GeoVision GV-AS1620 Bedienungsanleitung

GV-AS1620 Controller

Before attempting to connect or operate this product, please

read these instructions carefully and save this manual for future use.

User’s Manual

AS1620V10-A

Under the copyright laws, thismanual may not be copied, inwhole or inpart,

without the written consent of GeoVision.

Every effort has been made to ensure that the information in this manual is

accurate. GeoVision, Inc. makes no expressed or implied warranty of any kind

and assumes no responsibility for errors or omissions. No liability is assumed

for incidental or consequential damages arising from the use of the information

or products contained herein. Features and specifications are subject to

change without notice.

Note: No memory card slot or local storage function for Argentina.

GeoVision, Inc.

9F, No. 246, Sec. 1, Neihu Rd.,

Neihu District, Taipei, Taiwan

Tel: +886-2-8797-8377

Fax: +886-2-8797-8335

http://www.geovision.com.tw

Trademarks used inthis manual: GeoVision, the GeoVision logo and GV

series products are trademarks of GeoVision, Inc. Windows is a

registered trademark of Microsoft Corporation.

October 2019

Contents

Optional Devices ...................................................................................................... ii

Chapter 1 Introduction ............................................................................................ iii

1.1 Key Features.................................................................................................... iii

1.2 System Requirements...................................................................................... iii

1.3 Packing List ..................................................................................................... iii

1.4 Overview.......................................................................................................... iv

Chapter 2 Installing on a Network........................................................................... 3

2.1 Checking the Dynamic IP Address................................................................... 4

2.2 Configuring the Static IP Address..................................................................... 5

2.3 Configuring DDNS Connection......................................................................... 5

Chapter 3 The Web Interface .................................................................................. 9

3.1 Basic Settings .........................................................................................................10

3.1.1 System Setup...............................................................................................10

3.1.2 Firmware Update..........................................................................................12

3.1.3 Security Configuration..................................................................................13

3.2 Advanced Settings ..................................................................................................13

3.2.1 Function Configuration .................................................................................14

3.2.2 Parameter Configuration ..............................................................................17

3.2.3 Time Configuration.......................................................................................19

3.2.4 Input Configuration.......................................................................................20

3.2.5 Output Configuration ....................................................................................20

3.2.6 Log Viewer ...................................................................................................21

3.2.7 System Log Viewer ......................................................................................21

3.3 Extended Device.....................................................................................................22

Chapter 4 Troubleshooting................................................................................... 23

Optional Devices

Optional devices can expand the capabilities and versatilities of your controller. Consult our

sales representative for more information.

GV-CR420

GV-CR420 is a card reader with a built-in 4MP wide angle IP camera. The card

reader recognizes identification cards and transmits live view through network

connection.

GV-CR1320

GV-CR1320 is a card reader with a built-in 2MP wide angle IP camera. The card

reader recognizes identification cards and transmits live view through network

connection.

GV-DFR1352

GV-DFR1352 is a card reader that uses a 13.56 MHz frequency. The reader has

both Wiegand and RS-485 outputs that can be connected to any standard access

control panel.

GV-FWC

GV-FWC can integrate GV-Face Recognition Cameras (GV-FD8700-FR / GV-

VD8700) into access control systems by sending access card data, paired to Face

IDs, to controllers either through TCP/IP or Wiegand connection.

GV-FR2020 GV‐FR2020 is a 13.56 MHz face recognition reader. The reader supports two

operation modes for access control: Face Recognition and Card.

GV-IB25 / 65 / 85

Infrared Button

The GV‐IB25 / 65 / 85 Infrared Button detects infrared movement within 3 to 12 cm

and allows you to open the door with a wave of hand.

GV-Reader 1251

GV-Reader 1251 is a card reader that uses a 125 kHz frequency. The reader has

both Wiegand and RS-485 outputs that can be connected to any standard access

control panel.

GV-R1352

GV-R1352 is a card reader that uses a 13.56 MHz frequency. The reader has both

Wiegand and RS-485 outputs that can be connected to any standard access

control panel.

GV-RK1352

GV-RK1352 is a card reader with keypad that uses a 13.56 MHz frequency. The

reader has both Wiegand and RS-485 outputs that can be connected to any

standard access control panel.

GV-RU9003

GV‐RU9003 is a Radio Frequency Identification (RFID) reader of ISO 18000‐6C

(EPC GEN2) standard. Designed for parking lot management, the reader can read

RFID tag within 10 m (32.8 ft).

GV-SR1251 GV‐SR1251 is a card reader that uses a 125 kHz frequency. It has both Wiegand

and RS‐485 outputs that can be connected to any standard access control panel.

GV-GF

Fingerprint

Readers

GV-GF1921 / 1922 is a fingerprint reader, supporting three operation modes:

Fingerprint Only, Fingerprint + Card and Card Only. Readers with optical and

capacitance sensors are available.

GV-AS ID Card /

Key Fob & GV-

UHF Tag

GV-AS ID Card and GV-AS ID Key Fob are ideal for business and residential

environment, where access control is important for security reasons. 125 KHz and

13.56 MHz cards and key fobs are available. GV-UHF Tag is ideal for parking lot

management. 900 MHz UHF Tag is available.

GV-POE Switch

The GV‐POE Switch is designed to provide power along with network connection

for IP devices. The GV‐POE Switch is available in various models with different

numbers and types of ports.

GV-WTR

GV-WTR is a converter designed to support Wiegand interface to RS-485

interface, thereby enabling 3rd party readers to be connected to RS-485 GV-

Controllers. Through the GV-WTR, Wiegand-interface readers can be easily

combined to access control systems for improved versatility.

Electric Lock Three types of electric locks are available: electromagnetic lock, electric bolt and

electric strike.

Power Adapter Contact our sales representatives for the countries and areas supported.

Push Button

Switch

The push button switch can be integrated with access control system, allowing

door exit by momentarily activating or deactivating the electric locking device. Both

American standard and European standard push buttons are available.

Introduction

Chapter 1 Introduction

GV-AS1620 is a single door controller with three types of interfaces, Wiegand, RS-485 and

TCP/IP, to accommodate various readers for entry and exit management. Through its I/O

pins, it provides not only basic door operations but also alarm, tamper and fire senor

applications, as well as allowing LEDs connected to indicate an access granted and denied.

1.1 Key Features

One door IP controller (entry and exit)

3 types of interfaces, Wiegand, RS-485 and TCP/IP, supporting 2 readers for each

interface.

4 digital inputs for door contact, exit button, fire contact and tamper contact

4 relay outputs for lock, alarm, 2 LED for an access granted and access denied

DC 12V, 3A / PoE+ (IEEE 802.3at)

Suitable for door, parking lot and elevator controls

Stores up to 100,000 cards

1.2 System Requirements

GV-ASManager V5.2.0 or later

1.3 Packing List

1. GV-AS1620

2. Warranty Card

3. Download Guide

1.4 Overview

Figure 1-1

Pin Definition Pin Definition Pin Definition

DO 1 Lock DI 1 Door Contact Wiegand A Entry Reader

DO 2 Alarm DI 2 Exit Button Wiegand B Exit Reader

DO 3 LED for Access Granted DI 3 Fire Contact RS-485 +/- RS-485 Readers

DO 4 LED for Access Denied DI 4 Tamper Contact

Control Definition

DC 12V Power output for compatible devices connected

Web Setting

Switch

GUI security lock. Switch on to lock all system configurations on the Web interface of the

controller.

Default Button Reset the controller to factory default if it is not functioning correctly. To do this, hold down

the Default button with a pointy object such as the tip of a pen for 3 to 5 seconds.

Installing on a Network

Chapter 2 Installing on a Network

Through network connection, you can access the Web interface of the controller and

connect it to GV-ASManager for more comprehensive management. There are three ways

to set up the controller on network.

1. By default, when the controller is connected to a network with a DHCP server, a

dynamic IP address will be assigned to the controller. See 2.1 Checking the Dynamic IP

Address to look up its IP address.

2. When the DHCP server on your network is unavailable or disabled, the controller is

accessible by its default IP address 192.168.0.100. See 2.2 Configuring the Static IP

Address.

3. You may also use a DDNS (Dynamic Domain Name System) server to access the

controller. For details on domain name service, see 2.3 Configuring DDNS Connection.

2.1 Checking the Dynamic IP Address

Follow the steps below to look up the IP address and access the Web interface of the

controller.

1. Download and install GV-IP Device Utility from our website.

2. On the GV-IP Utility window, click the button to search for the IP devices connected

in the same LAN.

3. Click the Name or Mac Address column to sort.

4. Find the controller with its MAC address, click on its IP address and select Web Page.

Figure 2-1

5. When the login dialog box appears, type the default admin for both username and

password and click OK to log in.

Note: The PC installed with GV-IP Device Utility must be under the same LAN as the

controller you wish to configure.

Installing on a Network

2.2 Configuring the Static IP Address

By default, the controller uses a DHCP connection. However, you can follow the instructions

below to configure a static IP address.

1. Open an Internet browser, and type the default IP address https://192.168.0.100 or the

dynamic IP address. The login dialog box appears.

2. Type default value admin for both username and password, and click OK. This page

appears.

Figure 2-2

3. In the DHCP Client section, select Disable. Type the static IP address information,

including IP Address, Subnet Mask, Default Gateway and Domain Name Server.

4. Click Submit. When the setting is complete, the Status field will indicate Register

Success. Then the controller can be accessed with this fixed IP address.

2.3 Configuring DDNS Connection

DDNS (Dynamic Domain Name System) provides another way of accessing the controller

when using a dynamic IP. DDNS assigns a domain name to the controller, so GV-

ASManager can always access the controller by using a static domain name. The controller

supports two DDNS services: GeoVision DDNS Server and Dynamic Network Services Inc.

(DynDNS).

To enable the DDNS function, you first should register a domain name from one of the two

supported DDNS service provider’s websites.

Figure 2-3

2.3.1 Registering a DDNS Domain Name

To obtain a domain name from the GeoVision DDNS Server:

1. Click the GeoVision DDNS button on the Network Configuration page (Figure 2-2). Or

open an Internet browser, and type the Web address http://ns.gvdip.com/register.aspx.

The GV-Dynamic DNS Service V2 page appears.

Note:

1. Dynamic DNS uploads IP addresses over the Internet through ports 80 and 81. If your

controller is connected behind a router or firewall, make sure ports 80 and 81 are

enabled. Dynamic DNS will only upload global IP addresses. If your controller is using

virtual IP, NAT port mapping should be done first.

2. The DDNS service is provided purely as a favor to you. We hope it simplifies the process

of trying to connect an IP video device to the network. GeoVision does not and cannot

warrant that the DDNS service will be uninterrupted or error free. Please read Terms of

Service carefully before using the service.

Inhaltsverzeichnis

Andere GeoVision Controller Handbücher

GeoVision

GeoVision GV-AS1520 Bedienungsanleitung

GeoVision

GeoVision GV-AS1520 Bedienungsanleitung

GeoVision

GeoVision GV-AS Series Bedienungsanleitung

GeoVision

GeoVision GV-CS1320 Bedienungsanleitung

GeoVision

GeoVision GV-AS1520 Bedienungsanleitung

GeoVision

GeoVision GV-AS100 Bedienungsanleitung

GeoVision

GeoVision GV-AS1010 Bedienungsanleitung

GeoVision

GeoVision GV-AS210 Bedienungsanleitung

GeoVision

GeoVision GV-AS100 Bedienungsanleitung

GeoVision

GeoVision GV-AS200 Bedienungsanleitung

GeoVision

GeoVision GV-Control Center System V2 Bedienungsanleitung

GeoVision

GeoVision GV-VR605 Bedienungsanleitung

GeoVision

GeoVision GV-AS100 Handbuch

GeoVision

GeoVision GV-AS200 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung