Geutebruck GSD-200 Bedienungsanleitung

MINISPEEDDOMECAMERA

MINI SPEED DOME CAMERA

UserMANUAL

GSD-200

TABLE OF CONTENTS

1. CATION ------------------------------------------------------- 3

2. INTRODUCTION OF PRODUCT -------------------------------5

1). DESCRIPTION AND FEATURES -----------------------------5

2). INSTALLING AND CONNECTING ---------------------------- 6

2-1. NAME AND FUNCTION OF EACH PART -------------------6

2-2. INSTALLATION --------------------------------------7

2-3. CONNECTION DIAGRAM --------------------------------8

3. DIRECTIONS FOR USE -----------------------------------------9

1). DIP SWITCH SETTING ---------------------------------------9

2). HOW TO CHANGE PROTOCOL -------------------------------10

3). HOW TO SET ADDRESS DIP SWITCHES ----------------------11

4). HOW TO USE OSD MENU ----------------------------------12

4-1. HOW TO CONTROL OSD MENU --------------------------12

4-2. FUNCTIONAL DESCRIPTIONS ON EACH MENU ------------13

4-3. SETTING FUNCTIONS BY KEYBOARD---------------------23

4-4. OSD MESSAGE DESCRIPTION ---------------------------27

4. TROUBLE SHOOTING ------------------------------------------29

5. DIMENSIONS & ASSEMBLES------------------------------------30

6. CONFIGURALTION ---------------------------------------------31

7. SPECIFICATIONS ----------------------------------------------33

1. CAUTION

Thank you for purchasing mini speed dome camera GMS-200.

Please operate the product after being fully aware of the manual.

Pease contact us if you have any queries or face any problems.

DO NOT CONTROL PAN, TILT BY FORCE

Do not move the inside Pan/Tilt motor by force

after removing dome cover.

It can cause damages.

HANDLE WITH CARE OF CAMERA LENS AND DOME

Be careful of handle with dome cover

Please use a soft fabric due to a scratch when you

clean the cover.

EXTERNAL SHOCK

Damages can be occurred through the carelessness

Or shock when you take out the module.

Dimensions

UNIT:mm

CAUTION IN USE.

Do not disassemble the unit and put alien substances in the unit.

It can cause troubles.

Ensure power switch-off before the installation.

Ensure power switch-off and check the voltage the camera before the installation.

Do not give the unit a shock and an operation.

Giving a strong shock or an excessive power on the button, terminal can cause troubles.

This product has been designed and manufactured in accordance with the harmonized European

standards, following the provisions of the below stated directives.

Electromagnetic Compatibility Directive 89/336/EEC(EN61000-3-2:1995, EN61000-3-3:1995,

EN50081-1:1992, EN50082-1:1997)

This devise complies with part 15 of the fcc rules operation is subject to the following two

conditions: (1) This device may not cause harmful interference and (2) This device must accept

any interference received including interference that may cause undesired operation

2. INSTRUCTION OF PRODUCT

1) DESCRIPTION AND FEATURES

- Description -

This camera has been designed elegantly for buildings, department stores that need to be

in harmony with the interior as a high speed dome camera, including various observation

functions. It moreover is effective for true Day & Night.

- Features -

High magnification zoom lens

Max 100 times zoom

(optical x10 zoom, digital x10 zoom)

Horizontal resolution min. 520 TVL

Color: min.520 TVL, B/W: min.570 TVL

horizontal resolution

Low light and Day & Night

The result of improving sensitivity

0.0007Lux (DSS Control)

ICR Day & Night allows the filter to change

B/W mode (0.1 Lux) in the night.

Additional functions

PTZ trace:

Memorize P/T/Z move for 120 seconds then

operate the registered trace.

Auto swing:

Repeat pan and tilt between two preset

positions.

Group:

12 Preset positions are chained in one Group.

(Max 12 Groups available)

Tour:

Max 12 Groups are bound.

410k Pixel CCD CAMERA

SONY CCD chip with high resolution and low

illumination condition.

250 Preset positions

A maximum of 250 preset positions can be

programmed. The preset function enables to set

where you want on monitor at any time.

4ch alarm inputs

It can be directly connected to sensor and used

with presets owing to built-in 4-channel

sensor input terminals.

It can be also operated together with other

equipment owing to built-in alarm output.

Auto Tilt move

The unit can track the object moving automatically

until 180° in vertical.

OSD (On Screen Display)

Provides character information displayed on the

monitor, such as the camera ID address,

camera name, preset number, sequence status,

and sets various functions of camera easily on

the OSD menu screen.

Privacy Zones

For the privacy, it can be programmed for

masking zone up to 4 locations on the

OSD menu screen.

Audio out (Option)

Built-in mono microphone without Amplifier.

2). INSTALLATION AND CONNECTION

2-1. NAME AND FUNCTION OF EACH PART

104 ¢ BUBBLE

CAMERA COVER

CAMERA BASE

P/T BASE

MAIN BASE

BOTTOM COVER

CAMERA BODY

CAMERA BODY COVER

2-2. INSTALLATION

Make 4 holes after attaching

ceiling guide where the

came

ra is set.

Take apart 4 bands of camera body

cover

Set up DIP switch

(Reference to XXP)

Connect with cables.

Tighten 4 screws. Attach the camera

body cover

Completion

Take out the cables

from the ceiling.

2-3. CONNECTION DIAGRAM

AC24V/500mA(GMS-200iS)

DC12V/1A (GMS-200S)

VIDEO IN AUDIO IN

CAMERA 1~128

DC JACK

RS-485 Sensor 1

4 ALARM INPUT

VIDEO INPUT Sensor 4

AUDIO

CAMERA 129

~CAMERA 255

Violet(N/O)

Gray(COM)

Black(GND)

Brown(CH1)

Red(CH2)

Yellow(CH3)

Green(CH4)

DIRECTIONS

FOR USE

1) DIP SWITCH SETTING

Set the camera numbers in the state of

ADDR, set communication speed, protocol

in the state of INIT.

-This part is each address of camera.-

It shows the status of Power

On/Off. Green LED is On while

power is alive. In the status of

operation, red LED is off.

-TERMINALATION RESISTOR (DIP SW NO1)

~Turn the last camera on the data line as a

switch to turn on/off the terminal resistor on.

Turn the DIP SW of some of the farthest

cameras on in the case of the data lines

distributed to several directions.

* The first default is off.

-ADDRESS/ INITIAL SELECT (DIP SW NO3)

~Set ADDRESS DIP SW in the status of ADDRESS

(*Reference to next page*)

(.*** The first default is ADDRESS.**)

-Set the communication speed and Protocol

(Demand for the technical inquiry) up in the

state of the INITAIL.

-Select PAL / NTSC system.

-POWER ON/OFF (DIP SW NO4)

Set DIP SW only in the status of Power off.

Then turn on the power after setting DIP SW.

2) HOW TO CHANGE PROTOCOL

Set up this part.

The switch that selects Protocol. The switch that selects Baud Rate.

Change No.3 at S2 to INIT if want to change Protocol.

①Please make Power off.

②Switch Protocol that wants to change on as above table.

③Make Power on, then set Protocol and Baud rate are appealed.

④Make Power off, if every setting is right. Then it is done.

⑤Change No.3 of S2 to ADDR before Power on, then make Power on after setting the

address of the camera.

⑥Try it again with the information as above the table, if something is wrong.

Inhaltsverzeichnis

Andere Geutebruck Sicherheitskamera Handbücher

Geutebruck

Geutebruck G-Cam/EWPC-2271 Bedienungsanleitung

Geutebruck

Geutebruck G-Cam/EWPC-5280 Bedienungsanleitung

Geutebruck

Geutebruck G-Cam/ESD-3401 Bedienungsanleitung

Geutebruck

Geutebruck G-Cam/EBC-3310 Bedienungsanleitung

Geutebruck

Geutebruck G-Cam/ANPR-49 Series Bedienungsanleitung

Geutebruck

Geutebruck G-Cam/EFD-3271 Bedienungsanleitung

Geutebruck

Geutebruck G-Cam/EFD-2251 Bedienungsanleitung

Geutebruck

Geutebruck EcoBC-1110 Bedienungsanleitung

Geutebruck

Geutebruck G-Cam/EBC-3141 Bedienungsanleitung

Geutebruck

Geutebruck G-Cam/EWPC-5240 Bedienungsanleitung

Geutebruck

Geutebruck Guardian 704 ILB Bedienungsanleitung

Geutebruck

Geutebruck G-Cam/EWPC-3270 Bedienungsanleitung

Geutebruck

Geutebruck G-Cam/EBC-5101 Bedienungsanleitung

Geutebruck

Geutebruck G-Cam/ANPR-49 Series Bedienungsanleitung

Geutebruck

Geutebruck G-Cam/EWPC-5280 Bedienungsanleitung

Geutebruck

Geutebruck G-Cam/ESD-4510 Bedienungsanleitung

Geutebruck

Geutebruck G-Cam/EWPC-5270 Bedienungsanleitung

Geutebruck

Geutebruck G-Cam/E2 Series Bedienungsanleitung

Geutebruck

Geutebruck G-Cam/EWPC-3285 Bedienungsanleitung

Geutebruck

Geutebruck GFD-632/VP-IR Bedienungsanleitung

Geutebruck

Geutebruck G-Cam EWPC-3210 Bedienungsanleitung

Geutebruck

Geutebruck 0.02491 Bedienungsanleitung

Geutebruck

Geutebruck G-Cam/EBC-2112 Bedienungsanleitung

Geutebruck

Geutebruck G-Cam/EHC-3181 Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung