Getnet GN-621U Bedienungsanleitung

publication may be reproduced, transmitted, transcribed, stored in a retrieval system,

or translated into any language or computer language, in any form or by any means,

electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the

prior written permission of this company.

This company makes no representations or warranties, either expressed or implied,

with respect to the contents hereof and specifically disclaims any warranties,

merchantability or fitness for any particular purpose. Any software described in this

manual is sold or licensed "as is". Should the programs prove defective following their

purchase, the buyer (and not this company, its distributor, or its dealer) assumes the

entire cost of all necessary servicing, repair, and any incidental or consequential

damages resulting from any defect in the software. Further, this company reserves the

right to revise this publication and to make changes from time to time in the contents

hereof without obligation to notify any person of such revision or changes.

The product you have purchased and the setup screen may appear slightly different

from those shown in this QIG. For more detailed information about this product, please

refer to the User's Manual on the CD-ROM. The software and specifications are

subject to change without notice. Please visit our web site www.getnet.com.tw for the

manual are trademarks and/or registered trademarks of their respective holders.

Federal Communication Commission

Interference Statement

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

4. Consult the dealer or an experienced radio technician for help.

FCC Caution

This device and its antenna must not be co-located or operating in conjunction with

any other antenna or transmitter.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and (2)

this device must accept any interference received, including interference that may

cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for

compliance could void the authority to operate equipment.

Federal Communication Commission (FCC) Radiation Exposure

Statement

This EUT is compliance with SAR for general population/uncontrolled exposure limits

in ANSI/IEEE C95.1-1999 and had been tested in accordance with the measurement

methods and procedures specified in OET Bulletin 65 Supplement C.

The equipment version marketed in US is restricted to usage of the channels 1-11

only.

R&TTE Compliance Statement

This equipment complies with all the requirements of DIRECTIVE 1999/5/EC OF THE

EUROPEAN PARLIAMENTAND THE COUNCIL of March 9, 1999 on radio

equipment and telecommunication terminal Equipment and the mutual recognition of

their conformity (R&TTE)

The R&TTE Directive repeals and replaces in the directive 98/13/EEC

(Telecommunications Terminal Equipment and Satellite Earth Station Equipment) As

of April 8, 2000.

Safety

This equipment is designed with the utmost care for the safety of those who install and

use it. However, special attention must be paid to the dangers of electric shock and

static electricity when working with electrical equipment. All guidelines of this and of

the computer manufacture must therefore be allowed at all times to ensure the safe

use of the equipment.

EU Countries Intended for Use

The ETSI version of this device is intended for home and office use in Austria,

Belgium, Denmark, Finland, France, Germany, Greece, Ireland, Italy, Luxembourg,

the Netherlands, Portugal, Spain, Sweden, and the United Kingdom.

The ETSI version of this device is also authorized for use in EFTAmember states:

Iceland, Liechtenstein, Norway, and Switzerland.

EU Countries Not intended for use

None.

CONTENTS

1INTRODUCTION.............................................................................1

1.1Features.........................................................................................................................1

1.2Specifications................................................................................................................1

1.3Package Contents..........................................................................................................2

2INSTALLATION PROCEDURE .....................................................3

3CONFIGURATION UTILITY .......................................................11

3.1Utility Overview ......................................................................................................... 11

3.2Available Network ......................................................................................................13

3.3General........................................................................................................................14

3.4Profile..........................................................................................................................15

3.4.1 Configure the Profile ....................................................................... 16

3.5Status...........................................................................................................................20

3.6Statistics......................................................................................................................20

3.7Wi-Fi Protect Setup (WPS).........................................................................................21

3.8Software AP................................................................................................................24

3.8.1 AP Properties Setting....................................................................... 25

3.8.2 AP Advanced................................................................................... 25

3.8.3 AP Statistics.................................................................................... 26

3.8.4 SoftAP ............................................................................................ 27

4TROUBLESHOOTING..................................................................28

1 Introduction

Thank you for purchasing this high-speed wireless network card! Excepting common wireless

standards 802.11b/g, this wireless network card is also able to access 802.11n wireless networks -

data transfer rate is 300Mbps*(Download speed only), and that’s three times faster than 802.11g

wireless network!

For WLAN security issues, this adapter supports 64/128-bit WEP data encryption that protects your

wireless network from eavesdropping. It also supports WPA (Wi-Fi Protected Access) feature

technology. Client users are required to authorize before accessing to APs or AP Routers, and the data

transmitted in the network is encrypted/decrypted by a dynamically changed secret key. Furthermore,

this adapter supports WPA2 function, WPA2 provides a stronger encryption mechanism through AES

(Advanced Encryption Standard), which is a requirement for some corporate and government users.

This adapter is cost-effective, together with the versatile features; it is the best solution for you to build

your wireless network.

1.1 Features

•Work with 802.11b/g/Draft-N wireless network devices.

•High-speed transfer data rate - up to 300Mbps( Download speed only ).

•High throughput supports multi-media data bandwidth requirement.

•Support 64/128-bit WEP Data Encryption, WPA, WPA2.

•Automatic fallback increases data security and reliability.

•Supports the most popular operating system: Windows 2000/XP/Vista.

•Supports USB 2.0 interface.

1.2 Specifications

•Standard: IEEE 802.11b/g/n

•Interface: USB 2.0 Type A

•Frequency Band: 2.4000 ~ 2.4835GHz (Industrial Scientific Medical Band)

•Data Rate:

11b: 1/2/5.5/11Mbps

11g: 6/9/12/24/36/48/54Mbps

11n (20MHz): MCS0-7 (up to 72Mbps)

11n (40MHz): MCS0-7 (up to 150Mbps)

•Security: 64/128-bit WEP Data Encryption, WPA, WPA2

•Antenna: Chip Antenna

•Drivers: Windows 2000/XP/Vista

•LEDs: Link/Activity

•Transmit Power: 11n: 14±1.5dBm, 11g: 14±1.5dBm, 11b: 17±1.5dBm

•Dimension: 10(H) x 19.5(W) x 56(D) mm

•Temperature: Operating 32~104°F (0 ~40°C), Storage -13~149°F (-25~65°C)

•Humidity: Max. 95% (NonCondensing)

•Certification: FCC, CE

1.3 Package Contents

Before you begin the installation, please check the items of your package. The package should include

the following items:

•One USB Adapter

•One CD (Driver/Utility/User’s Manual)

•One Quick Guide

If any of the above items is missing, contact your supplier as soon as possible.

2 Installation Procedure

Before you proceed with the installation, please notice following descriptions.

Note1: The following installation was operated under Windows XP. (Procedures are similar for

Windows 2000/Vista.)

Note2: If you have installed the Wireless PC Adapter driver & utility before, please uninstall the

old version first.

I. Install the Driver and Utility

A. Insert the Installation CD to your CD-ROM Drive. Select “ Language “ and “Setup.exe” program.

B. Select Setup Language and click “OK” to proceed.

C. Click “Next” to go to the next step.

D. Now you’ll see the following message, please click ‘Install’ to begin the installation.

E. The system starts to install the driver and utility.

F. Click “Finish” to complete the driver and utility installation.

Andere Handbücher für GN-621U

Inhaltsverzeichnis

Andere Getnet Adapter Handbücher

Getnet

Getnet GN-621U Bedienungsanleitung

Beliebte Adapter Handbücher anderer Marken

PCB Piezotronics

PCB Piezotronics 090B274 Bedienungsanleitung

Auvidea

Auvidea J20 Produkthandbuch

Gossen MetraWatt

Gossen MetraWatt AT3-III E Bedienungsanleitung

Akribis

Akribis ITF-21-BISS-MIT Bedienungsanleitung

Tenda

Tenda W54U Bedienungsanleitung

ROHO

ROHO AGILITY Bedienungsanleitung

PROLiNK

PROLiNK WN2001 Bedienungsanleitung

Hawking

Hawking HUF2 Bedienungsanleitung

Airlink101

Airlink101 AWLC4030 Bedienungsanleitung

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Bedienungsanleitung

Philips

Philips SWA4554S/10 Bedienungsanleitung

JVC

JVC TS-C9D2B Gebrauchsanweisung

NETGEAR

NETGEAR A6100 Bedienungsanleitung

D-Link

D-Link DWA-121 Bedienungsanleitung

Philips

Philips SWA2037 Bedienungsanleitung

Basalte

Basalte 0610-20 Bedienungsanleitung

Yealink

Yealink EHS40 Bedienungsanleitung

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Bedienungsanleitung