Genexis FiberTwist Bedienungsanleitung

FiberTwist

Network Termination

Quick Installation Guide ....................................................................1

Schnellinstallationsanleitung............................................................13

FiberTwist

Network Termination

Quick Installation Guide

In the box

Model: Fibertwist-X0000

PN: 996160001

SN: Z.000001001

CLASS 1

LASER PRODUCT

+12v 0.5A

2016-05 VER.1.0

Made in India

GPON SN:GNXS01000001

FiberTwist

Active device

(exact appearance differs depending on the model)

Label

Please retain for future reference.

Power Adaptor

Use only the supplied power adaptor.

Model

G2110

G2120

P2110

P2410, P3410,

G2410

P2420, P3420,

G2420

Models Supported

Overview (side)

Unlock button: press and hold while twisting to the left to

remove the FiberTwist or blind cover from the FTU (ber

termination unit).

Reset button: *

• press and release to reset (retain custom settings)

• press and hold for more than 5 seconds to perform a factory

reset (deletes all custom conguration)

Dim button: dims the lights on the device as described below.

* On some models, the reset button is on the end of the device next to the power

connector. Not present on the P2110.

Dim button behaviour (all models)

Each press of the dim button cycles through the following sequence of

brightness levels:

fully lit offhalf lit

(not on the P2110)

Overview (end)

CATV * LAN ports power connector

Point to Point Series

power switch

power connector

reset button

LAN port

GPON series

* not present on all models

Installation

1. Preparation

Ensure there is a power socket within 80cm of where the device is being

installed.

Open the FiberTwist box (but don’t yet remove the FiberTwist from the box)

and place the box near where the FiberTwist is to be installed.

Important: It is crucial the following steps all be completed

in one go. Failure to do so could result in damage to the

bre optic connectors, causing a severe degradation of

signal quality.

2. Remove the blind cover (if present)

Press and hold the unlock button.

Rotate the blind cover counter-

clockwise (in the direction of

the arrow).

When it won’t rotate any

further, the blind cover can be

removed.

Please store the blind cover in a safe place.

3. Remove dust cap

Take the FiberTwist out of its box.

The dust cap is the bright red tab located on the rear of the FiberTwist

(pictured below).

Remove the dust cap by holding the end of the red tab and pulling it gently

in the direction of the arrow.

Please store the dust cap in a safe place.

Andere Handbücher für FiberTwist

Inhaltsverzeichnis

Sprachen:

Andere Genexis Netzwerkzubehör Handbücher

Genexis

Genexis FiberTwist Bedienungsanleitung

Beliebte Netzwerkzubehör Handbücher anderer Marken

Valcom

Valcom VIP-804 Bedienungsanleitung

SKUTCH

SKUTCH BA-1000 Produkthandbuch

QUNDIS

QUNDIS RNN5 Bedienungsanleitung

Asus

Asus AAEON FWS-2365 Bedienungsanleitung

Sophos

Sophos XG 85w Bedienungsanleitung

AMCI

AMCI RBE2-8 Bedienungsanleitung

Patton electronics

Patton electronics 2888 Bedienungsanleitung

Cradlepoint

Cradlepoint COR IBR1100/IBR1150 Bedienungsanleitung

Paradyne

Paradyne Hotwire 8620 Bedienungsanleitung

Infra Cool

Infra Cool F-1.3 Bedienungsanleitung

Edgewater Networks

Edgewater Networks 4300T Bedienungsanleitung

Edimax

Edimax SB-2200g Bedienungsanleitung

Extreme Networks

Extreme Networks Mogul-100 Bedienungsanleitung

Aaeon

Aaeon FWS-8500 Bedienungsanleitung

Panduit

Panduit Z11C Series Bedienungsanleitung

F5 BIG-IP 10000 Series Montageanleitung

ZyXEL Communications

ZyXEL Communications NMA1115 Bedienungsanleitung

Auerswald

Auerswald COMtrexx Business Bedienungsanleitung