Genie S-80HF Bedienungsanleitung

Maintenance Manual

- Booms

S®Booms

This manual includes detailed

procedures for each

maintenance inspection.

Z®Booms

For Repair procedures, Fault

Codes, Electrical and Hydraulic

Schematics, refer to the

appropriate Service and Repair

Manual for your machine.

Refer to the inside cover for a list of models

included in this manual.

Part No. 1268489GT

Rev G

October 2018

Maintenance Manual October 2018

Introduction

ii S®Booms • Z®Booms Part No. 1268489GT

Intr od ucti on Intr od ucti on

Important

Read, understand and obey the safety rules and

operating instructions in the appropriate Operator's

Manual on your machine before attempting any

maintenance procedure.

This manual provides detailed scheduled

maintenance information for the machine owner

and user.

Basic mechanical, hydraulic and electrical skills are

required to perform most procedures. However,

several procedures require specialized skills, tools,

lifting equipment and a suitable workshop. In these

instances, we strongly recommend that

maintenance be performed at an authorized Genie

dealer service center.

Compliance

Machine Classification

Group B/Type 3 as defined by ISO 16368

Machine Design Life

Unrestricted with proper operation, inspection and

scheduled maintenance.

Technical Publications

Genie has endeavored to deliver the highest

degree of accuracy possible. However, continuous

improvement of our products is a Genie policy.

Therefore, product specifications are subject to

change without notice.

Readers are encouraged to notify Genie of errors

and send in suggestions for improvement. All

communications will be carefully considered for

future printings of this and all other manuals.

Internet: www.genielift.com

E-mail: awp.techpub@terex.com

1268489 Rev G, October 2018

First Edition, Seventh Printing

Genie, "S" and "Z" are registered trademarks of Terex South

Dakota, Inc. in the U.S.A. and many other countries.

"TraX" and "XC" are trademarks of Terex South Dakota, Inc.

October 2018 Maintenance Manual

Introduction

Part No. 1268489GT S®Booms • Z®Booms iii

Models included in this manual

Use the following chart to identify the specific serial

number for models included in this manual.

Models

Serial number

-40, S-45 from S4015-20505 to S4016H-23499

from S4515-20505 to S4516H-23499 from

S40H-23500 from S45H-23500

-60, S-65,

-60XC,

-65XC

from S6013-29296 to S6016-31260

from S6016N-31261 to S6016N-35000

from S6016H-35001 to S6016H-36399

from S6014D-101 to S6016D-639

from S6016M-101 to S6016M-399

from S60X13-26296 to S60X16H-36399

from S60XC13-26296 to S60XC16H-36399

from S60HC13-26296 to S60HC15A-29544

from S60TX13-26296 to S60TX16H-36399

from S60TX14D-101 to S60TX16D-639

from S65TX13-26296 to S65TX16H-36399

from S65TX14D-101 to S65TX16D-639

from S60H/S60X/S60TX/S65TXH-36400

from S60XCH-36400 to S60XCH-45000

from S60XCH/S65XCH-45001

from S60/S60TX/S60XD-640

from S60M-400

from S65XCM-101

from S65TXM-101

-80, S-85,

-80XC,

-85XC.

-80HF,

-85HF

from S80/85/80X15

-12264 to16H-13999

from

S80/85/80X15D-101 to 16D-339

from S80/85/80XH

-14000

from S80/85/80XD

-340

from S80/85XCH

-101

-100, S-105

from S10015D

-1001 to S10016D-1549

from S10515D

-983 to S10516D-1549

-120, S-125 from S12015D-1012 to S12016D-1549

from S12515D-984 to S12516D-1549

from S100/105/120/125D-1550

-100HD,

-120HD

from S100HD14D

-200 to S100HD16D-229

from S120HD14D

-201 to S120HD16D-229

from S100/S120HDD

-230

-105 XC

from SX105D

-101

-125 XC

from SX125D

-101

-135 XC

from SX135H

-101

-150

from SX15015

-100 to Sx15016H-499

from SX150H

-500

-180

from SX18014

-101 to SX18016H-599

from SX180H

-600

-30/20N,

-30/20N RJ

from Z30N14

-15222 to Z30N16F-18899

from Z30N16D

-104 to Z30N16D-199

from Z30NF

-18900

from Z30ND

-200

-33/18 from Z331815M-101 to Z331816M-1299

from Z3318M-1300

-34/22 DC from Z3414-9686 to Z3416F-11999

Z34F-12000

-34/22 N

from Z34N14

-10984 to Z34N16F-13999

from Z34N15D

-102 to Z34N16D-279

from Z34NF

-14000

from Z34ND

-280

-34/22 IC

from Z3406

-4800 to Z3413-9460

from Z3413

-9461 to Z3415-10688

rom Z3416F-10689 to Z3416F-11999

from Z34F

-12000

-34/22 BE

from Z3414

-9686 to Z3416F-11999

from Z34F

-12000

-40/23N RJ

from Z40N13

-1902 to Z40N16N-4499

from Z40NN

-4500

-45/25 DC,

-45/25J DC

from Z452513A

-48153 to Z452516N-57199

from Z452513B

-3078 to Z452516M-6699

from Z452513D

-101 to Z452516D-939

from Z4525D

-940

from Z4525M

-6700

from Z4525N

-57200

-45/25 IC,

-45/25J IC,

-45XC

from Z452513A

-47001 to Z452516N-57199

from Z452514B

-3301 to Z452516M-6699

from Z452513D

-101 to Z452516D-939

from Z4525D

-940

from Z4525M

-6700

from Z4525N

-57200

from Z4525XCM

-101

-45/25(J) BE

from Z452513A

-48153 to Z452516N-57199

from Z4525N

-57200

-51/30J

from Z513014B

-1201 to Z5130M-2000

from Z5130M

-2000

-60/37 DC,

-60/37 FE

from Z6016N

-101 Z6016N-599

from Z60N

-600

-62/40

from Z6215A

-101 to Z6216N-2999

from Z6216D

-108 to Z6216D-149

from Z6216M

-101 to Z6216M-399

from Z62D

-150

from Z62H

-3000

from Z62M

-400

-80/60

from Z8013

-4592 to Z8016H-6399

from Z80H

-6400

-135/70

from Z13505

-101 to Z13513-2000

-135/70

from

ZX13514-2533 to ZX13516H-3199

(includes 2463, 2469, 2531)

from ZX135H

-3200

Maintenance Manual October 2018

Introduction

iv S®Booms • Z®Booms Part No. 1268489GT

Identifying the Correct Procedure

for your Model

Unless otherwise noted, each procedure will apply

to all models. Procedures that only apply to specific

models or options will include the information in the

procedure title.

Examples of procedures that apply to specific

models:

•Test the Engine Idle Select - Engine

Models

•Test the Turntable Level Sensor - Z-80/60

•ALC600 Models, include the following

models: S-60 XC from S60XCH-45001 and

S60XCM-101, S-65 XC, S-80 HF, S-85 HF,

S-80 XC and S-85 XC.

•ALC1000 Models, include the following

models: S-100, S-100HD, S-105, S-120,

S-120HD, S-125, SX-105 XC, SX-125 XC,

SX-135 XC, SX-150, SX-180, Z-80/60,

Z-135/70 and ZX-135/70.

Examples of procedures that apply to all models:

•Test the Drive Speed – Stowed Position

•Inspect the Tires, Wheels and Lug Nut

Torque

Find additional Manuals for your

Model

Go to http://www.genielift.com

Use the links to locate Service Manuals,

Maintenance Manuals, Service and Repair

Manuals, Parts Manuals and Operator's Manuals.

October 2018 Maintenance Manual

Introduction

Part No. 1268489GT S®Booms • Z®Booms v

Revision History

Revision Date Section Procedure / Description

A 9/2015

Initial Release

A1 10/2015 Quarterly Q-27 Test the Primary Angle Sensor

A2 11/2015 Specifications Hydraulic and Drive Hub Capacities

A3 11/2015 Introduction Updated Z-80/60 serial number for models included

A4 12/2015 Quarterly Q-17 Inspect the Calibration Decal

A5 1/2016 Specifications Performance Spec. Z62

B 3/2016 All Sections Add Z-60 DC/FE

Specifications Add Kubota D1105-E4B, GM .998L, GM 3.0L.

Update Deutz D2.9 L4 and Perkins 404F engine rpm's.

B1 4/2016 Quarterly Q-7 Check the Generator Belts, Pulleys and voltage -

Bi-Energy Models

Annual A-3 Inspect for Turntable Bearing Wear

B2 6/2016 Specifications Tires and Wheels, add Z60 DC/FE

B3 9/2016 Introduction Models Included

C 11/2016 All Sections Add SX-135 XC

C1 12/2016 Quarterly Q-26 Test the Secondary Boom Angle Sensor

D 2/2017 Quarterly Q-36 Inspect and Adjust Boom Cables

Annual A-3 Inspect Turntable Bearing Wear

A-11, A-12, A-13 Inspect Boom Cables

Programmed P12-2 Remove and Inspect Boom Cables

Reference Examples:

Section – Specifications Electronic Version

Click on any content or procedure in the Table of Contents to view

the update.

Section – Maintenance, (procedure)

Maintenance Manual October 2018

Introduction

vi S®Booms • Z®Booms Part No. 1268489GT

Revision History (continued)

Revision Date Section Procedure / Description

E 3/2017 All Sections Add SX-125 XC and Z-45 XC

E1 3/2017 Programmed Remove 10 year cable inspection

F 6/2017 All Sections Add S80/85 XC, SX-105 XC

Specifications Add Deutz D436 L3i CN3 Engine

F1 4/2018 Specifications Deutz TD2011 Engine Specifications

G 10/2018 All Sections Add S60XC, S-65XC, S-80HF, S-85HF Models

Add Perkins 404F-E22T, 404F-E22TA Engine

Reference Examples:

Section – Specifications Electronic Version

Click on any content or procedure in the Table of Contents to view

the update.

Section – Maintenance, (procedure)

October 2018 Maintenance Manual

Safety Rules

Part No. 1268489GT S®Booms • Z®Booms vii

Section 1 Safet y R ul es

Danger

Failure to obey the instructions and safety rules in

this manual and the appropriate Operator's Manual

on your machine will result in death or serious

injury.

Many of the hazards identified in the operator's

manual are also safety hazards when maintenance

and repair procedures are performed.

Do Not Perform Maintenance

Unless:

You are trained and qualified to perform

maintenance on this machine.

You read, understand and obey:

•manufacturer's instructions and safety rules

•employer's safety rules and worksite

regulations

•applicable governmental regulations

You have the appropriate tools, lifting

equipment and a suitable workshop.

Maintenance Manual October 2018

Safety Rules

viii S®Booms • Z®Booms Part No. 1268489GT

Personal Safety

Any person working on or around a machine must

be aware of all known safety hazards. Personal

safety and the continued safe operation of the

machine should be your top priority.

Read each procedure tho

roughly. This

manual and the decals on the machine,

use signal words to identify the following:

Safety alert symbol

—

used to alert

personnel to potential personal

injury hazards. Obey all safety

messages that follow this symbol

to avoid possible injury o

r death.

Indicates a imminently hazardous

situation which, if not avoided, will

result in death or serious injury.

Indicates a potentially hazardous

situation which, if not avoided,

could result in death or serious

injury.

Indicates a potentially

hazardous

situation which, if not avoided,

may cause minor or moderate

injury.

Indicates a potentially hazardous

situation which, if not avoided,

may result in property damage.

Be sure to wear protective eye wear and

other protective clothing if the

situation

warrants it.

Be aware of potential crushing hazards

such as moving parts, free swinging or

unsecured components when lifting or

placing loads. Always wear approved

steel

-toed shoes.

Workplace Safety

Any person working on or around a machine must

be aware of all known safety hazards. Personal

safety and the continued safe operation of the

machine should be your top priority.

Be sure to keep sparks, flames and

lighted tobacco away from flammable and

combustible materials like battery gases

d engine fuels. Always have an

approved fire extinguisher within easy

reach.

Be sure that all tools and working areas

are properly maintained and ready for

use. Keep work surfaces clean and free of

debris that could get into machine

components and cause

damage.

Be sure any forklift, overhead crane or

other lifting or supporting device is fully

capable of supporting and stabilizing the

weight to be lifted. Use only chains or

straps that are in good condition and of

ample capacity.

Be sure that

fasteners intended for one

time use (i.e., cotter pins and self

-locking

nuts) are not reused. These components

may fail if they are used a second time.

Be sure to properly dispose of old oil or

other fluids. Use an approved container.

Please be

environmentally safe.

Be sure that your workshop or work area

is properly ventilated and well lit.

October 2018

Table of Contents

Part No. 1268489GT S®Booms • Z®Booms ix

Introduction Introduction...........................................................................................................ii

Important Information ............................................................................................. ii

Models included in this manual ............................................................................. iii

Identifying the Correct Procedure for your Model ................................................. iv

Find additional Manuals for your Model ................................................................ iv

Revision History...................................................................................................... v

Section 1 Safety Rules ........................................................................................................vii

General Safety Rules ........................................................................................... vii

Section 2 Performance Specifications ................................................................................1

Function Speeds - S-100, S-105 and S-100HD .....................................................1

Function Speeds - S-120, S-125 and S-120HD .....................................................2

Function Speeds - All Other Models ......................................................................3

Drive Speeds ..........................................................................................................9

Torque Specifications........................................................................................12

Tires and Wheels..................................................................................................12

TraX Torque Specifications ..................................................................................13

Engine Specifications ........................................................................................14

Engine Operator and Maintenance Manuals........................................................14

Deutz Engine Models ...........................................................................................15

Perkins Engine Models.........................................................................................16

Ford Engine Models .............................................................................................18

Kubota Engine Models .........................................................................................18

GM Engine Models ...............................................................................................19

Continental Engine Models ..................................................................................20

Cummins Engine Models .....................................................................................20

October 2018

Table of Contents

x S®Booms • Z®Booms Part No. 1268489GT

Hydraulic Specifications ................................................................................... 21

Hydraulic Relief Valves ........................................................................................ 21

Hydraulic and Drive Hub Fluid Capacities ........................................................... 24

Hydraulic Oil Specifications ................................................................................. 26

Hydraulic Hose and Fitting Torque Specifications ............................................... 29

Torque Procedure ................................................................................................ 30

Section 3 Maintenance Procedures .................................................................................. 32

Introduction .......................................................................................................... 32

Maintenance Schedule ........................................................................................ 34

Pre-Delivery Preparation Report.......................................................................... 35

Scheduled Maintenance Inspection Report - Quarterly or Frequent ................... 36

Scheduled Maintenance Inspection Report - Annual........................................... 37

Programmed Maintenance Inspection Report - Booms....................................... 38

Commissioning Procedures ............................................................................. 39

C-1 Perform 50 Hour Service............................................................................... 39

C-2 Perform Engine Maintenance – 50 Hours..................................................... 39

C-3 Perform 150 Hour Service............................................................................. 40

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Genie Hubarbeitsbühne Handbücher

Genie

Genie TZ-20 Einrichtungshandbuch

Genie

Genie S-60X Bedienungsanleitung

Genie

Genie S-105 Bedienungsanleitung

Genie

Genie GS-2669 RT Bedienungsanleitung

Genie

Genie Z-45/25 Bedienungsanleitung

Genie

Genie S-100HD Bedienungsanleitung

Genie

Genie TZ-50 Bedienungsanleitung

Genie

Genie GTH-1048 Bedienungsanleitung

Genie

Genie Z-45/22 Bedienungsanleitung

Genie

Genie Z-34/22 Bedienungsanleitung

Genie

Genie TZ-50 Bedienungsanleitung

Genie

Genie Z-30 Bedienungsanleitung

Genie

Genie Z-80/60 Installations- und Betriebsanleitung

Genie

Genie S-105 Bedienungsanleitung

Genie

Genie Z-51/30 Bedienungsanleitung

Genie

Genie TMZ-50/30 Bedienungsanleitung

Genie

Genie Z-45/25 Bedienungsanleitung

Genie

Genie Z-25/8 Bedienungsanleitung

Genie

Genie S-65 XC CE Bedienungsanleitung

Genie

Genie GTH-1056 Installations- und Betriebsanleitung

Genie

Genie GS-1530 Installations- und Betriebsanleitung

Genie

Genie Z-45/25 Einrichtungshandbuch

Genie

Genie S-120 Bedienungsanleitung

Genie

Genie TMZ-34/19 Bedienungsanleitung

Beliebte Hubarbeitsbühne Handbücher anderer Marken

JLG

JLG Skytrak 6036 Gebrauchs- und Pflegehandbuch

Terex

Terex Z80H-7733 Bedienungsanleitung

Terex

Terex Gyro 4020 Bedienungsanleitung

Terex

Terex Genie Z-51/30 J Bedienungsanleitung

LGMG

LGMG T65JE Bedienungsanleitung

Oshkosh Corporation

Oshkosh Corporation JLG H800AJ Gebrauchs- und Pflegehandbuch

Oshkosh

Oshkosh JLG 1500SJ Installations- und Benutzerhandbuch

Skyjack

Skyjack SJ30AJE Bedienungsanleitung

Oshkosh

Oshkosh JLG 800A Installations- und Benutzerhandbuch

Terex

Terex Genie Z-135/70 Bedienungsanleitung

Skyjack

Skyjack SJ 46AJ Bedienungsanleitung

Molift

Molift Quick Raiser 205 Bedienungsanleitung

Snorkel

Snorkel SL26RTE Kurzanleitung

Terex

Terex Genie Z-135/70 Installations- und Betriebsanleitung

Terex

Terex Genie ZX-135/70 Installations- und Betriebsanleitung

Oshkosh Corporation

Oshkosh Corporation JLG E300A Bedienungsanleitung

Terex

Terex Genie GTH-3007 Bedienungsanleitung

Skyjack

Skyjack SJ45 T+ Bedienungsanleitung