Gio Electric Golf Bedienungsanleitung
PLEASE INSPECT YOUR GIO ELECTRIC TRON MOBILITY SCOOTER
UPON ARRIVAL AND REPORT ANY DAMAGES THAT MAY HAVE
OCCURRED DURING SHIPPING
⚠SAFETY INFORMATION ⚠
Thank you for purchasing the GIO Electric Golf Mobility Scooter. Please
note the following information to ensure your safety and get better use out of
your GIO Golf. Keep this manual safe for future reference.
Please read the manual prior to first use and do not permit anyone who has
not, operate the vehicle.
⚠NOT FOLLOWING THE SAFETY AND OPERATIONAL
INSTRUCTIONS IN THIS MANUAL MAY LEAD TO DAMAGE TO THE
SCOOTER AND INJURY TO THE RIDER ⚠
This scooter is primarily designed only for one adult, but does have the
additional rear bench. Never exceed the max load capacity of the vehicle.
500lbs (227kg)
Take extra care when handling the batteries inside your scooter. Avoid
directly touching contacts with damp hands or metal tools to prevent
electrocution.
To ensure the safety and reliability of your scooter, do not modify your
scooter, and always use parts, i.e. charger, specifically designed for the GIO
Tron.
Details contained in this manual are subject to change. Images are for
reference and may not reflect the final product.
01
⚠THIS SCOOTER IS ELECTRIC, TAKE PROPER CARE NOT TO
MAKE CONTACT WITH ELECTRICAL CONTACT WITH BODY OR
TOOLS. ⚠
⚠ALWAYS APPLY BRAKES WHILE GOING DOWNHILL TO CONTROL
SPEED AND AVOID SHARP TURNS AT HIGHER SPEEDS TO
PREVENT TIPPING SIDEWAYS! ⚠
⚠THIS VEHICLE WAS NOT MANUFACTURED FOR USE ON THE PUBLIC
ROADS AND THUS IS NOT A MOTOR VEHICLE SUBJECT TO THE
FEDERAL MOTOR VEHICLE SAFETY, BUMPER AND THEFT PREVENTION
STANDARDS OR THE EQUIPMENT ITEM IS NOT A SYSTEM, PART, OR
COMPONENT OF A MOTOR VEHICLE AND THUS IS NOT AN ITEM OF
MOTOR VEHICLE EQUIPMENT SUBJECT TO THE FEDERAL MOTOR
VEHICLE SAFETY STANDARDS. [591.5(A)] ⚠
Table of Contents
Riding Safety 3
Overview 4
Scooter Assembly 5
Operating & Adjusting Your Scooter 11
Maintenance & Care 18
Specifications & Troubleshooting 19
Warranty Information 22
02
Riding Safety
ALWAYS ride in accordance with local regulations for mobility scooters as
most places they are intended for sidewalk use and are not street legal
ALWAYS practice riding your scooter in an open area prior to driving
amongst vehicle/pedestrian traffic
ALWAYS accelerate slowly and steer with both hands
ALWAYS drive with caution at appropriate speeds
ALWAYS use your scooters turn signals and horn
ALWAYS obey local traffic law
ALWAYS be aware of your surroundings, pedestrians, traffic, etc
ALWAYS take extra care when driving in spaces shared with motor
vehicles: parking lots, driveways, crosswalks etc
ALWAYS check backup camera before reversing
ALWAYS apply brakes while driving downhill to regulate speed
ALWAYS take extra care driving in wet conditions
ALWAYS use your lights when driving in darker conditions
ALWAYS ensure the scooter is turned off and parking brakes are set prior to
getting in or out of the vehicle
ALWAYS adjust the seat while stationary
ALWAYS follow the battery/scooter care instructions
ALWAYS inspect your scooter prior to use
AVOID driving off-road or on surfaces that may lead to scooter damage
AVOID driving in conditions that may get the electric components wet
AVOID driving in conditions where you are not visible
AVOID overloading the scooter
AVOID inclines greater that the recommended maximum of 17°
AVOID going backward down sloped or uneven terrain
03
Riding Safety… continued
NEVER operate without reading this manual first
NEVER driving while fatigued or tired
NEVER driving if physically or mentally unable to
NEVER driving under the influence of drugs or alcohol
NEVER allow anyone under the age of 12yo to operate the scooter
NEVER drive distracted by using a cell phone while driving
NEVER turn the scooter off while in motion
NEVER use replacement parts not approved by GIO Electric
NEVER use a charger not included or approved of by GIO Electric
NEVER use an extension cord while charging
NEVER touch the motor after use, it is hot
NEVER ride the scooter while it is being transported via trailer, car lift etc
Overview
Thank you for your purchase of the GIO Electric Tron Mobility Scooter. It is
an easy to operate mobility scooter designed for outdoor use. This stylish
recreational mobility scooter doesn’t require any licensing, registration or
insurance.* (*unless required locally)
Get out of the elements and ride in style. The Golf is packed with features;
media center with integrated backup camera, generous top speed, long
driving range, rear shock suspension, heater, fan and opening windows and
more! This manual contains a wide range of general information and should
be read before you operate it.
04
Assembly
Your Golf arrives 90% assembled and requires the following to complete it.
We strongly recommend 2 people for assembly, as certain components are
large and will be more easily attached with support from a second person.
Step 1 - Unboxing
Unpack your Golf, remove the box by cutting along edges and peeling back
the cardboard. Carefully begin with the top most pieces, unfasten the bolts
in the shipping frame and remove pieces. All of the components should be
safely stored within the vehicle for travel.
Components include:
-Bumpers (front/rear), bumper hardware (x8 bolt - largest)
-Mirrors (left/right)
-Clear drip edging (left/right - self adhesive)
-Rear bench,bench support (black), hardware (x2 bolts - medium + x4
screws)
-Batteries (x5), brackets (green t-shaped x2), battery wires (x4), bracket
hardware (x4
bolts - medium), terminal bolts (x10 w/ spring washer & regular washer)
-Keys & fob (x2)
-Charger
Step 2 - Mirrors
Your mirrors are individually packed to protect them during shipping. Locate
the correct side mirror, remove the hex head bolts pre-installed into the
mounting on the door front, align the mirror with mounting holes and secure
into place with the removed bolts. Repeat on the other side.
05
Step 3 - Bumpers
Bumpers attach to mounting plates located on either side of the body at the
front and rear. Front mounts are visible just in front of the front wheels
through the wheel well, rear mounts are either visible below the body or
from above through the access provided before the bench is installed
With assistance align the bumper below the mounting plates and line up the
holes on the bumper with the holes on the mounting plate. Bolt upward into
the nut welded into the mounting plate, 2 bolts per side, 4 per bumper.
06
Step 4 - Battery Installation
Begin battery installation by opening the flap on the rear body that conceals
the charging port and breaker. Ensure the breaker is in the off position
before beginning installation. Locate the battery wires, and terminal
hardware.
Arrange the 5 batteries in the metal battery tray to allow for easy
connections below. Batteries will be connected in series, (Battery 1
connects to battery 2, 2 to 3, 3 to 4, 4 to 5) in the manner described next.
The connection process of an individual battery wire to each battery wire is
quite simple, repeat this basic process with each connection in the manner
and order described ahead.
07
Push back the plastic terminal cap to reveal the eyelet connector on the end
of the wire. Align the eyelet with the hole in the terminal you are currently
working on. Screw in one of the terminal bolts (each includes one washer
and 1 spring washer) and secure. Push the cap back into place.
Beginning with battery #1, connect a battery wire to the blue negative (-)
terminal. Color coordinate the terminal cap with the color of the terminal
itself to ensure the right connections are made. (Blue and Black both
representing negative (-) ) Next connect the other end of the battery wire to
the red positive (+) terminal on battery #2. Repeat the process in order so
the following connections are made: Battery 1 (-) → Battery 2 (+), Battery 2
(-) → Battery 3 (+), Battery 3 (-) → Battery 4 (+), Battery 4 (-) → Battery 5 (+)
Once the 5 batteries are connected in series you can locate the red (+) and
the black (-) battery leads coming from up from below the seat back which
are connected to your controller and charging port located in the
compartment behind the access panel in the seat back.
Connect the (-) lead to the (-) terminal on battery #5 and the (+) lead to the
(+) terminal on battery #1 in the same manner as the previous connections.
The batteries are now connected, flip the breaker to the on position and
power up the scooter to test to see if they are properly connected. Provided
proper function, power off the scooter and flip the breaker back to off and
finish the rest of the assembly process.
08
Once your batteries are correctly connected, you can secure them into
place with the green t shaped battery brackets. Secure with medium bolts
into the battery bracket mounts, below the large tube bench supports, see
images below. Depending on the layout of wires and batteries, the brackets
may be a better fit flipped with the shorter arms on the opposite side.
Step 5 - Rear Bench
With the batteries fully installed and bracketed into place, attach the black
bench support, bolting it into the mounting plates on the tubular bench
supports on either side of the bench area. Once complete, angle the rear
edge of the seat underneath the seat back and push the plastic bench into
place. Secure the front of the seat with screws by aligning the pre made
holes of the bench with the interior body piece behind it.
09
Inhaltsverzeichnis
