GEZE GC 307+ Bedienungsanleitung

Technology Radar movement detector

Frequency 24,150 GHz

Power ux density < 5 mW/cm2

Radiated power < 20 dBm EIRP

Detection range (hand) ±10 … 60cm (movement towards

sensor, angle 90°), adjustable*

Type of detection Movement (independent of direction)

Speed of objects for

detection

Min. 5Hz or ±3cm/s,

max. 200Hz or ±1.2m/s

Power supply ** 12–24 V AC ±10 %

12–24 V DC +30 %/–10 %

Mains frequency 50 … 60 Hz

Power consumption < 1.5 W

Output

Changeover relay (potential-free contact)

àMax. contact voltage 42 V AC/DC

àMax. switching current 100 mA

Holding time 0.5s (in PULSE mode)

Temperature range –20 °C … +55 °C

Protection rating IP 65 (if front and seal are installed on

a smooth surface)

Material PC

Colour White

Recommended cable Braided cable up to 16 AWG – 1.5 mm2

* Adjustment of the detection eld < 10 cm is possible, but the detec-

tion capacity of the sensor can then no longer be guaranteed.

** The unit must be supplied by an approved SELV-limited current

source of Class II. This requirement is the need for double insulation

between primary voltages and the unit supply. The power supply

should be limited to 1.5 A.

The GC307+ can be installed behind tiles,

wood, plaster, plastic and glass.

Do not install the GC307+ behind metal-

lic surfaces.

Do not install the GC307+ in the swivel-

ling range of doors.

Avoid moving objects near the GC307+.

Intended use

The movement detector GC307+ may only be

used for the activation of automatic sliding, circular

sliding, folding, swing or revolving doors with GEZE

drives.

195727 (Hand Icon)

195751 (WC Icon)

193226 (Hand Icon)

195750 (WC Icon)

GC 307+

198725-00





GND

24V

GND

PA1A

PA1B

PA2

24V

PE1

PE2

PWR

OUT

GND

PWR

OUT

WC control

(Slimdrive EMD, Powerturn and sliding door drives)

Set the type of contact for KI and

KA to “normally open contact”.

Follow the instructions for the drive.

Push button

inside

Push button

outside

àSet “PE1” or “PE2” to “WC control”.

àSet “PA1” or “PA2” “Function” to “Exit only”.

àSet “PA1” or “PA2” “Function” to “WC control alarm”.

àSet “Hold-open times, 1-leaf opening” to the desired time (0-60s).

Range

àAdjust according to requirement.

àdepends on the direction of movement, size and material/

type of object to be detected.

60 cm

Output Signal

sound

DIP

123

Colour of LED

No detection Detection

DIP

123O Blue

Blue O

DIP

123

Blue Green

DIP

123

O Green

DIP

123

Green O

DIP

123

O O

DIP

123

Green Red

DIP

123

reen

DIP

123

Output mode

ntrol input

onnect the input to an external signal.

When the conta

ct is closed, the LED display lights up red.

oustic feedback

Pulse mode (NO):

Recommended for automatic

door applications

Pulse mode (NC)

Frequency modeToggle mode:

Recommended for switch

applications

On O

DIP

Output is still available.

The input signal must be a potential-free contact

(no voltage).

Input

LED after DIP switch conguration

DIP

Open the GC 307+

Setting using the remote control

Operation

After unlocking, the red LED ashes

and the sensor is accessible.

If the red LED ashes quickly after unlocking:

XEnter the access code.

If the access code is not known:

XTurn the power supply o and on again.

After switch-on the sensor can be unlocked

within 1minute without the access code being

entered.

XLock the sensor again at the end of the

settings.

Saving the access code

The access code (1 to 4 digits) is recommended for sensors which are close together.

Deleting the access code

Setting one or more parameters

Resetting to factory settings

Full reset

XEnter the

access code.

XSelect a parameter.

Range

60 cm

To change these settings by remote control, the range must be set to minimum.

10 2 3 4 5 6 7 8 9

small >>>>>>>>large

Output

Output conguration To change these settings by remote control, the DIP switches “Output” must be set

to OFF.

Pulse NO

Toggle

Pulse NC

Frequency

Holding time

0.5 s

1 2 3 4 5

1 s 2 s 3 s 4 s 5 s

LED

Colour of LED

No detection Detection

O Blue

To change these settings by remote control, the DIP switches “Colour of LED” must be

set to OFF.

10 2 3 4 5 6 7

Red Green Blue Yellow

RedO Green Blue YellowPinkTurquoise White

RedO

Example:

Green Blue YellowPinkTurquoise White

2No detection Detection

reen

or or or or

Animation

1 2 3 4 5 6 7 8

Brightness

1 2 3

Signal sound

Sound

1 2 3

DIP

123

= Factory setting

Signal sound To change these settings by remote control, the DIP switch “Signal sound” must be set

to OFF.

short sound

long sound

External control signal (e.g. function WC control)

Optical and acoustic feedback in the event of external activation:

Colour of LED

Colour according to

DIP switch “colour LED”

10 2 3 4 5 6 7

Red Green Blue Yellow

RedO Green Blue Yellow Pink TurquoiseWhite

or or or or

Animation

1 2 3 4 5 6 7 8

Signal sound

short sound

long sound

= Factory setting

DIP

Troubleshooting

Fault LED Possible causes Elimination

The door does not open. Faulty or no power supply. XCheck the power supply.

Range is too small. XAdjust range.

XRemove metallic objects in

front of the sensor.

Wired wrong.

XCheck wiring and relay connection.

The door remains open. The environment is inuencing the

functional ability of the sensor.

XRemove moving objects from

near the sensor.

Wired wrong.

XCheck wiring and relay connection.

The door remains open after de-

tection/activation.

Wrong output mode. XSwitch the output mode to

pulse mode.

Wired wrong.

XCheck wiring and relay connection.

LED is lit

LED is not lit

GEZE GmbH

Reinhold-Vöster-Straße 21–29

71229 Leonberg

Germany

Tel.: 0049 7152 203 0

Fax: 0049 7152 203 310

www.geze.com

BEA no.:

47.0508 V1 - 06.2021

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere GEZE Türöffnungssystem Handbücher

GEZE

GEZE TS1000 Bedienungsanleitung

GEZE

GEZE TS 5000 Gebrauchsanweisung

GEZE

GEZE Slimdrive EMD Leitfaden

GEZE

GEZE Slimdrive SL NT Kurzanleitung

GEZE

GEZE TS 5000 R Bedienungsanleitung

GEZE

GEZE Levolan 60 Bedienungsanleitung

GEZE

GEZE TSA 160 NT Betriebsanleitung

GEZE

GEZE TS 4000 R Bedienungsanleitung

GEZE

GEZE TS4000 Bedienungsanleitung

GEZE

GEZE Powerturn Kurzanleitung

GEZE

GEZE E-ISM Bedienungsanleitung

GEZE

GEZE TS 5000 Gebrauchsanweisung

GEZE

GEZE Perlan AUT-NT Bedienungsanleitung

GEZE

GEZE ECturn Kurzanleitung

GEZE

GEZE Slimdrive SL NT GGS Bedienungsanleitung

GEZE

GEZE TS 5000 ISM BG Bedienungsanleitung

GEZE

GEZE Powerturn Series Kurzanleitung

GEZE

GEZE TS 5000 R Bedienungsanleitung

GEZE

GEZE Slimdrive EMD Bedienungsanleitung

GEZE

GEZE GC 308 R Bedienungsanleitung

GEZE

GEZE ECturn Kurzanleitung

GEZE

GEZE FA GC 150 Kurzanleitung

GEZE

GEZE PERLAN 140 Bedienungsanleitung

GEZE

GEZE TS 5000 Gebrauchsanweisung

Beliebte Türöffnungssystem Handbücher anderer Marken

Pamex

Pamex KT-INP35 Bedienungsanleitung

Cal-Royal

Cal-Royal N-F77CVR Bedienungsanleitung

Scrigno

Scrigno OPEN1000 Bedienungsanleitung

TriMark

TriMark UM 34 Bedienungsanleitung

BFT

BFT WIND RMB 130B 200 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Besam

Besam Swingmaster MP Leitfaden

CRL

CRL SENIOR PRIMA Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 1431 Series Bedienungsanleitung

GAL

GAL MOVFR Technisches Datenblatt

Normstahl

Normstahl IDO7 Bedienungsanleitung

Häfele

Häfele Finetta T 70 VF Bedienungsanleitung

AGS

AGS D-PL Handbuch

Stanley

Stanley MA900ñ Montageanleitung

WITTUR

WITTUR Hydra Plus UD300 Handbuch

Alutech

Alutech TR-3019-230E-ICU Montage- und Bedienungsanleitung

MPC

MPC ATD ACTUATOR 50 ATD-313186 Operating and Technisches Datenblatt

Chamberlain

Chamberlain T Bedienungsanleitung