Genius GE-R4 Bedienungsanleitung

GE-R4

MANUAL

1 2 3 4

Installation / User’s Guide

ATTENTION ELECTRICIAN

SEE WIRING DETAILS ON PAGES A-3

ADDITIONAL INFORMATION IN SECTION B

WIRING DIAGRAM

INDEX / WARRANTY

INSTALLATION

www.monitrol.com

WARNINGS AND PRECAUTIONS

Although the manufacturer has made every effort to ensure the accuracy of the information

contained herein, this document is subject to change without notice due to ongoing product

development.

WARNINGS AND PRECAUTIONS

Equipment, blown fuses and/or tripped breakers may prove harmful to the contents of the

building. Therefore it is strongly recommended to install backup devices. Spare equipment should

also be available at the owner’s site. Equipment manufactured by the manufacturer is protected

against normal line surges. High surges caused by thunder storms or power supply equipment

may damage this equipment. For added security against line voltage surges it is recommended

that surge and noise suppression devices be installed at the electrical distribution panel. These

devices are available from most electrical supply distributors.

RECOMMENDATIONS

The manufacturer recommends that all installation procedures described herein be performed by a

qualified electrician or installation technician. Further more the manufacturer recommends to test

all the functions, including the backup devices, after installation, after changes to the installation

and every month after that.

Fuse verification and replacement, as well as the proper setting of control values shall be the

responsibility of the owner of this equipment.

www.monitrol.com

GE-R4 WIRING DIAGRAM

GE-R4 Section A-3

Wiring Diagram

WIRING DIAGRAM GE-R4

WIRING DIAGRAM

Yanick Alain

GE-R4

13/04/07

DRAW

CONFIGURATION

WIR

/DIAGIC/GE-R4

FILE

REV

1265 A

GE-R4

L1 L2/N OUTPUT

COIL

SIGNAL

POWER

INPUT

STAGE 1

L1 L2/N OUTPUT

COIL

SIGNAL

POWER

INPUT

STAGE 3

L1 L2/N OUTPUT

COIL

SIGNAL

POWER

INPUT

STAGE 4

L1 L2/N OUTPUT

COIL

SIGNAL

POWER

INPUT

STAGE 2 NEUTRAL

FOR COILS

MASTER CONTROLLER

OUT 1

OUT 2

OUT 3

OUT 4

32 32 32

www.monitrol.com

GE-R4 WIRING DIAGRAM

GE-R4

Section A-4

GE-R4

Electrician’s notes

wiring tips and hints (see guide for details)

HIGH VOLTAGE WIRE INSTALLED ACCORDING TO LOCAL WIRING CODE.

THE CURRENT SHALL NOT EXCEED 25A, 3HP AT EACH OUTPUT (OUT).

MAXIMUM 2 WIRES OF SAME SIZE PER BLACK TERMINAL, NO BIGGER

THAN AWG #12, NO SMALLER THAN AWG #22.

www.monitrol.com

GE-R4 INSTALLATION

GE-R4

Section B-5

This section will inform the electrician on proper wiring and installation procedures for

the GE-R4.

The manufacturer recommends that the following installation instructions be followed to

as closely as possible, and that all work be performed by a certified electrician. Failure to

do so may void the warranty.

Description

The GE-R4 is designed to drive four stages of up to 25A under the control of a master

control system resulting in a clean air environment for your livestock.

It provides you with automated control over its four stages via the use of the master

control or alternatively by manual switch.

It will also keep you constantly informed of its four stages via LED indications. As the

LED will be lighted when the output is activated.

Unpacking

Unpack the GE-R4 and inspect contents for damage. Should the contents appear to be

damaged, contact your local distributor to return the material.

The package should contain the following standard items:

1 GE-R4 module

4 Bracket / 4 screws

1 Spare fuse

1 Installation / User’s Guide

Mounting Hardware Required

This is the list of the mounting hardware needed, which is not included with the product:

4 screws (to hang the unit onto the wall)

Screwdrivers

Soldering iron kit or approved sealed connectors

www.monitrol.com

GE-R4 INSTALLATION

GE-R4

Section B-6

General installation guidelines

GE-R4 Module

- It is recommended to install the module unit in a hallway to limit the GE-R4 exposure

to noxious gases.

- In order to avoid condensation problems inside the module, it is recommended to

install the GE-R4 on an inside wall. If it is not possible, use spacers to have an air gap

between the wall and the GE-R4.

- It is required to install the GE-R4 right side up with the cable entry holes facing

down.

- The enclosure is watertight, but do not spray water or submerge the GE-R4 in water.

Cover it carefully with plastic when cleaning the room.

- The GE-R4 should be installed in easy-access location but away from damaging

elements (heat, cold, water, direct sunlight, …).

- Do not drill the face, the side, the top or the underside of the control.

- Do not install the GE-R4 module near high-voltage equipment, power supply or

transformer.

Electrical Cables

- All electrical cables must be installed according to local wiring codes.

- Use separate conduits for the low voltage cables (communication) and the high

voltage cables. There must be at least 30 cm (1 foot) between low-voltage and high-

voltage conduits.

- If a low voltage cable has to cross over a high voltage cable, make this crossing at

90°.

- It is prohibited to use overhead cables outside the building.

Electrical Power

- Protection from electrical surges should be included in the planning of each

installation.

- Every module should have a separate breaker to avoid possible problem.

www.monitrol.com

GE-R4 INSTALLATION

GE-R4 Section B-7

Mounting

- The enclosure must be mounted in a location that will allow the cover to be

completely opened right up against the wall.

- Fasten the four brackets to the four mounting holes on the back of the enclosure,

using the four screws provided with the brackets.

- Then mount the enclosure on the wall by inserting screws through the brackets’

adjustment slots, into the wall. Make sure to position the enclosure so that all wires

extends out of the bottom section of the enclosure.

- The bracket slots also serve to adjust the position of the controller.

- Once you have adjusted the controller position, tighten the four mounting screws. (see

figure 1).

FIGURE NO. 1 Mounting Position and Devices

www.monitrol.com

GE-R4 INSTALLATION

GE-R4

Section B-8

Layout Board

FIGURE NO. 2 GE-R4 Electronic module Board

L1 L2/N

STAGE 1

OUTPUT

POWER

INPUT

COIL

SIGNAL

L1 L2/N

STAGE 2

OUTPUT

POWER

INPUT

COIL

SIGNAL

NEUTRAL

FOR COILS

L1 L2/N

STAGE 3

OUTPUT

POWER

INPUT

COIL

SIGNAL

L1 L2/N

STAGE 4

OUTPUT

POWER

INPUT

COIL

SIGNAL

www.monitrol.com

GE-R4 INSTALLATION

GE-R4 Section B-9

Powering Up Procedure

Verify all Connections

Once the GE-R4 is properly mounted on the wall and all modules to the terminal block,

perform the following steps:

- Ensure the flat cable between the bottom electronic board and the faceplate electronic

board is properly connected.

- Seal all cable entry holes.

Hermetically Close the GE-R4

Close the front panel and the lower access cover.

Put the power on

Secure the front panel with a lock

Using the toggle switches

The toggle switches permit the stage to be set in one of three modes as follows:

OFF To turn the stages permanently off, set the toggle switches to the OFF

position.

ON To turn the stages continually on, set the toggles switches to the ON position.

AUTO To allow the stages to operate under the master control, set the toggles

switches to the AUTO position.

Output LED

The output LED indicates if power is present at the stage output either in auto or manual

mode.

Changing fuse

The fuse protects the relay coil from any surge or over voltage. Remove stage input

power and coil signal power before changing a fuse.

Troubleshooting

Set the toggle switches on the GE-R4 to ON.

Are the outputs operating?

If not, verify the power connections to the GE-R4, fuses and connections to the outputs

(i.e. Fans).

www.monitrol.com

GE-R4 INSTALLATION

GE-R4

Section B-10

Specifications Module GE-R4

DESCRIPTION VALUE

Storage temperature -4°F to 131°F (-20°C to 55°C)

Operating temperature 32°F to 122°F (0°C to 50°C)

Humidity 90% maximum Non-condensing

Weight 2 lbs. (0.9Kg)

Size 11” x 17” x 5.5” (27.9 cm x 43.2 cm x 14 cm)

Norms CSA (NRTL/C)

Protection index IP 54 (dust and splashing water)

Warranty 2 years

RELAY OUTPUT

Maximum Load For Stages 1 -4 1HP @ 120VAC,

3HP @ 240VAC,

25A @ 250VAC resistive

Important Notice.

- Low-voltage and high-voltage wire must be passed through different conducts at

least 1 foot (30 cm) apart. If low-voltage and high-voltage conduits must be

crossed, the crossing must be at a 90-degree angle.

- All wiring must be made by a certified electrician and conform to local electrical

regulations.

www.monitrol.com

Inhaltsverzeichnis

Andere Genius Controller Handbücher

Genius

Genius A453 Technisches Handbuch

Genius

Genius SPRINT 382 Bedienungsanleitung

Genius

Genius BRAIN 04 Bedienungsanleitung

Genius

Genius BRAIN 15 Bedienungsanleitung

Genius

Genius Hub kit Bedienungsanleitung

Genius

Genius Brain 17 Bedienungsanleitung

Genius

Genius JA487C Technisches Handbuch

Genius

Genius JA382 Technisches Handbuch

Genius

Genius JA383 Technisches Handbuch

Genius

Genius BRAIN 06 24V Bedienungsanleitung

Genius

Genius GSM MOBILE STARTER Bedienungsanleitung

Genius

Genius JA277K Bedienungsanleitung

Genius

Genius JA510C Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch