Glider.it Diana 3 Gebrauchsanweisung

www.glider-it.com

Construction manual

-Place a pad on your workbench to protect the surface of your model

- Then you can start with the removal of the wings. In the example

shown here, K T – X10 are installed on the flaps and on the inner

ailerons. K T - H 08A are used on the outer ailerons. Prepare the servo

frames and grind them thoroughly at the bottom and on the side edges.

This is the only way to ensure a proper adhesive bond.

- Next, they glue a frame made of crepe tape around the servo shafts.

This is for protection and is needed to mark the exact positions of the

servo frames.

- The edges of the servo bay can be slightly reduced. Original have this

6mm width. If you shorten this to half, it makes it easier to install the

servo frames

- The recesses for the rudder horns are already prepared as standard.

These are used for orientation and the position of the servo frame is

marked. With the help of a geotriangle, a line (90 degrees to the hinge) is

drawn

In the outer ailerons, the rudder horns come to the bottom (classic

linkage) and there the position can be transmitted directly

-On the flaps and the inner ailerons, the rudder horns come to the top

(crossover linkage) and there the position must first be transferred from

the top to the bottom.

-To do this, as explained above, they draw a line at a 90-degree angle to

the hinge. tarting from the recess for the rowing horn.

- They draw this line to the end bar and then transfer the position to the

lower shell

From this point, in 90 degrees to the hinge, you can then draw the

required lines

- Next, roughen the surface in the servo shaft and then all adhesive

surfaces (servo bay and servo frame) are degreased

In the next step, the servo frames are prepared for gluing.

There are 2 possibilities: Either they wet the servos with release wax or

they wrap them in cling film. If this is not done carefully, you will not get

the servos removed later because they are firmly glued.

- Now all servos are screwed into their frames.

Important: With servo arm, fork head and a linkage (the length of the

linkage does not matter here)

The rear crossbar on the X10 can be omitted. The servo is fixed at 3

points (2 screws + the counter bearing) and this is sufficient

- Now the 6 servo frames can be glued in. For this they either use Uhu

Endfest or you mix a mumble of 24h resin with cotton flakes and some

thixotropic agent.

If your glue is ready, wet the places in the servo bay and the servo

frames with the glue with a brush. Place the servo frames in the desired

position and align it cleanly with the help of the previously drawn lines.

- After everything is in it, the position is checked again and the whole

thing is weighed down a little.

For this you can use small cups with 100g - 200g lead in each

- Once the whole thing has hardened, the ribs of the counter bearings

are glued to the lower shell.

For this again use an adhesive or mummy. It is important that this must

be touched very toughly, it must no longer flow. Pull the glue into a small

syringe. This makes it easy to bring the adhesive to the desired position.

- It is important here that no glue comes to the ball bearing

- When everything has hardened, the installation of the rowing horns

continues

Before the rudder horns can be positioned, the prefabricated cut-outs

must be reworked a little

Andere Glider.it Flugzeug Handbücher

Glider.it

Glider.it ASW 15 Bedienungsanleitung

Beliebte Flugzeug Handbücher anderer Marken

Cessna

Cessna U206G STATIONAIR Betriebsanleitung

Cirrus

Cirrus SR22 Bedienungsanleitung

Schleicher

Schleicher ASK 21 Montageanleitung

Aircraft

Aircraft REIMS F152 Technische Daten

Skywalk

Skywalk Tequila 2 Bedienungsanleitung

MAULE

MAULE M-7-235B Technische Daten

Ozone

Ozone Indy Handbuch

Tecnam

Tecnam P92 Echo Super Bedienungsanleitung

Wills Wing

Wills Wing HP II Bedienungsanleitung

Ozone

Ozone Roadster Handbuch

Cirrus

Cirrus SR20 Bedienungsanleitung

Niviuk

Niviuk KOYOT 3 Bedienungsanleitung

Pipistrel

Pipistrel ALPHA Trainer Bedienungsanleitung

REVELL

REVELL SnapTite BLUE ANGELS F-18 HORNET Bedienungsanleitung

Cessna

Cessna 172 Series 1973 Bedienungsanleitung

Sky

Sky EOLE Bedienungsanleitung

Sabfoil

Sabfoil Surf Foil Bedienungsanleitung

Cessna

Cessna 182S Skylane Kurzanleitung zur Einrichtung