500BT GS-R1000BT

Interface Micro-USB Micro-USB Micro-USB Micro-USB

Charging Voltage DC-5V 0.15A DC-5V 0.15A DC-5V 0.5A DC-5V 0.15A

Battery Volume 500maH 300maH 600maH 350maH

Charging Time 5 hour 3 hour 5 hour 3 hour

Working Time(10s

interval trigger with

good decode)

12 hour 8 hour 14 hour 9 hour

Charging Function

Working with Mobile Phone Adapter

M series bluetooth barcode can fix on the mobile phone adapter. You can stick the adapter

on the back of mobile phone protective case with magic double side sticker.So you can take the

scanner with smartphone with one hand .

Please fix mobile phone adapter in th clip on the back of scanner ,The steps is shown in the

following figure:

Installation Step

Figure-1 ,Put the

front of scanner into

the clip of adapter

Figure-2，Press the

bottom of scanner

,make the clip of

adapter claw at the

scanner.

Dismantle Step

Figure-3 ，Put the

clip of adapter to

outside

Figure-4,Put scanner

up from the adapter

and take out the

scanner.

Figure-1

Figure-3

图二

Figure-2

Figure-4

M Series Quick Start Guide

Item Name Description

1 Scanning Window Reading barcode ,Red light or Laser will beam out from this window

2 Buzzer Hole The buzzer will sound when good decoded：

（1）Connect USB cable，buzzer will beep “b....b.b.”；

（2）Good decoed：Flashing green light and buzzer one time.

3 Trigger Button Press the trigger button to scan the barcode one time,Double click to

hide and display soft keyboard in iOS device like iphone or iPad.

4 Status LED

LED has three color (Red,Green,Blue) which indicate with different

scenario.Please reference the following table for detail description

5 Strap Hole Fix strap into this hole

6 MicroUSB

Charge with bluetooth barcode scanner with Micro-USB or connect

PC with USB port.

7 Power Switch Swith to left or right to power on the scanner of turn off the scanner.

Please turn off the power to save power.

8 Buckle forAdapter Use for buckle scanner with adapter

9 Magic Strap Hole Take the yellow magic strap through the hole to wear it on the finger

10 Battery cover Take off the battery cover to change the battery

Function Description

LED Indicator Description

Item Status Description

1 Green LED light flashing (with buzzer sound) Decode success

2 Green LED light flashes continuously Low battery alarm

3 Red LED light constant light Charging

4 Red LED light turn off Charging is complete

5 Red LED light flashes continuously Built-in battery abnormal

6 Blue LED continuously flashing Enter the Bluetooth pairing mode

7 Blue LED turn off Bluetooth Pairing successful

Product Outlook

①

②

③

④

⑤

⑥⑦

⑧

①②

③

④

①

⑦

⑥⑨

⑩

⑾

R Series Quick Start Guide

Bluetooth Pairing and Data Transfer

When you first time use Generalscan GS-M series bluetooth barcode,the default

data transfer interface is bluetooth ,You can pairing bluetooth barcode scanner with

Android ,iOS,WP8 smartphone or Windows tablet. For detail instruction ,please

reference the following document：

http://www.generalscan.com/pdf/BluetoothPairUserGuide-english.pdf

When you connect with Android and iOS smartphone,please confirm the data

interface is Bluetooth ,If you don't confirm ,please scan the following barcode to

switch Bluetooth mode.

Set Bluetooth Output

The bluetooth have two transfer protocol ,One is HID keyboard ,You can use this

protocol as a external keyboard.Android and iOS support HID ,You don't need install

any software to use HID.You can scan barcode into the cursor position.Please scan

the following barcode to switch HID mode：

HID Mode

Another mode is SPP mode. This mode is wireless serial port mode .Android

system support SPP mode ,but iOS don't support this mode free, When you connect

Android not successful in HID mode ,please switch to SPP mode.

SPP Mode

When you connect with Android and iOS device ,please scan the Enter Pairing

Mode barcode first .You will see the blue LED will blink after scan Enter Pairing Mode

barcode, then scan device in Android and iOS setting interface,The name of GS-M

serial bluetooth barcode will display as "GS-BarcodeScanner"

Enter Pairing Mode

After you pairing successfuly ,the blue LED will stop blink.

The detail pairing procedure for Android ,iOS ,WP8 ,please reference the

following video：

http://www.generalscan.com/video.php

Bluetooth Pairing Guide

SL Series Product Outlook

①②

③

④

⑤

⑥

⑦

⑧

⑨

Item Name Description

1 Scanning Windows Reading barcode ,Red light or Laser will beam out from this window

2 Screw Hole Screw hole to fix the top cover

3 Top cover To fix the smartphone in the sled

4 Ear Phone Hole Plug the ear phone

5 Trigger Button Press the trigger button to scan the barcode one time

6 Power Button Smartphone power button.

7 Battery Door Open battery door to take out battery

8 Micro USB Plug Slide smart phone into sled and plug into smartphone

9 Volume Key Adjust smartphone volume

10 Strap Hole To fix the strap

11 Power Swtich Power on or power off

12 Micro-USB Plug Charging for sled

Function Description

LED Indicator Description

LED Status Status

Blue LED turn on Indicate Android smartphone detect the Sled successfully.

Red LED turn on Battery Charging

Smartphone Installation

1.Reference figure-3,take off the top cover.

2.Slide the smartphone into sled

3.Plug the phone into micro usb plug

slowly and carefully

4.close the top cover and secure the top

cover with screw ,reference figure -2

5.Reference figure-6，power up the

smartphone

6.switch on the power of sled ,Android

phone will detect the USB accessory device

7.Install Generalscan Input or SDK to scan

barcode.

⑨⑩

⑾⑿

SL Series Quick Start Guide

WT Series Product Outllook

Item Name Description

1 Power Switch Switch to left or right for power on /off

2 External Charging Port Only for GS-WT1000BT for charging GS-R1000BT

3 LED Indicator(Blue or Red

color)

USB Accessory LED,When USB Accessory detected by

Android,The blue led will turn on.When in

charging,red LED will turn on.

4 Micro USB Charging for internal battery

5 Buckle Button for Armmount Press the button to dismantle the arm mount

6 Strap Hole Fix the magic sticker

7 Spring cable for scanner Connect ring scanner to arm mount

8 Smart phone Platform Use double side magice sticker to fix smartphone

9 Battery Door Open the door to change the battery

10 Buckle for battery door To fasten the battery door

11 Smartphone Micro-USB plug for communication with smartphone

Function Description

①②

③

④

⑤

⑥

⑦

⑧

⑨

③

⑨

⑩

⑾

WT Series Installation

1.Put the smartphone with protective case

and fix with double side magic sticker

2.Reference figure-11, plug Micro-USB into

Android smartphone

3.Put the battery into compartment and close

the battery door.

4.Power on the pow switch (Figure-1),make

sure the blue LED turn on.

5.Power on the ring scanner power switch.

6.Install Generalscan Input or SDK to use.

WT Series Quick Start Guide

You should install driver in Android system before use GS-SL series and GS-WT series

barcode device.

Note: Only Android 4.0 or above system support this device.

You have two way to install the driver, one is Generalscan Input IME. Another is GS-

SDK development kit .You can embedded SDK into your application to scan barcode

directly.

Generalscan Input Installation and Usage

Please download the Generalscan Input APK and help document from the following

address:

http://www.generalscan.com/pdf/Generalscan-Input.apk

http://www.generalscan.com/pdf/GS-BlueInput-UserManual.pdf

This input IME APK compatiable with Generalscan bluetooth barcode scanner.When

you use for GS-SL series and GS-WT1000 series product,you don't need any setting for

it .

After you install Generalscan-Input.apk into Android smartphone,Please check

Generalscan input and set Generalscan Input as default input method.

When GS-SL and GS-WT power on normally,Android smartphone will detect the

USB accessory device,at the same time ,the smartphone battery inidcator will turn into

charging mode. The blue LED will turn on .The status bar in Android smartphone will

display as“Connected as a media device”and“Connected to a USB accessory“

eneralscan SDK Installation and Usage

When you use GS-SDK devlopment kit to use GS-SL，GS-WT series product ,you

don't need install Generalscan Input. Please download the GS-SDK developemtn kit

from the following address:

http://www.generalscan.com/pdf/FinalSDK-Public.zip

Unzip FinalSDK-Public.zip file, you will find the following folder and file：

GeneralscanUSBBroadcast.apk

USB Accessory Broadcast server App

usb-service-server This directory is source code for USB Accessory Broadcast server

App.You can modify this source code yourself and start service and run it in background

.Don't kill this service or end task by task manager.

GeneralscanUSBBroadcastTest.apk

This APK is Broadcast receiver demo APK.

usb-service-test

This directory is source code for broadcast receiver APK.

Please use Eclipse to import all souce code

Note：

Please use service to invoke the Generalscan USB Accessory JAR libaray ，it will

decrease the CPU utilization ,improve the battery power comsuption.

GS-SL Series and GS-WT Series SDK and App Introduction

Android USB Accessory SDK Guide

Factory Reset

USB Accessory Sleep Disable

Sled Battery Information Upload Enable

SLed Battery Information Upload Disable

Enter Standard Charging Mode

Enter Quick Charing Mode

USB Accessory Sleep in 60 minutes

All Series Programming Bar Code

Andere Handbücher für GS-M100BT

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Generalscan Barcode-Lesegerät Handbücher

Generalscan

Generalscan GS-M100BT Bedienungsanleitung

Generalscan

Generalscan R1000BT Series Bedienungsanleitung

Generalscan

Generalscan Scanbuddy GS-X3 Bedienungsanleitung

Generalscan

Generalscan GS WT5000X Bedienungsanleitung

Generalscan

Generalscan FS01&MS3391-L Bedienungsanleitung

Generalscan

Generalscan X Series Bedienungsanleitung

Generalscan

Generalscan MiniRing GS R5000BT-51C Bedienungsanleitung

Generalscan

Generalscan GS-X Series Bedienungsanleitung

Beliebte Barcode-Lesegerät Handbücher anderer Marken

POSMicro

POSMicro Datalogic PowerScan D7100 Bedienungsanleitung

Marson

Marson MT780 Kurzanleitung zur Einrichtung

NCR

NCR RealPOS Bedienungsanleitung

Motorola

Motorola SE3300 Kurzanleitung zur Einrichtung

Element

Element P130BT Bedienungsanleitung

Motorola

Motorola Symbol LS3008 Installations- und Betriebshandbuch

Meec tools

Meec tools OBD-II / VAG Bedienungsanleitung

SICK

SICK CLP 100 Bedienungsanleitung

Royal Tag SA

Royal Tag SA I-Read Bedienungsanleitung

Welch Allyn

Welch Allyn IMAGETEAM 3800 Bedienungsanleitung

Meteor

Meteor 8310 Bedienungsanleitung

Denso

Denso BHT-500B Bedienungsanleitung

Datalogic

Datalogic Heron HD3130 Bedienungsanleitung

Motorola

Motorola MP6000 Montageanleitung

Newland

Newland NLS-HR15-BT Bedienungsanleitung

ARTDEV

ARTDEV AS-1310 Bedienungsanleitung

Aopos

Aopos AS290 Bedienungsanleitung

ENS

ENS 367-5455 Bedienungsanleitung