Genius Sierra 800 Bedienungsanleitung

The instructions are split into two sections: RECESS INSTALLATION, PAGE 2, and

SURFACE INSTALLATION, PAGE 6. Determine which you need before starting.

If you ordered a custom made screen skip directly to step 3.

INSTALLATION TOOLS

SCREENED PORCH • GAZEBOS • GARAGE OPENINGS

INSTALLATION INSTRUCTIONS

SIERRA 800

IT IS HIGHLY RECOMMENDED THAT THE INSTRUCTIONS BE READ THROUGH BEFORE INSTALLATION.

GENIUS SIERRA 800 INSTRUCTIONS • PART NUMBER : 50-00094-0-0-0320

PHILLIPS SCREWDRIVER MEASURING TAPE HAND-HELD OR POWER SAW POWER DRILL & BITS RUBBER MALLET

Use saw

blade suitable

for cutting

aluminum.

NEEDLE PLIERS PENCIL OR PEN

PAGE 2

SIERRA 800

RECESS INSTALLATION

PART DESIGNATIONS

AScreen Cassette Assembly

BInside Rails

COutside Rails

DPull Bar

EPull Bar End Caps

FEnd Cap with Spring

GEnd Cap with Chain

HTension Device

IRecess Mount Clips

JWeatherstrip

KFoot Release Lever

LPull Bar Locks

OWeight Bar

P#8 x 3/4” (19mm) Panhead Screw

Q#6 x 3/8” (9mm) Phillips Panhead Screw

Record your opening measurements on the chart below to calculate your

measurements.

Cut all parts to length using the calculations above.

Keep the plastic ﬁlm on the cassette until all cuts are completed.

MEASURING AND CUTTING

Determine the maximum opening height & width for mounting your

screen, as shown below. Check for interference with any door or window.

Width

SIERRA 800 INSTALLATION INSTRUCTIONS PAGE 3

RECESS INSTALLATION

JAMB JAMB

OPENING WIDTH

TOP VIEW

SIDE VIEW

HEAD

INSIDE

OUTSIDE

OUTSIDE INSIDE

I-RECESS MOUNT CLIP

OPENING HEIGHT

SILL or FLOOR

IMPORTANT

Be sure to make

smooth, straight cuts. Only

cut the A-Screen Cassette

Assembly on the end

without the G-End Cap with

Operating Wand.

Height

OPENING WIDTH

LESS 7/8" TO ALLOW

FOR END CAPS

CASSETTE LENGTH (A)

= "

OPENING HEIGHT

LESS 2-1/8" TO ALLOW

FOR CASSETTE END CAPS

AND RECESS MOUNT CLIPS

INSIDE & OUTSIDE RAIL

LENGTHS (B & C)

= "

– 7/8"

– 2 1/8"

If you ordered a custom made screen skip directly to step 3.

SIERRA 800 INSTALLATION INSTRUCTIONS PAGE 4

RECESS INSTALLATION

PREPARING THE SCREEN CASSETTE

Insert F-End Cap with Spring into the correct end of the A-Screen Cassette

Assembly [Fig 2A] (the assembly will only ﬁt correctly in one end). Make sure to

line up the spring and bushing notches with one of the small slots in the center

screen tube. Wind the spring clockwise the number of turns designated in the fol-

lowing chart and push the F-End Cap with Spring in place on the A-Screen Cas-

sette Assembly. A rubber mallet is helpful to fully seat the F-End Cap with Spring.

Note that the spring in the cassette is for tension only. You will need to raise and

lower the screen by using the G-End Cap with Operating Wand.

SIDE VIEW

HEAD

OUTSIDE INSIDE

I-Recess Mount Clip

OPENING WIDTH

36”- 72”

73”-120”

120”-140”

140”-192”

SPRING TENSION

OPPOSITE END OF CARTRIDGE

Test Operating Wand (see page 10) for smooth operation. If it’s too tight, loosen

allen screw on the G-End Cap with Operating Wand. Insert the G-End Cap with

Operating Wand into A-Screen Cassette Assembly and push into place.

Slide one piece of the J-Weatherstrip into bottom slot of D-Pull Bar and the

other piece into the top of A-Screen Cassette Assembly. The M-Weight Bars are

already inserted inside the D-Pull Bar. Now insert the E-Pull Bar End Caps into

ends of D-Pull Bar [Fig 2B].

MOUNTING THE SCREEN CASSETTE

Mount the I-Recess Mount Clips to the inside of opening. When installed, the clips

will be centered above the cassette. Install a N-#8x3/4” (19mm) Panhead Screw

into the center of the slot to allow front to back adjustment [Fig 3].

Snap the A-Screen Cassette Assembly into place. Secure the A-Screen Cassette

Assembly in place by screwing the F-End Cap and G-End Cap to the side jamb of

the opening. The I-Recess Mount Clips and A-Screen Cassette Assembly may be

reversed to face toward the inside or outside of an opening depending upon which

side the Operating Wand needs to be accessible.

NOTE: the I-Recess Mount Clips lower the A-Screen Cassette Assembly in the

opening by 1/4”. The same 1/4” gap should be left above the F & G-End Caps to

avoid bowing the cassette.

SIERRA 800 INSTALLATION INSTRUCTIONS PAGE 5

RECESS INSTALLATION

FOOT RELEASE LEVER

The K-Foot Release Lever is an optional feature that makes it easier

to slightly rotate the D-Pull Bar in order to disengage the L-Pull Bar

Locks [Fig 4C] without bending over. Before installing, position the

K-Foot Release Lever 16" to 20" from the end of the D-Pull Bar on

the side closest to the Operating Wand. Attach the K-Foot Release

Lever to the D-Pull Bar using two O-#6 x 3/8” (9mm) Phillips

Panhead Screws.

LEFT

RIGHT

Windy conditions may affect the performance of a retractable screen. Retract the

screen in windy circumstances, during inclement weather, when not needed to

support immediate ventilation or during prolong periods when not used.

INSTALLING SIDE RAILS

Install the L-Pull Bar Locks at the bottom of each B-Inside Rail. Be sure that

the L-Pull Bar Locks can engage the D-Pull Bar as shown [Fig 4C]. Slide both

C-Outside Rails onto the tabs protruding from the F and G-Cassette End Caps

[Fig 4A]. Attach to jamb with N-#8x3/4” (19mm) Panhead Screws. Press B-

Inside Rails into C-Outside Rails [Fig 4B] with the shorter pile to the inside [Fig

4D] until they are evenly seated.

Using the height adjustment wheels on the L-Pull Bar Locks, adjust the height

to the appropriate level so they easily engage the D-Pull Bar. When correctly

adjusted, the latching and unlatching should be smooth and easy.

Shorter Pile 4D

See page 10 for Operating Wand Instructions.

5INSTALL THE TENSION DEVICE

Go to page 10.

PAGE 6

SIERRA 800

SURFACE INSTALLATION

PART DESIGNATIONS

AScreen Cassette Assembly

BInside Rails

DPull Bar

EPull Bar End Caps

FEnd Cap with Spring

GEnd Cap with Chain

HTension Device

JWeatherstrip

KFoot Release Lever

LPull Bar Locks

MSurface Mount ‘L’ Clips

NScrew Cover Caps

OWeight Bar

PP-#8 x 3/4” (19mm) Panhead Screw

Q#6 x 3/8” (9mm) Phillips Panhead Screw

Record your opening measurements on the chart below to calculate your

measurements.

Cut all parts to length using the calculations above.

Keep the plastic ﬁlm on the cassette until all cuts are completed.

MEASURING AND CUTTING

Determine the maximum opening height & width for mounting your

screen, as shown below. Check for interference with any door or window.

Width

SIERRA 800 INSTALLATION INSTRUCTIONS PAGE 7

SURFACE INSTALLATION

GARAGE DOOR JAMB GARAGE DOOR JAMB

OPENING WIDTH

TOP VIEW

SIDE VIEW

GARAGE DOOR HEAD

OPENING HEIGHT

INSIDE

OUTSIDE

M-SURFACE MOUNT ‘L’ CLIP

SILL or FLOOR

Height

OPENING WIDTH

LESS 7/8" TO ALLOW

FOR END CAPS

CASSETTE LENGTH (A)

= "

OPENING HEIGHT

LESS 2-1/8" TO ALLOW

FOR CASSETTE END CAPS

AND SURFACE MOUNT CLIPS

INSIDE & OUTSIDE RAIL

LENGTHS (B & C)

= "

– 7/8"

– 2 1/8"

IMPORTANT

Be sure to make

smooth, straight cuts. Only

cut the A-Screen Cassette

Assembly on the end

without the F-End Cap with

Operating Wand.

If you ordered a custom made screen skip directly to step 3.

SIERRA 800 INSTALLATION INSTRUCTIONS PAGE 8

SURFACE INSTALLATION

SIDE VIEW

GARAGE DOOR HEAD

OPENING HEIGHT

OUTSIDE

M-SURFACE MOUNT ‘L’ CLIP

SILL or FLOOR

MOUNTING THE SCREEN CASSETTE

Slide the K-Surface Mount ‘L’ Clips into the top of the A-Screen Cassette.

The clips should be evenly spaced along the A-Screen Cassette Assembly. Make

sure cassette is level and then screw clips in place with using a P - #8x3/4”(19mm)

Panhead Screw.

OPENING WIDTH

36”- 72”

73”-120”

120”-140”

140”-192”

SPRING TENSION

OPPOSITE END OF CARTRIDGE (SEE PAGE 10)

Test Operating Wand for smooth operation. If it’s too tight, loosen allen screw

on the F-End Cap with Operating Wand. Insert the F-End Cap with Operating

Wand into A-Screen Cassette Assembly and push into place.

Slide one piece of the H-Weatherstrip into bottom slot of C-Pull Bar. The

M-Weight Bars are already inserted inside the hollow of the C-Pull Bar. Now insert

the D-Pull Bar End Caps into ends of C-Pull Bar [Fig 2B].

PREPARING THE SCREEN CASSETTE

Insert E-End Cap with Spring into the correct end of the A-Screen Cassette

Assembly [Fig 2A] (the assembly will only ﬁt correctly in one end). Make sure to

line up the spring and bushing notches with one of the small slots in the center

screen tube. Wind the spring clockwise the number of turns designated in the

following chart and push the E-End Cap with Spring in place on the A-Screen

Cassette Assembly. A rubber mallet is helpful to fully seat the E-End Cap with

Spring. Note that the spring in the cassette is for tension only. You will need to

raise and lower the screen by using the F-End Cap with Operating Wand.

Remove the H-Weatherstrip from the groove at the back of the A-Screen

Cassette Assembly. This weatherstrip is not used in a surface mount

application [Fig 2A].

SIERRA 800 INSTALLATION INSTRUCTIONS PAGE 9

SURFACE INSTALLATION

LEFT

RIGHT

Windy conditions may affect the performance of a retractable screen. Retract the

screen in windy circumstances, during inclement weather, when not needed to

support immediate ventilation or during prolong periods when not used.

FOOT RELEASE LEVER

The I-Foot Release Lever is an optional feature that makes it easier to slightly

rotate the C-Pull Bar in order to disengage the J-Pull Bar Locks [Fig FIG 4C]

without bending over. Before installing, position the I-Foot Release Lever 16" to

20" from the end of the C-Pull Bar on the side closest to the Operating Wand.

Attach the I-Foot Release Lever to the C-Pull Bar using two O-#6 x 3/8” (9mm)

Phillips Panhead Screws.

INSTALLING SIDE RAILS

Install the J-Pull Bar Locks at the bottom of each B-Inside Rail. Be sure that

the J-Pull Bar Lock can engage the C-Pull Bar as shown in image [Fig 4C]. Slide

B-Inside Rails onto the tabs protruding from the E and F-Cassette End Caps, with

the shorter pile to the inside [Fig 4D]. Use an 1/8” drill bit and ﬁrst drill through both

sides of the B-Inside Rails where they are to be fastened. Next, using a 3/8” bit, drill

through the outside face only. This will allow you to snap the L-Screw Cover Caps in

place. Square and attach B-Inside Rails with N-#8 x 3/4” (19mm) Phillips Pan-

head Screws. Install L-Screen Cover Caps into each hole in the B-Inside Rails.

Using the height adjustment wheels on the J-Pull Bar Locks, adjust the height

to the appropriate level so they easily engage the C-Pull Bar. When correctly

adjusted the latching and unlatching should be smooth and easy.

Shorter Pile 4D

See page 10 for Operating Wand Instructions.

5INSTALL THE TENSION DEVICE

Go to page 10.

SIERRA 800 TENSION DEVICE

INSTALLATION

PAGE 10

Plunger

PARTS LIST

Chain Tension Device and #8 x 3/4 Phillips Panhead Screw

Depress the plunger with your ﬁngers and slide the Tension Device down to the

bottom of the chain.

IMPORTANT: When mounting tension device to a wood or metal surface, provided

screws can be driven directly into the mounting surface. When mounting tension

device to drywall, use anchors or fasteners that are designed for such substrates.

Consult your hardware store, building materials retailer, or supplier for guidance

on appropriate anchors or fasteners for your substrate.

Ensure the chain is not tangled or twisted.

RECESS MOUNT INSTALLATIONS

With the narrow end up, pull down on the Tension Device until the Plunger is

compressed half way. With the Plunger compressed, place the Tension Device

against your frame as shown and make a mark through the two screw holes.

SURFACE MOUNT INSTALLATIONS

With the narrow end up, pull down on the Tension Device until the Plunger is

compressed half way. With the Plunger compressed, place the Tension Device

against your frame as shown and make a mark through the two screw holes.

If mounting to wood or metal, drill holes through your marks with a 1/8” drill

bit. Then secure the Tension Device using the provided Phillips panhead screws.

If mounting the tension device to drywall, use anchors or fasteners appropriate

for the mounting substrate and follow anchor or fastener manufacturer’s

instructions.

Andere Handbücher für Sierra 800

Inhaltsverzeichnis

Andere Genius Projektionsfläche Handbücher

Genius

Genius Sierra 800 Bedienungsanleitung

Beliebte Projektionsfläche Handbücher anderer Marken

Draper

Draper E Series Handbuch

Elite Screens

Elite Screens Elite Tripod Series Bedienungsanleitung

Laarhoven

Laarhoven Companion II Bedienungsanleitung

Renogy

Renogy RMS-LFPS-US Bedienungsanleitung

Da-Lite

Da-Lite ExecutiveElectrol Bedienungsanleitung

Samsung

Samsung S*H65* Bedienungsanleitung

FONESTAR

FONESTAR PPTR-43100-FA Bedienungsanleitung

Slide Clear

Slide Clear Varro XL Bedienungsanleitung

Elite Screens

Elite Screens M85XWS1-SRM Bedienungsanleitung

OS РХ-090Н Bedienungsanleitung

Niko

Niko 10-845 Bedienungsanleitung

Speaka Professional

Speaka Professional 2357532 Betriebsanleitung

Sima

Sima XL-72 Bedienungsanleitung

Jasic

Jasic EVO 2.0 ET-200P Bedienungsanleitung

Elite Screens

Elite Screens Starling 2 Series Bedienungsanleitung

InFocus

InFocus SC-WALL GRY-92H Handbuch

Barco

Barco OverView MVL-615 Bedienungsanleitung

Draper

Draper Envoy Handbuch