Genesis Pulse EX600 Bedienungsanleitung
Pulse
EX600
Installation Guide
Wi-Fi EasyMeshTM supported
Box contents
• Genexis Pulse EX600
• Power adapter
• Network cable
• Labels (self-adhesive)
• Plugs & screws
Genexis EasyWiFi app
Installation and management of the
Pulse EX600 can be done with help
of the mobile application Genexis
EasyWiFi for the applicable installation
modes as described in this installation
manual. Please follow the steps on the
left page.
Warning: Do not cover the device
with anything because this will
interfere with the ventilation of the
Pulse EX600.
Operation Temperature 0°C ~ 40°C
Placement
Pulse EX600 supports two placement
options; desktop and wall-mounted.
It is recommended to place the device
'away' from obstacles and objects.
Desktop
1. Place the device horizontally on a
at surface.
Wall-mount
1. Download and print the drilling
guide from hps://genexis.eu/
product/pulse/downloads
2. Use the drilling guide to drill the
holes, insert plugs and put
screws into place.
3. Use the wall mount points on the
back of the Pulse EX600 to mount
the device to the screws.
Installation guide
You're just a few steps away to install your
device via the Genexis EasyWiFi app
Scan QR-code
Download app and
follow the steps
1
2
Installation with use of app
Pulse EX600
Router
Extender placement
For optimal performance of the
Pulse EX600 as extender; place the
Pulse EX600 halfway in between
your router and the problem area (as
shown below). Make sure placement
is within WiFi range of your router. If
the extender is placed too far away, it
cannot connect to the router.
Problem area, improved
by Pulse EX600
Area that is good for
placing Pulse EX600
Area covered by your
router
Seing up your Pulse device(s)
This installation guide is for installing
the Pulse EX600 as a router, as
explained on the right. In addition, an
extra Pulse EX600 can be installed as
a wireless or wired extender behind
the Pulse EX600 router.
Router
If you do not have a router installed,
start installing your Pulse EX600 here:
1. Connect a network cable between
your broadband outlet and the Pulse
EX600 WAN port (red port).
2. Connect the supplied power adapter
to the Pulse EX600 and plug the
adapter into a power socket.
3. Flip the ON/OFF switch at the back
of the device to turn it on.
4. Wait until the Status LED stops
blinking and turns solid green.
Your Pulse EX600 is now setup as a
router. Your network is now ready to
be extended with a wireless or
wired extender, as explained on the
next pages.
Switching the WiFi ON/OFF
The WiFi function of the Pulse EX600
can be switched ON or OFF by
means of the Mode buon.
• Switch OFF: On the Pulse EX600,
press and hold the Mode buon until
the Status LED turns solid yellow.
• Switch ON: On the Pulse EX600,
press and hold the Mode buon until
the Status LED starts blinking green
or turns solid green.
Connecting to the wireless network
Automated pairing
You can connect your personal device
to the Pulse EX600 by scanning the
QR-code on the label of the Pulse
EX600 or use the Mode buon (WPS
function) of the Pulse EX600. Please
check on your personal device how this
can be initiated. Before pairing, make
sure the Status LED is solid green. If
not, switch the WiFi ON as described in
this installation guide.
Manual pairing
You can also connect your personal
device to the Pulse EX600 via manual
pairing using the WiFi network name
and WiFi key printed on the label of
the Pulse EX600.
1. Perform a search of available wireless
networks on your personal device.
2. Select the WiFi network name
printed on the label.
3. Enter the WiFi key printed on
the label.
Follow the instructions of the router in
case the Pulse EX600 is in
extender mode.
Wireless extender
1. Place the additional Pulse EX600 as
described on the previous page.
2. Connect the supplied power adapter
to the Pulse EX600 and plug the
adapter into a power socket.
3. Flip the ON/OFF switch at the back
of the device to turn it on.
4. Wait until the Status LED
surrounding the Mode buon starts
blinking green.
5. On the Pulse EX600, press and
release the Mode buon once. The
status LED will start blinking blue.
6. Press the same Mode buon on the
Pulse EX600 router within
two minutes.
7. Automated pairing is now started.
8. The Status LED turns solid blue
indicating that pairing of the Pulse
EX600 extender with the router
is successful (the Pulse EX600 will
automatically reboot after the
automated pairing; this may take up
to several minutes).
9. Wait until the Status LED stops
blinking and turns solid green.
Your Pulse EX600 is now setup as a
wireless extender.
Wired extender
1. Connect a network cable between
the LAN port (yellow connector)
of the Pulse EX600 router and the
WAN port (red connector) of the
Pulse EX600 extender.
2. Connect the supplied power adapter
to the Pulse EX600 and plug the
adapter into a power socket.
3. Flip the ON/OFF switch at
the back of the device to turn it on.
4. Wait until the Status LED
stops blinking and turns solid green
(the Pulse EX600 extender will
automatically reboot during the
setup; this may take up to
several minutes).
Your Pulse EX600 is now setup as a
wired extender.
LED & button overview
Status
Green – system is operational ready
Green (blinking) – no broadband connectivity
Yellow – system startup or WiFi OFF
Yellow (blinking) – system is not ready yet
Blue – automated pairing (WPS) successful
Blue (blinking) – automated pairing (WPS) in progress
Red – system / booting failure
O – power o
Mode buon
Pairing (WPS) – press and release once
WiFi ON – press and hold until Status LED turns
green (blinking or solid)
WiFi OFF – press and hold until Status LED turns
solid yellow
Using the web interface
When connected to your network,
you can access the Pulse EX600
web interface to change your device
seings.
1. Use a browser on your personal device
and navigate to 'GUI' as printed on
the label of the Pulse EX600.
2. Login by inserting the 'Username'
and 'Password'.
3. If required, change your device
congurations.
USB 2.0
port
Port overview
Power port
ON/OFF
switch
Reset
buon
WAN port
LAN ports
ON/OFF switch
Switch ON – ip the switch to ON
Switch OFF – ip the switch to OFF
Reset buon (recessed)
Reboot – press and release once
Factory reset – press and hold until the
Status LED starts fast blinking green
Return the Pulse EX600 to factory
default seings
With the reset buon you can reset
the Pulse EX600 to its factory default
seings. You can press this buon with
a small pin or paperclip.
1. Press and hold the reset button
until the Status LED starts fast
blinking green.
2. Wait until the Status LED turns solid
green again.
Your Pulse EX600 is now setup as
a router again with the seings as
printed on the label.
Support
Is the Status LED solid red?
Contact your service provider.
Is the Status LED solid yellow?
The WiFi of the Pulse EX600 is turned
OFF. Please turn the WiFi ON as
described in this installation guide.
Is the Status LED not solid blue after
automated pairing (WPS)?
Automated pairing (WPS) between the
Pulse EX600 and Genexis router or
personal device failed. Please follow
the instructions again to setup the
Pulse EX600 as a wireless extender or
connecting your personal device to the
wireless network. It might be helpful to
move the Pulse EX600 closer to your
Genexis router.
Is the Status LED blinking green for
5 minutes?
• Router: Pulse EX600 does not have
a connection with the broadband
network. Please verify your wired
connection with the broadband
outlet or contact your
service provider.
• Wireless/wired extender:
Connection between the Genexis
router and the Pulse EX600 is not
stable. Please check the cable
connection with the Genexis router
or move the Pulse EX600 closer to
the Genexis router.
Is the Status LED blinking yellow?
The Pulse EX600 is being upgraded
with new software. Please wait until the
Status LED turns solid green again.
Company Name
Genexis Netherlands B.V.
Company Address
Lodewijkstraat 1a
5652 AC Eindhoven
The Netherlands
Name and title of authorized person
Maarten Egmond, CTO
Signature of authorized person
Place of issue Date of issue
Eindhoven 2021-10-06
The Netherlands
Hereby, Genexis Netherlands B.V. declares that the product Pulse EX600 is in
compliance with Directives 2014/53/EU, 2009/125/EC, 2011/65/EU and Delegated
directive 2015/863.
The full text of the EU declaration of conformity is available at the following internet
address: hps://genexis.eu/product/pulse/red/pulse-ex600
EU Declaration of Conformity
Frequency bands and maximum radio frequency power transmied
The Pulse EX600 operates in the frequency bands of 2,4 Ghz and 5Ghz.
The maximum radio frequency power transmied in these bands is:
• 20 dBm(100 mW) (EIRP)for the 2400 MHz – 2483.5 MHz band
• 23 dBm (200 mW) (EIRP)for the 5150 MHz – 5350 MHz band *
• 30 dBm (1000 mW) (EIRP) for the 5470 MHz – 5725 MHz band
* In EU, 5150 – 5350 MHz is restricted to indoor.
Revision 2.0 - October 2023 - Copyright ©2023 Genexis Netherlands B.V. All rights reserved.
Multiple languages of this document and additional product information are availableon
hps://genexis.eu/product/pulse/downloads
Genexis assumes no responsibility for any inaccuracies in this document. Genexis reserves the right to change,
modify, transfer, or otherwise revise this publication without notice.
Inhaltsverzeichnis
Andere Genesis Netzwerk-Hardware Handbücher
Beliebte Netzwerk-Hardware Handbücher anderer Marken
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung
Yudor
Yudor YDS-16 Bedienungsanleitung
D-Link
D-Link ShareCenter DNS-320L Bedienungsanleitung
Samsung
Samsung ES1642dc Gebrauchsanweisung
Honeywell Home
Honeywell Home LTEM-PV Montageanleitung
