Giant BP100 Bedienungsanleitung
Contents:
Installation Instructions: page 2
Pump Specications: page 3
Parts List: page 4
Exploded View / Kits: page 5
Recommended Spare Parts List: page 6
Pump Mounting Selection Guide: page 6
Torque Requirements: page 6
Repair Instructions: pages 7-10
Dimensions: page 11
Warranty Information: back page
Triplex Ceramic
Plunger Pump
Operating Instructions/
Repair and Service
Manual
Model
BP100
Bentonite Pump
Updated 04/22
2
Operation and Maintenance
Check oil level prior to starting and en-
sure trouble-free water supply . Oil: Use
only 23.7 ounces (0.7 litres) of Giant oil
(p/n 01154) ISO VG 220 (e.g. Aral Degol
BG220) or SAE 90 gear oil.
Initial change after 50 operating hours and
then every 1000 operating hours or after 1
year if used less.
Caution! When operating in damp places
or with high temperature uctuations.
Should condensate (frothy oil) occur in the
gear box, oil must be changed immediately.
Maximum input pressure 145 PSI (10
bar).
Maximum suction head -4.35 PSI (-0.3
bar) (dependent on the viscosity of the
medium). Maximum input pressure 145
PSI (10 bar), maximum suction head -4.35
PSI (-0.3 bar). Make sure that suction
pulsation is suciently dampened - water
column resonance must be avoided.
Safety Rules
Pump operation without safety valve as
well as any excess in temperature or speed
limits automatically voids the warranty . The
safety valve must be regulated in accor-
dance with the guidelines for liquid spraying
units so that the admissible operating pres-
sure can not be exceeded by more than
10%.
When the pump is in operation, the open
shaft end must be oovered up by a shaft
protector (17). The driven shaft side and
coupling (or belt guard) should have a
metal guard over all moving parts.
Before any maintenance to the pump takes
place, the pressure in discharge line and in
pump must be at zero. Close suction line.
Disconnect fuses to ensure that the driving
motor is not accidentally switched on.
Before starting the pump, make sure that
all parts on the pressure side of the unit are
vented and relled (with pressure at zero).
In order to prevent air, or an air/water-mix-
ture being absorbed and to prevent cavita-
tion occurring, the pump-NPSHR, positive
suction head and medium temperature
must be kept under control.
Cavitation and/or compression of gases
lead to uncontrollable pressure-kicks
which can ruin pump and unit parts and
also be dangerous to the operator or
anyone standing nearby.
The BP100 pump is suitable for pumping
clean water as well as for water containing
bentonite in a concentration of maximum 55
lbs. (25 kg) of bentonite diluted in 264 gal-
lons (1 cubic meter) of water.
INSTALLATION INSTRUCTIONS
3
Specications
Model BP100
Consult the factory for special requirements that must be met if the
pump is to operate beyond one or more of the limits specied above.
PULLEY INFORMATION
Pulley selection and pump speed are based on
a 1725 RPM motor and “B” section belts. When
selecting desired GPM, allow for a ±5% tolerance
on pumps output due to variations in pulleys, belts
and motors among manufacturers.
1. Select GPM required, then select appropriate
motor and pump pulley from the same line.
2. The desired pressure is achieved by selecting
the correct nozzle size that corresponds with the
pump GPM.
HORSEPOWER INFORMATION
Horsepower ratings shown are the power re-
quirements for the pump. Gas engine power
outputs must be approximately twice the pump
power requirements shown above.
We recommend that a 1.15 service factor be
specied when selecting an electric motor as the
power source. To compute specic pump horse-
power requirements, use the following formula:
(GPM X PSI) / 1450 = HP
U.S. (Metric)
Volume..................................................... 5.9 GPM................. (22.5 LPM)
Discharge Pressure ................................. 1885 PSI ................ (130 bar)
Maximum Crankshaft Speed ................................................... 750 RPM
Power Required....................................... 8.0 HP.................... (6.0 kW)
Plunger Diameter..................................... 1.02”....................... (26mm)
Stroke ...................................................... 0.79”....................... (20mm)
Crankcase Oil Capacity ........................... 24 .oz. .................. (0.7 L)
Temperature of Pumped Fluids................ 194 oF.................... (90o C)
Inlet Ports................................................................................. (2) 3/4” NPT
Discharge Ports ....................................................................... (2) 1/2” NPT
Crankshaft Mounting................................................................ Either Side
Shaft Rotation.......................................... Top of Pulley Towards Fluid End
Weight...................................................... 41.9 lbs. ................ (19 kg)
SPECIAL NOTE:
The theoretical gallons per revolution (gal/rev) is 0.0078667
To nd specic outputs at various RPM, use the formula:
GPM = 0.00787 x RPM
BP100 Horsepower Requirements
RPM GPM 500 PSI 1000 PSI 1500 PSI 1885 PSI
250 2.0 0.7 1.4 2.0 2.6
350 2.8 0.9 1.9 2.8 3.6
450 3.5 1.2 2.4 3.7 4.6
550 4.3 1.5 3.0 4.5 5.6
650 5.1 1.8 3.5 5.3 6.6
750 5.9 2.0 4.1 6.1 7.7
4
ITEM PART DESCRIPTIONS QTY
1 07294 Crankcase 1
2 06968 Oil Filler Cap with Gasket 1
3 07297 Cover, Crankcase 3
4 07298 O-Ring, Crankcase Cover 1
5 07299 Oil Dipstick 1
6 01009 O-Ring, Dip Stick 1
7 07186 Oil Sight Glass Assembly 1
9 01010 Screw, Crankcase Cover 4
10 01011-0400 Spring Washer, Cover Screw 4
11 07109 Oil Drain Plug 2
11A 06015 O-Ring 2
12 07302 Bearing Cover 2
13 07303 O-Ring, Bearing Cover 2
14 07459 Seal, Crankshaft 2
15 08388 Roller Bearing 2
15A 06962 Shim, 1.5mm 1-2
16 07114 Screw & Washer, Bearing Cover 6
17 05312 Shaft Protector 1
18 07309 Crankshaft 1
19 13331 Fitting Key 1
20 07310 Connecting Rod Assy. 3
20A 07311 Inner Hexagon Screw 3
20B 07122 Spring Washer 3
22 07315 Crosshead with Plunger Base 3
23 07314 Crosshead Pin 3
24 07360 Bolt Assembly
(Items 24B, 24C, 24D, 24E) 3
24A 07346 Ceramic Plunger 3
ITEM PART DESCRIPTIONS QTY
24B 08399 Tension Screw 3
24C 07023 O-Ring, Bolt Assy. (Viton) 3
24D 07203 Support Ring 3
24E 07258 Copper Seal Washer 3
25 05289 Flinger 3
26 07318 Radial Shaft Seal 3
28 07319 Shim, Stud 2
29 07320 Manifold 1
29A 11502 Inner Hexagon Stud Bolt 2
30 07335 Pressure Ring 3
31 11503 V-Sleeve 6
32 07349 Support Ring 3
33 07338 Pressure Spring 3
34 07325 Spring Retainer, Discharge 3
34A 07326-0100 Spring Retainer, Inlet 3
35 07312-0100 Valve Spring 6
36 07327 Valve Plate 6
37 06014 Valve Seat 6
38 06015 O-Ring, Valve Seat 6
39 07328 Valve Retainer, Inlet 3
39A 07329 Spacer 3
40 12057 O-Ring, Inlet Valve Retainer 3
41 07331 Plug, Inlet 3
42 07332 O-Ring, Inlet Plug 3
43 07213 Plug, Discharge 3
44 07214 O-Ring, Discharge Plug 3
45 07333 Stud Bolt 4
46 07158 Hex Nut, Stud Bolt 4
47 07159 Spring Washer, Stud Bolt 4
BP100 PARTS LIST
5
BP100 EXPLODED VIEW
Plunger Packing Repair - #09649
Item Part # Description Qty.
31 11503 V-Sleeve 6
40 12057 O-Ring, Inlet Valve Retainer 3
42 07332 O-Ring, Inlet Plug 3
Oil Seal Repair Kit - #09797
Item Part # Description Qty.
26 07318 Radial Shaft Seal 3
Valve Kit #09069
Item Part # Description Qty.
34 07325 Discharge Spring Retainer 3
34A 07326-0100 Inlet Spring Retainer 3
35 07312-0100 Valve Spring 6
36 07327 Valve Plate 6
37 06014 Valve Seat 6
38 06015 O-Ring, Valve Seat 6
40 12057 O-Ring, Inlet Valve Retainer 3
42 07332 O-Ring, Inlet Plug 3
44 07214 O-Ring, Discharge Plug 3
BP100 REPAIR KITS
May not be
present
6
Preventative Maintenance Check-List & Recommended Spare Parts List
Check Daily Weekly 50hrs Every Every Every
500hrs 1500hrs 3000hrs
500 hrs 1500 hrs 3000 hrs
Oil Level/Quality X
Oil Leaks X
Water Leaks X
Belts, Pulley X
Plumbing X
Recommended Spare Parts
Oil Change p/n 1154 X X
Plunger Packing Kits (1 kit/pump) X
(See page 5 for kit list)
Valve Assembly Kit (1 kit/pump) X
(See page 5 for kit list)
Oil Seal Kit (1 kit/pump) X
(See page 5 for kit list)
Pump Mounting Selection Guide
Bushings
07175 - 28 mm Tapered H Bushing
Pulley & Sheaves
01055 - 9.75” Cast Iron 2 gr. - AB Section
01062 - 7.75” Cast Iron - 2 gr. - AB Section
Rails
07358 - Plated Steel Channel Rails
(L=9.18” x W=1.88” x H=3.00”)
BP100 TORQUE SPECIFICATIONS
Position Part # Description Lubrication Info Torque Amount
7 07186 Oil Sight Glass Assembly Loctite 5910 106 in.-lbs. (12 Nm)
901010 Screw, Crankcase Cover 221 in.-lbs. (25 Nm)
11 07109 Oil Drain Plug 132 in.-lbs. (15 Nm)
16 07114 Screw Bearing Cover
20A 07311 Inner Hexagon Screw 22 ft.-lbs. (30 Nm)
24B 08399 Tension Screw Loctite 243 247 in.-lbs. (28 Nm)
26 07318 Radial Shaft Seal Loctite 403
41 07331 Plug, Inlet 51 ft.-lbs. (70 Nm)
43 07213 Plug, Discharge Loctite 243 51 ft.-lbs. (70 Nm)
45 07333 Stud Bolt Loctite 270
46 07158 Nut, Stud Bolt 200 in.-lbs. (22.5 Nm)
7
NOTE: Contact Giant Industries for Service School Information. Phone: (419)-531-4600
REPAIR INSTRUCTIONS - BP100 PUMP
1. With a 22mm socket, remove
the three discharge (43)
and three inlet (41) manifold
plugs.
2. Check o-ring (44) for wear and replace as necessary. Remove the
discharge spring retainer (34), valve spring (35), and valve plate
(36).
3. Use a small slide hammer
to remove valve seats (37)
from manifold (29). Inspect
valve plate (36) and valve
seats (37) for wear. If exces-
sive pitting is seen, replace
the worn parts. Check valve
seat o-ring (38) for wear and
replace as necessary.
4. Drain the oil from the pump.
Turn the pump over to remove
the four manifold stud nuts
(46) with a 19mm wrench.
5. Tap the back of the valve
41A 44 34 35 36
6. Remove the inlet valve re-
tainer assembly (34A-39)
7. Remove the o-ring, (40), valve plate (36), valve spring (35), spring
retainer (34A). Check valve retainer o-ring (40) for wear.
7A. Reassemble valve assemblies and install into manifold (29). Tighten
plugs to 52 ft.-lbs. (70 Nm).
casing (29) with a rubber mal-
let.
40 36 35 34A
8
NOTE: Contact Giant Industries for Service School Information. Phone: (419)-531-4600
REPAIR INSTRUCTIONS - BP100 PUMP
8. With a valve puller remove
the valve seat (37) and o-
ring (38).If excessive pitting
is seen, replace the worn
parts. Check valve seat o-ring
(38) for wear and replace as
necessary.
9. Remove the spacer (39A), pressure spring (33), support ring (32),
v-sleeves (31), and pressure ring (30), from the manifold (29) and
check for wear.
10.Inspect ceramic plunger
(24A) tips for wear. If nec-
essary, replacement of the
ceramic plungers may be
accomplished by removing
the plunger bolt assemblies
(24) with a 13mm wrench.
Ceramic plungers should now
slide o the stainless steel
plunger base (22). Excessive
resistance to plunger removal
may be overcome by heating
the stainless steel plunger
base. This will melt any
excess loc-tite beneath the
ceramic plunger allowing easy
removal.
24E
11.Replace copper ring (24E)
onto plunger bolt (24B).
Slide plunger bolt assembly
(24) into ceramic plunger
(24A). Apply a light lm
of loc-tite to plunger bolt
threads and place plunger
assembly onto stainless
steel plunger base (22) and
tighten to 310 in.-lbs. (35
Nm).
12.To replace plunger oil seals
(26), proceed to “Gear End
Disassembly” section below.
Otherwise, continue as de-
scribed below.
13.Before replacing pump manifold (29), rst rotate crankshaft
(18) until two outside plungers (24A) extend evenly forward.
Lubricate ceramic plungers with a light lm of oil. Carefully
and evenly slide manifold over plungers and press manifold
rmly against crankcase (1). Replace manifold stud bolts
(45), washers (47) and nut (46) and tighten to 59 ft.-lbs. (80
Nm).
30 31 31 32 33 39A
9
Gear End Disassembly
14. Remove the crankcase cover screws (9). Inspect the crankcase cover o-ring (4) for wear. Replace if neces-
sary.
15. Inspect the dipstick (5) vent hole for signs of clogging. Clean if necessary.
16. To remove the crankshaft (18), rst remove the bearing cover plates (12). Remove the key (19).
17. With a 5 mm allen wrench remove the connecting rod screws (20A) and rear portion of connecting rod as-
semblies (20). Push the connecting rod (20) and plunger rod (22) down as far as possible into the crankcase
housing.
18. Hold the pump rear assembly with a wooden xture, or other suitable device, in order to secure it while re-
moving the crankshaft (18). Using a plastic mallet, tap the crankshaft from one side while turning it from the
other side. The turning insures that during this sequence the crankshaft does not become wedged against
the front portion of the connecting rods (20). The far side bearing (15) will remain in the crankcase (1). When
free, the crankshaft can be removed by hand. The opposite side crankshaft seal (14) will be removed by this
procedure. It is important that you turn the crankshaft (18) constantly while tapping from the opposite
end to avoid any binding. The crankshaft bearing (15) remains on the crankshaft as it is removed. If
necessary, use a bearing puller to remove the crankshaft bearing (15).
19. Remove the front portion of the connecting rods (20) and plunger base assembly (22) from the rear of the
pump by pulling straight out of the crankcase crosshead guides. Notice that the connecting rod (20) halves
are numbered or colored. Connecting rods must be positioned with their numbers or colors on the
upper left-hand side, in the same numerical sequence as when they were removed.
20. Using a dowel and a rubber mallet, tap the oil seals (26) out from the rear of crankcase (1). The area onto
which the oil seal rests should be clean and dry. Put a small drop of loc-tite on the oil seals and place into
crankcase with lips facing the rear of the pump.
21. To remove the crosshead pin (23) from the crosshead (22), the assembly should be positioned on a wooden
xture to avoid damage to crosshead. Drive out the pin on opposite side of mark located on the crosshead.
On those pumps without mark on crosshead, drive out pin by tapping on tapered side of pin.
22. To remove the bearing (15) remaining in the crankcase (1), insert small end of Giant bearing tool and tap with
a rubber mallet until bearing and seal (14) are completely removed. The bearing can only be removed from
the inside by inserting the Giant Bearing Tool through the opposite side of the crankcase. The cross-
head guide in the crankcase should be inspected for possible damage.
REPAIR INSTRUCTIONS - BP100 PUMP
10
23. To reassemble, place the far bearing (15) in the crankcase (1) bearing housing and with the Giant Bearing
tool as a driver, tap into the crankcase using a rubber mallet.
24. Insert the far side crankshaft oil seal (14) with the Giant Bearing Tool making sure it is rmly seated and well
oiled. Always make sure that the crankshaft seal lip does not show signs of wear and that the garter spring
is rmly in place on the seal before reinserting into the pump. Replace the bearing cover (12) and o-ring (13)
and tighten securely.
25. Replace the front portion of the connecting rod (20) and plunger rod/ crosshead assembly (22) by press-tting
the crosshead pin (23). Make sure to insert the beveled edge of the crosshead pin into crosshead. If the
crosshead has a mark, install pin from marked side. The crosshead pin (23) should not extend beyond
either side of the crosshead (22) in order to prevent damage to the crosshead bore of the crankcase
(1).
26. Place each crosshead/ plunger assembly into the pump making sure that all of the parts are well oiled before
insertion into the crankcase (1). Notice that the connecting rod (20) halves are numbered or colored.
Connecting rods must be positioned with their numbers or colors on the upper left-hand side, in the
same numerical sequence as when they were removed.
27. Replace near side bearing (15) on crankshaft by using the Giant Bearing Tool and mallet to tap into place.
Take the crankshaft (18) end with the bearing (15) and insert the other end through the bearing housing and
tap with a rubber mallet until the bearing is seated.
28. When reassembling the connecting rods (20), note that the connecting rod halves are numbered or colored
and that the numbers or colors must be matched and aligned. Torque the connecting rod bolts to 310 in.-lbs.
29. Insert the near side crankshaft oil seal (14) with the Giant Bearing Tool making sure it is rmly seated and well
oiled. Replace the bearing cover (12) and o-ring (13) and tighten securely.
Seeinstructionsaboveforre-installinguidendontothegearend.
30. Fill the BP100 crankcase (1) with 23.7 oz. (0.7 liters) of Giant Industries’ oil and check the oil level with the
dipstick (5). Proper level is center of two lines. Reinstall the pump into your system.
REASSEMBLY INSTRUCTIONS - BP100 PUMP
Andere Giant Wasserpumpe Handbücher
Giant
Giant GP5128 Bedienungsanleitung
Giant
Giant LP460 Bedienungsanleitung
Giant
Giant P55W Bedienungsanleitung
Giant
Giant HR2527A Bedienungsanleitung
Giant
Giant GP5132HS Bedienungsanleitung
Giant
Giant P205 Repair and Bedienungsanleitung
Giant
Giant MP Series Bedienungsanleitung
Giant
Giant GP5136-5100 Bedienungsanleitung
Giant
Giant Triplex Ceramic Plunger Pump LP350 Fehlerbehebungshandbuch
Giant
Giant P46W-HK Bedienungsanleitung
Giant
Giant LP250-5100HK Bedienungsanleitung
Giant
Giant LP650 Bedienungsanleitung
Giant
Giant LP250 Bedienungsanleitung
Giant
Giant GP8055-Brine Bedienungsanleitung
Giant
Giant LP121A-5100 Bedienungsanleitung
Giant
Giant P300 Series Bedienungsanleitung
Giant
Giant MP4130-3100 Bedienungsanleitung
Giant
Giant GP7645GB Bedienungsanleitung
Giant
Giant GP7145 Bedienungsanleitung
Giant
Giant P200A-3100 Series Repair and Bedienungsanleitung
Beliebte Wasserpumpe Handbücher anderer Marken
Sykes AmeriPumps
Sykes AmeriPumps GP100M Fehlerbehebungshandbuch
DUROMAX
DUROMAX XP WX Series Bedienungsanleitung
BRINKMANN PUMPS
BRINKMANN PUMPS SBF550 Bedienungsanleitung
Franklin Electric
Franklin Electric IPS Bedienungsanleitung
Xylem
Xylem e-1532 Series Bedienungsanleitung
Milton Roy
Milton Roy PRIMEROYAL Bedienungsanleitung