GFA ELEKTROMAT SI 35.100 FU-40,00 Bedienungsanleitung

Installation Instructions

ELEKTROMAT

SI 35.100 FU-40,00

Model: 10003833 10011

-en-

Status: 23.08.2018

GfA ELEKTROMATEN GmbH & Co. KG

Wiesenstraße 81

D-40549 Düsseldorf

www.gfa-elektromaten.de

[email protected]

Table of contents

1General safety information .............................................................................................. 4

2Technical Data ................................................................................................................ 5

3Mechanical installation .................................................................................................... 6

4Electrical installation ..................................................................................................... 10

5Limit switch adjustment ................................................................................................. 11

6Motor connection .......................................................................................................... 12

7Limit switch connection ................................................................................................. 12

8Emergency manual operation (emergency hand crank) ................................................ 13

9Completion of commissioning / testing .......................................................................... 15

10Declaration of incorporation / Declaration of conformity ................................................. 18



Symbols

Warning - Potential injury or danger to life!

Warning - Danger to life from electric current!

Note - Important information!

▶ Requirement - Required action!

Schematic representations are based on product examples. Deviations from delivered

products are possible.

1 General safety information

Specified normal use

The drive unit is intended for doors, which have to be secured against falling down; a safety

brake is included in the gearbox. The drive unit is directly mounted on the door shaft.

The safe operation is only guaranteed with normal specified use. The drive unit is to be

protected from rain, moisture and aggressive ambient conditions. No liability for damage

caused by other applications or non-observance of the information in the manual.

Modifications are only permitted with the agreement of the manufacturer. Otherwise the

Manufacturer’s Declaration shall be rendered null and void.

Safety information

Installation and initial operation tasks are to be performed by trained, skilled fitters only.

Only trained electrical craftsmen are permitted to work on electrical equipment. They must

assess the tasks assigned to them, recognise potential danger zones and be able to take

appropriate safety measures.

The installation is only to be carried out with the supply off.

Observe the applicable regulations and standards.

Coverings and safety devices

Do not operate unless corresponding coverings and safety devices are fitted/installed.

Ensure that gaskets are correctly positioned and cable glands are correctly tightened.

Spare parts

Use only original spare parts.

2 Technical Data

Type SG 85F

Output torque 350 (290) 1) Nm

Output speed OPEN 15-100 rpm

Output speed CLOSE 15-55 rpm

Output speed CLOSE > 2,5m 15-55 rpm

Output shaft / hollow shaft 40,00 mm

Locking torque moment 990 Nm

Safety brake (testhouse/approval number) 14-003612-PR03

Supply voltage 3~ 400 V

Maximum holding torque 350 Nm

Operating current 12,40 A

Operating frequency 50 Hz

Power factor cos φ 0,76

Maximum movement per hour 40 h-1

Hand forces 376 N

Class of protection IP 65

Limit switch range

(maximum revolutions of output shaft / hollow shaft) 20

Braking torque 9 / 9 Nm

Braking voltage 103 / 103 V DC

Rectifier type FU

Temperature range +5 / +40 (+60) 2) °C

Operating sound pressure level < 70 dB(A)

Abtriebsdrehmoment, das konstant über den gesamten Endschalterbereich und die maximalen Schaltungen pro Stunde genutzt werden kann.

2) When using a temperature range of +40°...+60°C use half of maximum movements per hour.

3 Mechanical installation

Prerequisites

The permissible loads on walls, fastenings, mountings and transmission elements must not

be exceeded, even for maximum holding torques or locking torques (▶ refer to technical

data).

Connection elements

▶ Self-locking connection

elements with a minimum

strength of 800 N/mm2

(8.8) must be used.

▶ Utilize the hole diameter

to the full.

▶ Use adequately

dimensioned washers for

elongated holes.

BA GAB00002_Z002 BAGAB00003_Z002

3 : 1

Permissible mounting positions

BAGAC0 30 0 1 _Z0 0 2

Mounting

Two elongated holes are provided for mounting.

BAGAD03 0 0 1 _Z0 0 3

Installation

The descriptions below apply to general door specifications. The specifications of the door

manufacturer must also be observed during installation.

Warning - Potential injury or danger to life!

 During installation, be sure to use a lifting device that has a sufficient load-carrying

capacity.

▶ Thoroughly grease the door shaft. BAGAE01001_Z003

▶ Mount the keys.

BAGAE03002_Z001

▶ Attach the drive unit. BAGAE03005_Z002

▶ Tighten all connection elements (M12) to

75 Nm. Install all other connection

elements according to the specifications of

the door manufacturer.

BAGAE03010_Z002

75 Nm

8.8

4 Electrical installation

Warning - Danger to life from electric current!

 Switch the mains OFF and check that the cables are de-energised

 Observe the applicable regulations and standards

 Make a proper electrical connection

 Use suitable tools

Performing electrical installation

Remove the cover. Insert the motor plug. Insert the limit switch plug.

BAHEA02_Z001 BAHEB01_Z001 BAHEC01_Z001

Completing the electrical installation

Mount the cable entries and/or cable glands.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere GFA Gleichstromantrieb Handbücher

GFA

GFA ELEKTROMAT SI 260.9-80,00 Bedienungsanleitung

GFA

GFA 10004146 10011 Bedienungsanleitung

GFA

GFA ELEKTROMAT SE 14.15-25,40 Bedienungsanleitung

GFA

GFA ELEKTROMAT SI 55.10-40,00 Bedienungsanleitung

GFA

GFA 10003672 10011 Bedienungsanleitung

GFA

GFA ELEKTROMAT SI 75.20 FU-55,00 Bedienungsanleitung

GFA

GFA KE 9.24-25,00 Ex Bedienungsanleitung

GFA

GFA SI 40.40 FU-40,00 Bedienungsanleitung

GFA

GFA ELEKTROMAT ST 16.24 Bedienungsanleitung

GFA

GFA ELEKTROMAT ST 16.15-40,00 Bedienungsanleitung

GFA

GFA ELEKTROMAT SI 40.15-40,00 Ex Bedienungsanleitung

GFA

GFA ELEKTROMAT SE 9.24 WS-25,40 Bedienungsanleitung

GFA

GFA ELEKTROMAT SI 60.24-55,00 Bedienungsanleitung

GFA

GFA ELEKTROMAT SI 75.15-55,00 Bedienungsanleitung

GFA

GFA ELEKTROMAT SI 25.15-30,00 GA25HC/15GD Bedienungsanleitung

GFA

GFA ELEKTROMAT SI 13.100 FU-25,40 Bedienungsanleitung

GFA

GFA ELEKTROMAT SI 6.160 FU-25,00 GA06/160MGDU Bedienungsanleitung

GFA

GFA ELEKTROMAT ST 9.24-25.00 Bedienungsanleitung

GFA

GFA ELEKTROMAT SI 85.10-55,00 GA85/10GD Bedienungsanleitung

GFA

GFA ELEKTROMAT SI Bedienungsanleitung

GFA

GFA ELEKTROMAT SI 50.80 FU-55,00 Bedienungsanleitung

GFA

GFA ELEKTROMAT SI 25.15-30,00 Ex Bedienungsanleitung

GFA

GFA ELEKTROMAT SI 180.12 FU-60,00 Bedienungsanleitung

GFA

GFA ELEKTROMAT FS 50.20-40,00 Bedienungsanleitung

Beliebte Gleichstromantrieb Handbücher anderer Marken

Chamberlain Garog

Chamberlain Garog D Series Bedienungsanleitung

Parker

Parker PDS Series Bedienungsanleitung

Festo

Festo DGC G Series Einrichtungshandbuch

Binks

Binks QS-5012-1-CE Bedienungsanleitung

Danfoss

Danfoss VLT 2800 Series Technisches Datenblatt

ABB

ABB ACQ580-01 Series Installationshandbuch

YASKAWA

YASKAWA CANopen SI-S3 Bedienungsanleitung

GE D20A6 Bedienungsanleitung

Unex

Unex MC-D-250-1000-050W-TW Bedienungsanleitung

Geckodrive

Geckodrive G213V Bedienungsanleitung

ABB

ABB RSYC-01 Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex 700S Betriebsanleitung

WEG

WEG DeviceNet CFW500 Bedienungsanleitung

Siemens

Siemens SINAMICS G Datenblatt

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Betriebsanleitung

SOMFY

SOMFY JR RU 30 Bedienungsanleitung

Beckhoff

Beckhoff AX8911 Bedienerhandbuch

Lenze

Lenze 8200 vector Bedienungsanleitung