GFA ELEKTROMAT ST 16.24 Bedienungsanleitung

Installation Instructions

ELEKTROMAT

ST 16.24-40,00

Model: 10002992 00024

-en-

Status: 22.11.2019

GfA ELEKTROMATEN GmbH & Co. KG

Wiesenstraße 81

D-40549 Düsseldorf

www.gfa-elektromaten.de

[email protected]

Table of contents

1General safety information .............................................................................................. 4

2Technical Data ................................................................................................................ 5

3Mechanical installation .................................................................................................... 6

4Electrical installation ..................................................................................................... 10

5Motor connection .......................................................................................................... 11

6Limit switch connection ................................................................................................. 11

7Completing commissioning / inspection ......................................................................... 12

8Declaration of incorporation / Declaration of conformity ................................................. 14



Symbols

Warning - Potential injury or danger to life!

Warning - Danger to life from electric current!

Note - Important information!

▶ Requirement - Required action!

Schematic representations are based on product examples. Deviations from delivered

products are possible.

1General safety information

Specified normal use

The drive unit is intended for horizontally operating sliding doors.

The safe operation is only guaranteed with specified normal use. The drive unit is to be

protected from rain, moisture and aggressive ambient conditions. No liability for damage

caused by other applications or non-observance of the information in the manual.

Modifications are only permitted with the agreement of the manufacturer. Otherwise the

Manufacturer’s Declaration shall be rendered null and void.

Safety information

Installation and initial operation tasks are to be performed by skilled personnel only.

Only trained electrical craftsmen are permitted to work on electrical equipment. They must

assess the tasks assigned to them, recognise potential danger zones and be able to take

appropriate safety measures.

Installation work is only to be carried out with the supply off.

Observe the applicable regulations and standards.

Coverings and protective devices

Do not operate unless corresponding coverings and protective devices are installed.

Ensure that gaskets are fitted correctly and that cable glands are correctly tightened.

Spare parts

Only use original spare parts.

2Technical Data

Type SG 85R

Output torque 160 Nm

Output speed 24 rpm

Output shaft / hollow shaft 40,00 mm

Maximum output speed open / close

for frequency inverter operation 42 / 42 rpm

Maximum door weight 16000 N

Supply voltage 3N~ 400 V

Operating current 1,80 A

Operating frequency 50 Hz

Power factor cos φ 0,51

Maximum movement per hour 20 h-1

Class of protection IP 54

Limit switch range

(maximum revolutions of output shaft / hollow shaft) 20

Braking torque of magnetic brake 130 Nm

Braking voltage 103 V DC

Rectifier type B1 230/103

Temperature range -10 / +40 (+60) °C

1) When using a temperature range of +40°...+60°C use half of maximum movements per hour.

Temperature Extension!

If the magnetic brake will be continuously supplied the drive can be fitted into areas

down to a -20°C ambient temperature.

3Mechanical installation

Prerequisites

The permissible loads on walls, fastenings, mountings and transmission elements must not

be exceeded, even for maximum holding torques or locking torques (▶ refer to technical

data).

Connection elements

▶ Self-locking connection

elements with a minimum

strength of 800 N/mm2

(8.8) must be used.

▶ Utilize the hole diameter

to the full.

▶ Use adequately

dimensioned washers for

elongated holes.

BA GAB00002_Z002 BAGAB00003_Z002

3 : 1

Permissible mounting positions

BAGAC03301_Z002

Mounting

Four holes are provided for mounting.

BAGAD03301_Z002

Installation

The descriptions below apply to general door specifications. The specifications of the door

manufacturer must also be observed during installation.

Warning - Potential injury or danger to life!

During installation, be sure to use a lifting device that has a sufficient load-

carrying capacity.

Ensure that there is sufficient space around the handwheel for safe operation of

the friction clutch.

▶ The output-shaft must not be shortened.

BAGAE03301_Z001

▶ Tighten all connection elements (M12) to

75 Nm. Install all other connection

elements according to the specifications of

the door manufacturer.

BAGAE003302_Z002

75 Nm

Warning - Potential injury or danger to life!

Disconnect the electric supply to set the friction clutch.

The friction clutch provides overload

protection. It is tightened finger-tight at the

factory. Turning to the right (handwheel or

screw) increases the transferable torque.

Turning to the left decouples the drive unit

from the door (does not apply to version with

floor release).

BAGAE3303_Z002

4Electrical installation

Warning - Danger to life from electric current!

Switch the mains OFF and check that the cables are de-energised

Observe the applicable regulations and standards

Make the electrical connection according to standard

Use suitable tools

Performing electrical installation

Remove the cover. Connect the motor cables

and brake cables.

BAH AA17_Z001

BAH AB0 8 _ Z0 01

Completing the electrical installation

Mount the cable entries and/or cable glands.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere GFA Gleichstromantrieb Handbücher

GFA

GFA ELEKTROMAT SI 65.15-40,00 Bedienungsanleitung

GFA

GFA ELEKTROMAT SI 40.24-40,00 Bedienungsanleitung

GFA

GFA ELEKTROMAT SI 17.15-30,00 Bedienungsanleitung

GFA

GFA ELEKTROMAT SIK 25.10 WS-30,00 Bedienungsanleitung

GFA

GFA ELEKTROMAT SI 25.15-30,00 Ex Bedienungsanleitung

GFA

GFA ELEKTROMAT SI 75.15-55,00 Bedienungsanleitung

GFA

GFA ELEKTROMAT SI 35.100 FU-40,00 Bedienungsanleitung

GFA

GFA ELEKTROMAT SG 85 Bedienungsanleitung

GFA

GFA ELEKTROMAT SI 55.20 FU-40,00 Bedienungsanleitung

GFA

GFA ELEKTROMAT SE 9.24 WS-25,40 Bedienungsanleitung

GFA

GFA ELEKTROMAT ST 80.24-50,00 Bedienungsanleitung

GFA

GFA ELEKTROMAT ST 16.15-40,00 Bedienungsanleitung

GFA

GFA ELEKTROMAT ST 30.24-40,00 Bedienungsanleitung

GFA

GFA ELEKTROMAT SI 35.30-40,00 Bedienungsanleitung

GFA

GFA ELEKTROMAT SI 14.15-25,00 Bedienungsanleitung

GFA

GFA ELEKTROMAT SI 55.40 FU-40,00 Bedienungsanleitung

GFA

GFA 10004146 10011 Bedienungsanleitung

GFA

GFA ELEKTROMAT SG 186F Bedienungsanleitung

GFA

GFA ELEKTROMAT SI 45.7 WS-40,00 Bedienungsanleitung

GFA

GFA ELEKTROMAT SI 25.15-30,00 Ex Bedienungsanleitung

GFA

GFA 10003166 10011 Bedienungsanleitung

GFA

GFA ST 60.15-50,00 Bedienungsanleitung

GFA

GFA KE 9.24-25,00 Ex Bedienungsanleitung

GFA

GFA ELEKTROMAT SI 75.24-55,00 Bedienungsanleitung

Beliebte Gleichstromantrieb Handbücher anderer Marken

Vincent Associates

Vincent Associates UNIBLITZ ED12DSS Bedienungsanleitung

EKSMA OPTICS

EKSMA OPTICS DQ-100-4 Stücklistenhandbuch

Chamberlain Garog

Chamberlain Garog D Series Bedienungsanleitung

Parker

Parker PDS Series Bedienungsanleitung

Festo

Festo DGC G Series Einrichtungshandbuch

Binks

Binks QS-5012-1-CE Bedienungsanleitung

Danfoss

Danfoss VLT 2800 Series Technisches Datenblatt

ABB

ABB ACQ580-01 Series Installationshandbuch

YASKAWA

YASKAWA CANopen SI-S3 Bedienungsanleitung

GE D20A6 Bedienungsanleitung

Unex

Unex MC-D-250-1000-050W-TW Bedienungsanleitung

Geckodrive

Geckodrive G213V Bedienungsanleitung

ABB

ABB RSYC-01 Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex 700S Betriebsanleitung

WEG

WEG DeviceNet CFW500 Bedienungsanleitung

Siemens

Siemens SINAMICS G Datenblatt

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Betriebsanleitung

SOMFY

SOMFY JR RU 30 Bedienungsanleitung