Global Fire Equipment INT-TCP/IP-WEB Merkblatt

INT-TCP/IP-WEB

REMOTE ACCESS

TCP/IP INTERFACE

MANUAL 210622

MADE IN PORTUGAL - EU

GLOBAL FIRE EQUIPMENT S.A.

Sítio dos Barrabés, Armazém Nave Y, Caixa Postal 908-Z, 8150-016 São Brás de Alportel - PORTUGAL | Tel: +351 289 896 560

Email: info@globalfire-equipment.com | Technical Support: techs@globalfire-equipment.com | www.globalfire-equipment.com

CONFIGURATION MANUAL

GENERAL DESCRIPTION 2

TECHNICAL SPECIFICATIONS 2

CONNECTION DIAGRAM 3

PANEL CONFIGURATION 3

BMS port configuration - ODYSSEY Protocol 3

INTERFACE CONFIGURATION 4

LEDs behaviour 4

Startup behaviour 4

Operation behaviour 4

Configuration using Wi-Fi with module in AP MODE 5

Factory reset and Wi-Fi configurations reset 8

Connecting with Ethernet cable (RJ45) 8

Email or SMS Alerts 9

Service www.clickatell.com (SMS) 9

Firmware update by micro SD card (recommended method) 9

Firmware update via Wi-Fi 10

WEBPAGE ACCESS AND CONFIGURATION 11

FREQUENTLY ASKED QUESTIONS - DIAGNOSTIC 13

Advanced Debug Mode 13

Unlock ports 13

Troubleshooting guide lines 13

INT-TCP/IP-WEB / CONFIGURATION MANUAL / © GFE 210622 1

GENERAL DESCRIPTION

The INT-TCP/IP-WEB is an interface that extends new advanced features and functionalities to Chameleon Panels (GEKKO

and OCTO+). Its enhanced hardware allows for an easier integration with existing LANs via Wi-Fi or optional Ethernet cable.

An SD Card socket permits the interface to hold and store valuable data or simple firmware upgrades when needed. This is

extremely handy on network debug and log needed situations.

Using our proprietary ODYSSEY protocol for Panel communication and a secure connection to a dedicated internet broker

(external server), it is possible to receive “Live” events and monitor the connected panels 24/7, controlling and viewing in real

time the panel status. The user-friendly dedicated webpage via internet browser provides a new and safe level of customer

experience. The new added features, such as SMS and e-mail alerts, will push the remote monitoring capabilities even

more.

Interface configuration network, remote internet broker address, and all local parameters are all configured by means of an

user friendly config web page that can be accessed directly by Wi-Fi AP mode (the interface must be in Access Point mode)

TECHNICAL SPECIFICATIONS

INT-TCP/IP-WEB

SUPPLY VOLTAGE

20 to 30 V DC

SUPPLY CURRENT

28 mA

CONFIGURATION

Remotely via Wi-Fi, Web page

COMMUNICATION CONNECTOR

Ethernet RJ45, Wi-Fi 2,4GHZ, BLE (Bluetooth Low Energy as future dev)

INPUT

Reset as default (advanced configurations)

OPERATING TEMPERATURE

-10ºC to 50ºC

DIMENSIONS

90 © x 40 (A) mm

WEIGHT

24 g

COMPATIBILITY

Windows XP/7/8/10, MacOS, Linux, Android, IOS

PANEL COMPATIBILITY

OCTO+, GEKKO, G-One and NODE+

INT-TCP/IP-WEB / CONFIGURATION MANUAL / © GFE 210622 2

CONNECTION DIAGRAM

Interface power and communication is routed via a 5 way flat cable that’s connected to a 5 pin molex connector available

at panels communication channels. The BMS configurable channels are: CH1 or 2 (GEKKO and CHAMELEON REP) and CH1,

2 or 3 (OCTO+).

PANEL CONFIGURATION

Panel communication uses our ODYSSEY protocol, which is available/selectable in any of the BMS channel.

BMS port configuration - ODYSSEY Protocol

After connecting the interface to the BMS channel, the panel address and ODYSSEY protocol must be selected in order to allow the

communication between panel and webpage. Panel menu 8-5-6 BMS setup.

BMS Channels:

BMS - (CH 1 or 2) - GEKKO

BMS - (CH1, 2 or 3 ) - OCTO+

ADD = 01

Please refer to panels Installation

Manual to learn more about the

BMS channels.

8-5-6 BMS Setup

Use ▲ , ▼ and ► to configure

CH2 : ODYSSEY ADD:01

Warning: Panel will reboot at the end.

Fig. 1 - BMS Menu

INT-TCP/IP-WEB / CONFIGURATION MANUAL / © GFE 210622 3

INTERFACE CONFIGURATION

LEDs behaviour

Startup behaviour

GFE-TCP-IP-WEB

LED 2

(Yellow)

LED 1

(Red)

DESCRIPTION

LED 2 (Yellow)

LED 1 (Red)

OFF

No power

AP Configuration or Startup

FLASHING

OFF

AP firmware Update

FLASHING

Initializing (or wrong settings if

blocked in this stage)

FLASHING

Not used

Operation behaviour

GFE-TCP-IP-WEB

LED 2

(Yellow)

LED 1

(Red)

DESCRIPTION

LED 2 (Yellow)

LED 1 (Red)

OFF

No power

The interface was reset by the

switch. Wait 5 seconds.

FLASHING x2

Without Odyssey protocol.

FLASHING x3

No communication.

No Internet.

FLASHING

1HZ

OFF

Normal Mode

INT-TCP/IP-WEB / CONFIGURATION MANUAL / © GFE 210622 4

Configuration using Wi-Fi with module in AP MODE

ATTENTION:

- DURING THE CONFIGURATION PROCEDURE THE ETHERNET CABLE SHOULD NOT BE CONNECTED.

- The interface comes by default as an Wi-Fi network access point mode. You must associate a computer

with this “AP mode” wifi network to gain access to the interface configuration page.

- Every 30 minutes the interface will automatically restart (Time out) if no configuration has been

programmed. A new connection will be needed.

- In case of malfunction we recommend the use of a micro SD card to easily access config.txt and debug.txt

files. This is not mandatory. Please check the Advanced Debug Mode chapter of this manual.

1) Connect the interface to panel’s BMS channel (ODYSSEY).

2) Both LEDs will flash once on restart. Wait until both LEDs are in the

fixed position, without flashing.

3) Using your own personal device (Ex.Computer, Tablet or mobile

phone) search in the Wi-Fi networks for the interfaces SSID MAC

address. This can be identified as “GFE-AP-XX:...:XX:XX”.

As an example in the image above there is one interface connected (MAC address), select the interface to your Wi-Fi

network, it’s an open Wi-Fi network without the need of a password.

INT-TCP/IP-WEB / CONFIGURATION MANUAL / © GFE 210622 5

4) Once a connection has been established with the interfaces “AP” MAC

address, open a Web Browser and enter the configuration page IP address

http://192.168.4.1

5) Push “Configure Interface” wait a few seconds and a new page will

load. You are now ready to begin programming.

6) All the Wi-Fi networks that the interface was able to detect on site will

appear, as well as the configuration parameters.

7) Select a Wi-Fi network to be used with the interface, if it's a protected

network, enter a network access password. The lock symbol means that

the network is protected, it is also possible to view the percentage of the

signal strength.

ATTENTION:

- Always select a Wi-Fi network that has a signal strength

greater than 20%.

- If you do not want to add any WIFI please assign "0" to the

SSID (WIFI OFF).

- Double Check if the panel is already configured as

ODYSSEY (menu 8-5-6) and have a BMS ADD = 01.

8) Optional: it is possible to configure or add a Wi-Fi network that is not

present in the search page. The interface can be programmed offline and

as soon as it is connected, the interface will detect the configured SSID to

the selected wifi network.

9) NETWORK: choose the connection type, value 0for RJ45 cable

connection, value 1for Wifi connection.

10) DHCP Set a value of 0 to activate or a value of 1 to off.

11) IP Address - if you choose a connection without DHCP and cable

(RJ45) configure a valid IP address.

12) Subnet Address. configure a subnet address in case of cable

connection and without DHCP enabled.

13) Gateway Address. configure a valid Gateway address in case of

connecting via RJ45 and without DHCP.

14) DNS_1- configure the primary DNS address for cable connection and

DHCP disconnected.

15) DNS_2- configure a secondary DNS address for RJ45 connection and

DHCP disconnected.

16) BROKER: remote.createc.pt

17) PORT: 8883

18) USER: B5D7F3

GFE_AP-4C:11:AE:6E:2C:70

Interface GFE TCP/IP Wi-Fi Configurator

Configure Interface

Available Networks:

GFETEC_AP_1

GFETEC_AP_GUESS_1

broker AP

NOS-73D6

ZON-B360

MEO WiFI

(...)

🔒

82%

🔒

72%

🔒

66%

🔒

56%

🔒

42%

28%

...

INT-TCP/IP-WEB / CONFIGURATION MANUAL / © GFE 210622 6

19) PASSWORD: C9E3F6

20) CHANNEL: The name of the channel, can be a name of your choice.

Or use “Channel” as default.

21) ALERT TYPE: to assign how you prefer to receive alerts. The value 0

to receive email alerts, the value 1to receive SMS alerts, the value 2to

receive alerts by email and also by SMS, other any value or no value to

turn off the alerts feature.

22) EMAIL RECIPIENT: to enter the email that wants to receive the email

alerts.

23) SMS API ID: enter the API KEY number of the SMS sending service.

Registration must be made at www.clickatell.com

24) SMS USER: enter the user name of your SMS sending server account.

25) SMS PASSWORD: enter your sms sending service account password.

26) SMS TO: enter the phone number you want to send the alert by SMS.

The number must have the country's code. For example, for Portugal it

should be entered the code 351 before the number, example:

351960000000.

27) Press the "Save" button to save the settings.

The interface is now configured and associated with a Wi-Fi network,

the interface will restart with the configured settings. Both LEDs will start

flashing when the communication between interface and the internet

broker (external server) has been established. Whenever it is not

possible for the interface to connect to the configured network, it will

make several attempts before going into access point mode.

You can now access remotely to https://www.createc.pt/gk1/gfe/en/ and

follow the “CONFIGURATION: WEB PAGE” section of this manual.

Credentials and Setting saved.

Trying to connect Wired to network.

If it fails reconnect to AP to try again.

Version Firmware: 1.2.1

INT-TCP/IP-WEB / CONFIGURATION MANUAL / © GFE 210622 7

ATTENTION:

- All settings parameters must be assigned correct values. The Client ID param, that will be requested at the

website, is indicated on the configuration page when set in Configuration AP Mode.

NOTE: The Client ID is the MAC ADDRESS inverted

Factory reset and Wi-Fi configurations reset

At any time you can delete/correct any settings, the procedure is as follow:

1) Power the interface using the dedicated communication channel.

2) Wait for the two LEDs (red and yellow) to light up, press and hold the "Restart" button for a period of 2

seconds until the yellow LED turns OFF, stop pressing the button at this point.

3) The red LED will stay ON permanently for 5 seconds and the interface will now restart in access point mode

with all the settings erased.

Connecting with Ethernet cable (RJ45)

1) The settings procedure should be always programmed via Wi-Fi, as previously described. Only connect the

interface cable after power is OFF.

2) Turn interface power ON (using panel).

3) Wait for both LEDs to start blinking. When the two LEDs flash alternately the interface is communicating with

the server.

ATTENTION:

- DURING FIRMWARE UPDATE PROCEDURE THE ETHERNET CABLE SHOULD NOT BE CONNECTED.

- The connection to the internal network should allow the interface to be connected by DHCP with access to

the exterior. If this is not possible the interface cannot communicate with the internet broker (external

server).

INT-TCP/IP-WEB / CONFIGURATION MANUAL / © GFE 210622 8

Email or SMS Alerts

Starting with firmware version 1.1.1, the interface can send alerts by SMS or by email, or in both modalities. For alerts to be

enabled, you must make the respective settings. The alerts you receive, is a short text message describing what originated

the alert, and identifies who sent by the client ID and channel configured in the interface. The alerts you can receive are as

follows:

● When the interface starts communications with the internet broker (external server).

● When the panel on fire, and also when I came out of the fire alarm.

● When the panel fails and then when I left the failed state.

● When the panel disabled and then when I left that state.

● When the panel a pre-alarm or when I'm out of that state.

● When the panel test mode or then when I left like this.

● When communication begins with the panel and the System LED is turned on.

ATTENTION: There are no guarantees of receiving alerts. If the connection to the mail or SMS server is not possible,

the alert will not be sent, but the interface continues with its normal operation. For SMS server detailed function

please check www.clickatell.com for further info.

Service www.clickatell.com (SMS)

1) Access to client area and, after register and login, go to Workspace

2) Verify or add in “Test Phones” all desired phone numbers to be used

3) Go to “Channels->SMS” and on “My SMS Setups” add the new user/interface, it will be shown the

API KEY needed to be configured on the interface.

Firmware update by micro SD card (recommended method)

You can update the interfaces firmware with a micro SD card, format FAT32, the procedure is as follow:

1) Save the update firmware file "upgrade.bin" to the micro SD card.

2) Turn interface power OFF, and insert the micro SD card into its socket.

3) Turn interface power ON. If the file is valid the update starts Automatically.

ATTENTION: NEVER RENAME OR CHANGE the file name. Do not turn power OFF while updating the firmware, it

may cause the interface or micro SD card to malfunction.

4) Wait a few seconds, the red LED will always be ON and the yellow LED will always be OFF until the update

is complete. The update file at the end of the process will be automatically deleted from the card.

5) At the end of the update, the interface will automatically restart. The LEDs will start flashing and soon after

both LEDs will be fixed in ON position.

6) Turn the interfaces power OFF.

7) Turn power ON to reconnect, the interface will start with the new firmware in "AP" mode.

Firmware update via Wi-Fi

A firmware update can be transferred to the interface via a Wi-Fi network. The procedure is as follow:

1) Turn interface power ON, the two LEDs red and yellow will light

up, as soon as the yellow LED will goes OFF, press the "restart"

button and hold it, until the red LED is completely OFF. Stop

pressing the button then.

2) The red LED will blink ON and OFF, the yellow LED will remain

ON, the interface is now ready to be updated via Wi-Fi.

3) Search in Wifi network for the interface SSI MAC address,

this can be identified as "GFE-UP-X:X:X" or "GFE-AP-X:X:X", the

X:X:X Its an open Wi-Fi network without the need

of a password.

4) Once a connection has been established with the interfaces “AP”

MAC address, open a Web Browser and enter IP address

192.168.4.1

5) In the web page, use the login details for "User ID "as gfe and

"Password" as efg, click on "Login" to enter the update page.

6) Click on "Choose file..." and search in your local folder/desktop for

the firmware update file as "upgrade.bin".

7) Click the "Update" button, to begin the firmware update.

8) It's possible to view the update progress in the "green" bar, please

wait until it reaches 100%.

9) After a few seconds the two LEDs red and yellow, will be

permanently turned ON. The interface is now updated with firmware

and prepared in AP mode for the new settings.

User ID

Password

Choose file...

Update

upgrade.bin

Update

progress 30%

upgrade.bin

Update

progress 100%

ATTENTION: The interface in normal operation, if you press the switch for 2 seconds, within 2 to 4 seconds the

interface will reset. At the time of the reset the switch should be released.

Inhaltsverzeichnis

Andere Global Fire Equipment Feuerlöschausrüstung Handbücher

Global Fire Equipment

Global Fire Equipment ORION MINI-REP V2 Gebrauchsanweisung

Global Fire Equipment

Global Fire Equipment ADLI V2 FO Betriebsanleitung

Global Fire Equipment

Global Fire Equipment Valkyrie Vox C Bedienungsanleitung

Global Fire Equipment

Global Fire Equipment GFE-PA-VOX-A Bedienungsanleitung

Global Fire Equipment

Global Fire Equipment ZEOS-AS-S Bedienungsanleitung

Global Fire Equipment

Global Fire Equipment VALKYRIE CB IP65 Bedienungsanleitung

Beliebte Feuerlöschausrüstung Handbücher anderer Marken

Tyco Fire Protection Products

Tyco Fire Protection Products AM31 AQUAMIST Nozzle Bedienungsanleitung

Task Force Tips

Task Force Tips Extend-A-Gun RC3 Betriebsanleitung

Autronica

Autronica AutroSafe BSD-321/EX Bedienungsanleitung

POK

POK Froggy Bedienungsanleitung

Waterous

Waterous AQUIS Series Handbuch

CTP

CTP NPO ETERNIS GUARANT-7 Stücklistenhandbuch

MSA

MSA M1 Bedienungsanleitung

Grundfos

Grundfos Hydro EN Betriebsanleitung

Amerex

Amerex 570 Anwendungshandbuch

Vimpex

Vimpex BIG HP18-H200-B1 Bedienungsanleitung

Chubb

Chubb PEFS F3 Bedienungsanleitung

Projoy Electric

Projoy Electric PEFS-PL Series Bedienungsanleitung

klimaoprema

klimaoprema FDC25 Series Bedienungsanleitung

Mueller

Mueller Revive M2 Bedienungsanleitung

SEI Industries

SEI Industries BAMBI MAX BBXHL4000PF Bedienungsanleitung

Waterax

Waterax MARK-3 Bedienungsanleitung

Tyco

Tyco 802SB Bedienungsanleitung

Apollo

Apollo Smoke Detector XP95 Bedienungsanleitung