GFA ELEKTROMAT FT 60.4-45,00 Bedienungsanleitung
f
Pos: null /BA_Module/BA_ AA Deckblatt/BAAA000 001_M003 @ 17\mod_14442117 55814_28.docx @ 891110 @ @ 1
Installation Instructions
ELEKTROMAT
FT 60.4-45,00
Model: 10003292 00011
-en-
Status: 24.02.2020
Pos: null /BA_Module/BA_ Seitenumbruch @ 0\ mod_1190719383361_0.d ocx @ 550 @ @ 1
2
Pos: null /BA_Module/BA_ CA Leerblatt/BACA00 0001_M002 @ 15\mod_1416821 436083_28.doc x@ 864410 @ @ 1
GfA ELEKTROMATEN GmbH & Co. KG
Wiesenstraße 81
D-40549 Düsseldorf
www.gfa-elektromaten.de
Pos: null /BA_Module/BA_ Seitenumbruch @ 0\ mod_1190719383361_0.d ocx @ 550 @ @ 1
3
Pos: null /BA_Module/BA_ DA Inhaltsverzeic hnis/BADA000001_M001 @ 0\ mod_1192624580455_28. docx @ 710 @ @ 1
Table of contents
1General safety information .............................................................................................. 4
2Technical Data ................................................................................................................ 5
3Mechanical installation .................................................................................................... 6
4Electrical installation ....................................................................................................... 9
5Limit switch adjustment ................................................................................................. 10
6Motor connection .......................................................................................................... 12
7Alternative motor connection ......................................................................................... 12
8Limit switch connection ................................................................................................. 13
9Emergency manual operation lever ............................................................................... 14
10Completing commissioning / inspection ......................................................................... 15
11Declaration of incorporation / Declaration of conformity ................................................. 16
Pos: null /BA_Module/BA_ Seitenumbruch @ 0\ mod_1190719383361_0.d ocx @ 550 @ @ 1
Symbols
Warning - Potential injury or danger to life!
Warning - Danger to life from electric current!
Note - Important information!
▶ Requirement - Required action!
Schematic representations are based on product examples. Deviations from delivered
products are possible.
4
Pos: null /BA_Module/BA_ EA Sicherheitshinweise/BAEA 000005_M002 @ 4\mod_13 36032805351_28.doc x @ 745180 @ 1 @ 1
1General safety information
Specified normal use
The drive unit is intended for horizontally-driven folding doors.
The safe operation is only guaranteed with normal specified use. The drive unit is to be
protected from rain, moisture and aggressive ambient conditions. No liability for damage
caused by other applications or non-observance of the information in the manual.
Modifications are only permitted with the agreement of the manufacturer. Otherwise the
Manufacturer’s Declaration shall be rendered null and void.
Safety information
Installation and initial operation tasks are to be performed by trained, skilled fitters only.
Only trained electrical craftsmen are permitted to work on electrical equipment. They must
assess the tasks assigned to them, recognise potential danger zones and be able to take
appropriate safety measures.
The installation is only to be carried out with the supply off.
Observe the applicable regulations and standards.
Coverings and safety devices
Do not operate unless corresponding coverings and safety devices are fitted/installed.
Ensure that gaskets are correctly positioned and cable glands are correctly tightened.
Spare parts
Use only original spare parts.
Pos: null /BA_Module/BA_ Seitenumbruch @ 0\ mod_1190719383361_0.d ocx @ 550 @ @ 1
5
Pos: null /BA_Module/BA_ FA Technische Daten/BAF A001004_M001 @ 0\mod_119323 6602238_28.doc x@ 1248 @ 1 @ 1
2Technical Data
Type FT SG50/SG85
Output torque 600 Nm
Output speed 4 rpm
Output shaft / hollow shaft 45,00 mm
Maximum output speed open / close
for frequency inverter operation 7 / 7 rpm
Maximum holding torque 2900 Nm
Supply voltage 3N~ 400 V
Operating current 1,10 A
Operating frequency 50 Hz
Power factor cos φ 0,87
Maximum movement per hour 20 h-1
Class of protection IP 65
Limit switch range
(maximum revolutions of output shaft / hollow shaft) 1
Temperature range -10 / +40 (+60) °C
Pos: null /BA_Module/BA_ FC Temperaturbereic h/BAFC000001_M002 @ 23\mod_150 8937126225_28.doc x@ 105509 8 @ @ 1
1) When using a temperature range of +40°...+60°C use half of maximum movements per hour.
Pos: null /BA_Module/BA_ FD Daten Endschalter/ BAFD000002_M001 @ 11\mod_13 72072121894_28.doc x @ 804291 @ @ 1
Caution - Component damage can result!
The maximum current that can be switched over the limit switch is
1A for 230 V AC and 0.4 A for 24V DC
Pos: null /BA_Module/BA_ Seitenumbruch @ 0\ mod_1190719383361_0.d ocx @ 550 @ @ 1
6
Pos: null /BA_Module/BA_ GA Mechanische Montage/ BAGA006603_M001 @ 0\mod_12 73581431158_28.doc x @ 528695 @ 1 @ 1
3Mechanical installation
Prerequisites
The permissible loads on walls, fastenings, mountings and transmission elements must not
be exceeded, even for maximum holding torques or locking torques (▶ refer to technical
data).
Connection elements
▶ Self-locking connection
elements with a minimum
strength of 800 N/mm2
(8.8) must be used.
▶ Utilize the hole diameter
to the full.
▶ Use adequately
dimensioned washers for
elongated holes.
BAGAB00002_Z002 BAGAB 00003_Z002
3 : 1
Permissible mounting positions
BAGAC06401_Z001
7
Mounting
Four holes are provided for mounting.
8
Installation
The descriptions below apply to general door specifications. The specifications of the door
manufacturer must also be observed during installation.
Warning - Potential injury or danger to life!
During installation, be sure to use a lifting device that has a sufficient load-
carrying capacity.
▶ Tighten all connection elements (M12) to
75 Nm. Install all other connection
elements according to the specifications of
the door manufacturer.
BAGAE06401_Z001
75 Nm
8.8
8.8
8.8
8.8
8.8
8.8
8.8
▶ The drive unit has a friction clutch as
protection against overload. The friction
clutch is set to the output torque. Turning
to the left reduces the output torque.
BAGAE06402_Z001
Pos: null /BA_Module/BA_ Seitenumbruch @ 0\ mod_1190719383361_0.d ocx @ 550 @ @ 1
9
Pos: null /BA_Module/BA_ HA Elektrische Montage/ BAHA040101_M001 @ 0\mod_ 1222157034316_28. docx @ 83294 @ 1 @ 1
4Electrical installation
Warning - Danger to life from electric current!
Switch the mains OFF and check that the cables are de-energised
Observe the applicable regulations and standards
Make a proper electrical connection
Use suitable tools
Performing electrical installation
Remove the cover. Insert the motor plug. Insert the limit switch plug.
BAHAA04_Z001
BAHAC01_Z001
Completing the electrical installation
Mount the cable entries and/or cable glands.
Pos: null /BA_Module/BA_ Seitenumbruch @ 0\ mod_1190719383361_0.d ocx @ 550 @ @ 1
10
Pos: null /BA_Module/BA_I A Endschaltereins tellung/BAIA061131 _M001 @ 0\mod_126345881099 5_28.docx @ 477434 @ 1 @ 1
5Limit switch adjustment
Adjust the limit switches to define the final limits positions for OPEN and CLOSE.
Prerequisite
The door must open when the OPEN
pushbutton is operated. If the door closes, L1
and L2 must exchanged with the current
switched off.
Adjusting the OPEN limit position
Use the OPEN pushbutton to open the door
to the desired OPEN final limit position.
Rotate the cam of the OPEN limit switch S3
to the middle of tappet ①.
Tighten the screw of the cam ②.
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere GFA Gleichstromantrieb Handbücher
GFA
GFA ELEKTROMAT SI 13.100 FU-25,40 Bedienungsanleitung
GFA
GFA ELEKTROMAT SI 25.15-30,00 Bedienungsanleitung
GFA
GFA ELEKTROMAT SIK 17.10 WS-30,00 Bedienungsanleitung
GFA
GFA ELEKTROMAT SI 14.20-25,00 Bedienungsanleitung
GFA
GFA ELEKTROMAT SI 40.15-40,00 Ex Bedienungsanleitung
GFA
GFA ELEKTROMAT SI 45.15-40,00 GA45/15GD Bedienungsanleitung
GFA
GFA ELEKTROMAT SI 75.20 FU-55,00 Bedienungsanleitung
GFA
GFA ELEKTROMAT ST 80.24-50,00 Bedienungsanleitung
GFA
GFA ELEKTROMAT SI 25.35-30,00 Bedienungsanleitung
GFA
GFA ELEKTROMAT SI 55.40 FU-40,00 Bedienungsanleitung
GFA
GFA 10005484 00001 Bedienungsanleitung
GFA
GFA ELEKTROMAT SI 25.15-30,00 Bedienungsanleitung
GFA
GFA ELEKTROMAT ST 16.15-40,00 Bedienungsanleitung
GFA
GFA ELEKTROMAT ST 9.24-25.00 Bedienungsanleitung
GFA
GFA ELEKTROMAT SIK 25.10 WS-30,00 Bedienungsanleitung
GFA
GFA ELEKTROMAT SI 6.160 FU-25,00 GA06/160MGDU Bedienungsanleitung
GFA
GFA ELEKTROMAT SI 100.30 FU-55,00 10003917 10011 Bedienungsanleitung
GFA
GFA ELEKTROMAT SI 40.24-40,00 Bedienungsanleitung
GFA
GFA ELEKTROMAT SI 35.15-40,00 GA35/15GD Bedienungsanleitung
GFA
GFA 10003672 10011 Bedienungsanleitung
Beliebte Gleichstromantrieb Handbücher anderer Marken
Vincent Associates
Vincent Associates UNIBLITZ ED12DSS Bedienungsanleitung
EKSMA OPTICS
EKSMA OPTICS DQ-100-4 Stücklistenhandbuch
Chamberlain Garog
Chamberlain Garog D Series Bedienungsanleitung
Parker
Parker PDS Series Bedienungsanleitung
Festo
Festo DGC G Series Einrichtungshandbuch
Binks
Binks QS-5012-1-CE Bedienungsanleitung
