Global VR Six Gun Select Bedienungsanleitung

Six Gun Select

Joshua OS Upgrade

Full Cable Conversion

040-1102-01 Rev. C

www.globalvr.com

[email protected]

1-408-597-3400

Reserved. All other trademarks are the property of their respective owners.

Safety

The following safety instructions apply to all game operators and service personnel. Specific warnings

and cautions will be found throughout this manual.

Please read this page before preparing your arcade cabinet for game play.

Use the following safety guidelines to help protect the system from potential damage and to ensure your

personal safety.

• To help avoid damage to the computer, the power supply on the computer automatically detects the

voltage to match the AC power available at the location:

• 115 volts / 60Hz in most of North and South America and some Far Eastern countries such as Japan,

South Korea and Taiwan

• 230 volts / 50Hz in most of Europe, the Middle East and the Far East

• To help prevent electric shock, plug the system into a properly grounded power source. These

cables are equipped with 3-prong plugs to help ensure proper grounding. Do not use adapter plugs

or remove the grounding prong from a cable. If you must use an extension cable, use a 3 wire cable

with properly grounded plugs.

• To help protect your system from sudden increases and decreases in electrical power, use a surge

suppressor, line conditioner or Uninterruptible Power Supply (UPS).

• Be sure nothing rests on the system's cables and that the cables are not located where they can be

stepped on or tripped over.

• Do not spill food or liquid on the cabinet.

• Do not push any objects into the openings of the system. Doing so can cause fire or electric shock by

shorting out interior components.

• Keep your computer far away from radiator and other heat sources.

• Do not block cooling vents.

Warnings

To avoid electrical shock, unplug the cabinet before performing the

installation procedures.

Global VR assumes no liability for any damages or injuries incurred

while setting up the EA Sports™ PGA Tour® Golf cabinet. Only

qualified service personnel should perform this installation!

Six Gun Select Joshua OS Upgrade

2040-1102-01 Rev C 4/27/2004

Installing Gun ESD Protection

To protect the Gun and Gun Module from electrical shock you will need to install the Gun ESD PCB into

your cabinet. Follow the instructions below.

1. Make sure the cabinet is powered down and the AC unplugged from the wall outlet.

2. Locate the 5-pin Molex connector that connects the gun harness to the gun module.

3. Unplug the Molex connectors. Remove the male joiner pins as shown by the arrow in Part 2 and 3 of

the picture above

4. Install the ESD PCB next to the gun harness. Use wood screws to attach the PCB to the cabinet. The

green ground wire on the PCB should point down. See Part 4 of the picture above. The gun harness

should be able to reach the ESD PCB.

5. Plug the gun harness connector into the top of the ESD PCB. See Part 5 of the picture above. Plug

the gun module connector into the bottom of the ESD PCB.

6. Connect the grounding wire from the ESD PCB to the ground stud on the AC Power plate at the rear

of the cabinet. See part 6 of the picture above. This is a critical part of the ESD protection.

Six Gun Select Joshua OS Upgrade

040-1102-01 Rev C 4/27/2004 3

Installing Six Gun Select Cabinet Artwork

Replace the old Last Bounty Hunter artwork with the new Six Gun Select artwork included with your kit.

The new artwork installs over the old artwork to make this process as simple as possible.

1. Use the marquee to align the bottom edge of the new artwork and apply as shown in the picture

above. If the new artwork hangs over the edge of the marquee, use a razor blade to trim the excess.

See Item 1 in the picture above.

2. Apply the new console artwork between the two speakers on the front of the cabinet. Ensure the new

console artwork completely covers the old artwork. See Item 2 in the picture above.

3. Apply the new side art graphics on both sides of the cabinet. Use the top corner of the Six Gun Select

logo to align the new artwork on the cabinet. Ensure the new artwork completely covers the old

artwork. See Item 3 in the picture above.

4. Apply the game logo sub-console artwork across the front of the cabinet just below the speakers. See

Item 4 in the picture above. This artwork shows players the available games. Each new game you

purchase comes with a small sticker that is placed on this area.

Six Gun Select Joshua OS Upgrade

4040-1102-01 Rev C 4/27/2004

Upgrading Computer and Cabinet Hardware

1. Make sure the cabinet is powered down and the AC unplugged from the wall outlet before you begin

the hardware upgrade.

2. Unplug the video cable, USB I/O cable, and DB-37 connector from the back of the computer as

shown by the arrows in the following picture. Plug the video cable into the 15-pin monitor port on the

computer.

3. The DB-37 connector is one end of the game harness. The entire game harness must be removed

from the cabinet. Perform these steps to remove the old game harness:

– Cut the tie-wraps holding the harness in place.

– Unplug the 9-pin connector from the audio Amp card.

– Unplug the 6-pin connector from the audio Amp card.

– Unplug the power cable that wraps around to the front of the audio Amp card.

– Unplug the 2-pin connector (the adjacent 3-pin connector is unconnnected).

– Remove the harness from the cabinet.

4. Remove the two screws holding the side panel onto the computer. Slide the computer side panel

back first then out to unlock the panel from the computer case.

5. Remove the AGP video card.

6. Unplug the power cable from the USB I/O card, and remove the USB I/O card. Return the video card

and USB I/O card to receive credit towards the Joshua Upgrade kit.

7. Re-install the computer side panel onto the computer chassis.

8. Install the LBH Coin PCB on the cabinet side wall using (4) 1" wood screws. See the following picture.

Six Gun Select Joshua OS Upgrade

040-1102-01 Rev C 4/27/2004 5

5-Pin Gun Harness Connector

(New ESD PCB not shown)

New Conversion Harness

(Part# 115-0014-01 Rev. C)

DB-25 Connector

Gun Module

New LBH Coin PCB

with 12-Pin Connector

New Computer

Power Supply Monitor Cable

9-Pin and 6-Pin Connectors

from Game Harness

to Audio Amp Card

Power Cable from Game

Harness wraps around to front

of Audio Amp Card

2-Pin Connector

from Game Harness

Connect Ground Wire from Game

Harness to Ground Stud on

r Pl

Coin Box Ground Stud

9. Install the computer power supply on the cabinet floor next to the computer and LBH Coin PCB using

the velcro provided in the kit.

10. Connect the 4-pin power cable from the power supply you just installed to the LBH Coin PCB.

11. Install the new conversion harness (Part# 115-0014-01 Rev. C) using the following steps. Refer to the

photo above:

– Plug the DB-25 connector on the harness into the computer parallel port.

– Connect the first ground wire on the harness to the AC power plate ground stud.

– Plug the 12-pin connector on the harness into the new LBH coin PCB.

– Plug the 9-pin connector on the harness into the 9-pin connector on the audio Amp card.

– Plug the 6-pin connector on the harness into the 6-pin connector on the audio Amp card.

– Plug the 2-pin connector on the harness into the button harness (next to the gun harness).

– Connect the power cable on the harness to the front of the audio Amp card.

– Connect the second ground wire on the harness to the coin box ground stud.

12. Use tie-wraps to secure the new cable harness in place.

Six Gun Select Joshua OS Upgrade

6040-1102-01 Rev C 4/27/2004

Changing Computer BIOS Settings

After completing the hardware upgrade, you must verify that the parallel port setting in the computer BIOS

is correct. This will ensure proper operation of the coin inputs and operator buttons.

1. Power to the computer must be OFF. Plug the PS/2 Keyboard into the purple-colored PS/2 port on

the back of the computer.

2. Power the computer ON. Hit the Delete key on the keyboard when you see the first boot-up screen

showing the CPU speed and memory. This will start the BIOS Setup Menu. See the following picture.

3. Use the arrows keys to scroll down and highlight Integrated Peripherals. Press the Enter button to

enter this menu.

4. At the Integrated Peripherals Menu screen use the arrow keys to scroll down the long list of available

options until you find Parallel Port Mode and EPP Select Mode. Use the Page Up and Page Down

keys next to the number pad to scroll through and change each option.

5. Parallel Port Mode must be set to EPP and EPP Select Mode must be set to EPP 1.7. After

changing these values, press the F10 Key to exit setup and save settings.

6. You may now unplug the keyboard from the computer and load the new software.

Upgrading the Software

Use the following procedure to install the software upgrade:

1. The cabinet should be powered ON and the game running. Open the CD drive and insert the CD

labeled Six Gun Select - Joshua Operating System/Game Software CD. Power the cabinet OFF

then ON. When the computer reboots, the CD should automatically start up.

2. At the Install Menu, use the Operator Up/ Down and Select buttons to choose one of the following

options:

– (1) Install and Format. Use this option when upgrading the software. It will erase all previous

game and coin collection information on the computer and start over. You will need to re-install

any other games after this step.

– (2) ADD / Update Games – use this option to install the new games on the cabinet without

erasing any of the games that are currently installed or coin collection info. Once the new game is

installed it will automatically become available in the game selection menu in the game attract

mode.

Six Gun Select Joshua OS Upgrade

040-1102-01 Rev C 4/27/2004 7

3. When the hard-drive imaging process is complete, the game software will automatically start.

Remove the CD from the computer and keep in a safe place.

4. When the game starts up for the first time, it is important to synchronize the new game software with

the cabinet’s hardware. This is done by coining up the machine (insert 2 credits), then verifying that

the two credits are shown (for example, $0.50) on the monitor. Finally, power the system OFF and

then ON to complete the synchronization process.

In the event the software running on the computer becomes corrupt, or you run into software problems,

you can use the CD to reinstall the software.

Return Items after Joshua OS Upgrade Kit Installation

For your convenience we have enclosed a prepaid self-addressed envelope with the Joshua OS Upgrade

kit. Please use this envelope to return the old hardware listed below.

If you ordered the Joshua OS Upgrade kit you will need to return the old hardware that was installed on

your LBH computer to Global VR. Please include all items form the list below to receive a full credit

towards your account. Global VR will deduct the retail value for any hardware item that is not included in

your return from your account.

– (1) Nvidia Geforce 2 Video Card

– (1) USB I/O Card

– (1) LBH KQRTG USB Game Dongle

Note: You have been invoiced for these parts. In order to receive full credit towards your account

you must return these items to GLOBAL VR within 30 days of receipt of this kit.

Please fill out the bottom section of this sheet and send it back with the parts to Global VR.

Name:

Company Name:

Street Address:

City, State, Zip:

Phone Number: ( )

Distributor:

Serial Number on

Game:

Serial Number is located on

the upper back left corner of

the cabinet Thank You

Six Gun Select Joshua OS Upgrade

8040-1102-01 Rev C 4/27/2004

Inhaltsverzeichnis

Andere Global VR Arcade-Spielautomat Handbücher

Global VR

Global VR America's Army Montage- und Bedienungsanleitung

Global VR

Global VR Blazing Angels Green Label WWII Montage- und Bedienungsanleitung

Global VR

Global VR Need For Speed GT Standard Bedienerhandbuch

Global VR

Global VR EA SPORTS MADDEN NFL FOOTBALL Benutzerhandbuch

Global VR

Global VR Aliens Extermination Montage- und Bedienungsanleitung

Global VR

Global VR Aliens Extermination Benutzerhandbuch

Beliebte Arcade-Spielautomat Handbücher anderer Marken

Universal Space

Universal Space COCONUT BASH Bedienungsanleitung

Bay-Tek

Bay-Tek EVOLVE Bedienungsanleitung

Atronic

Atronic Cashline Bedienungsanleitung

Universal Space

Universal Space Checky Monkey Bedienungsanleitung

Bay-Tek

Bay-Tek Skee Ball 1908 Alley Bedienungsanleitung

Aristocrat Technologies

Aristocrat Technologies Mars X Upright Bedienungsanleitung

Family Fun Companies

Family Fun Companies Reactor Kurzanleitung

Universal Space

Universal Space FRUIT MANIA Extreme Bedienungsanleitung

falgas

falgas CARRUSEL FIESTA Bedienungsanleitung

Konami

Konami DanceDanceRevolution Bedienungsanleitung

Bay-Tek

Bay-Tek quik drop Bedienungsanleitung

Bandai Namco

Bandai Namco PAC-MAN BATTLE ROYALE CHOMPIONSHIP DELUXE Bedienungsanleitung

Adrenaline

Adrenaline Flying Tickets Montage- und Bedienungsanleitung

Swinks

Swinks Stern Pinball Ghostbusters Bedienungsanleitung

Innovative Concepts in Entertainment

Innovative Concepts in Entertainment MONOPOLY ROLL-N-GO Bedienungsanleitung

jakar

jakar SPEED CARS Bedienungsanleitung

Carmelli

Carmelli HAT TRICK NG1015H Bedienungsanleitung

CA RING TOSS Bedienungsanleitung