GLP Junior Scan 3 Bedienungsanleitung

Instruction Manual

from software version 1.0

(instruction version 0.91)

email: servic[email protected]

Internet: http://www.GLP.de

1(instruction version 0.91) GLP zGerman Light Production

This side is intentionally unlabelled.

GLP zGerman Light Production (instruction version 0.91) 2

Table of contents

1Description of the Device....................................................................................... 4

1.1 Safety Instructions............................................................................................ 5

2Preparation and Installation................................................................................... 6

2.1 Mounting........................................................................................................... 6

2.2 Secure the J

3........................................................................... 6

2.3 Connectors ....................................................................................................... 6

2.3.1 Power supply ......................................................................................... 6

2.3.2 DMX....................................................................................................... 6

2.4 Fuses................................................................................................................ 6

3The Menu Field / DMX Address and Functions .................................................... 7

3.1 Adjust the DMX- Address (D001)....................................................................... 8

3.2 The Test Program (TEST) .................................................................................. 8

3.3 The Audio Program (AUDI) ................................................................................ 8

3.4 Lamp On/Off (LAMP) .......................................................................................... 9

3.5 Reset (RESE)...................................................................................................... 9

3.6 Running time of lamp and unit (TIME) ............................................................... 9

3.7 Invert Pan Movement (RPAN) ............................................................................. 9

3.8 Invert Tilt Movement (RTLT) ............................................................................ 10

3.9 Special Functions (SPEC)................................................................................. 10

3.9.1 Manual Drive (MANU) ............................................................................. 10

3.9.2 Lamp On automatically (LAAU) .............................................................. 11

3.9.3 Lamp Off via DMX (DLOF) ..................................................................... 11

3.9.4 DMX Input (DMXI).................................................................................. 11

3.9.5 Display (DISP)....................................................................................... 12

3.9.6 Adjustments and Calibrations (ADJU) .................................................... 12

3.9.7 Default Settings (DFSE) ......................................................................... 13

3.9.8 Correction of faults (EFLG) .................................................................... 13

3.10 Error and Information Messages .................................................................... 13

3(instruction version 0.91) GLP zGerman Light Production

4DMX Channel Selection (DMX Protocol)............................................................. 14

5Change the Lamp.................................................................................................. 17

5.1 Safety Regulations ......................................................................................... 17

5.2 Realize the Lamp Change.............................................................................. 17

6Change a Gobo ..................................................................................................... 17

6.1 Safety Regulations ......................................................................................... 17

6.2 Realize the Gobo Change.............................................................................. 18

7Maintenance and Cleaning the J

3............................................... 18

7.1 Safety Regulations ......................................................................................... 18

7.2 Circumference and Interval (rule-of-thumb) ................................................... 18

7.3 Cleaning the Optical System.......................................................................... 19

7.4 Mirror and Optical System.............................................................................. 19

7.5 Fan and Cooling System................................................................................ 19

8Technical Specification........................................................................................ 20

9Index ...................................................................................................................... 21

GLP zGerman Light Production (instruction version 0.91) 4

1 Description of the Device

Display

Data entry

Lens

Relay bracket

Air outlet

2x Air inlets

Casing screws

Figure 1-1

5(instruction version 0.91) GLP zGerman Light Production

1.1 Safety Instructions

The

is a High-Tech Product. To guarantee a

smooth operation, it is necessary to keep the following rules.

The manufacturer of this device will not take responsibility of

damages through disregard of the information in this manual.

Warranty adjustments will be canceled.

1. Make sure before putting into operation, that the fan and the air inlets are

clean and not blocked by anything.

2. Attention: Don’t touch the device during the operation. This can cause injuries

or damages.

3. Unplug the

from the AC outlet before any service.

4. It is necessary to wait at least 30 minutes after disconnecting the AC before

you open the J

3. Please do not touch the bulb of the lamp if

you are not absolutely sure it is cold. -Danger of BURNING-

5. Never look directly into the beam of the lamp. You risk injury of your retina and

blindness.

6. Pay attention of the maximum lamp operation time. You have to change it if

the lamp shows any deformations or damages. The same is with all glass

components, color filters, lenses and mirrors.

7. To allow a secure operation, follow also the Installation guide described in

chapter 2. Operating the J

without suited safety aids like

Safety cables or clamps/hooks can increase the risk of an accident.

8. The installation should be done by qualified staff only. You need to pay

attention to the common rules of technology that are not explicit mentioned in

this manual.

9. Use only original spare parts. Any structural modification will cancel all

warranty adjustments.

GLP zGerman Light Production (instruction version 0.91) 6

2 Preparation and Installation

2.1 Mounting

Mount clamps and/or hooks directly to the mounting (relay) brackets of the

Please make sure to use right sized clamps and hooks and fit

them securely. Keep a safety distance of 0.5 m towards any easy inflammable

materials (decoration etc.).

Pay attention to the regulations of: BGV C1 (former VBG 70)

and DIN VDE 0711-217.

The installation should be done by qualified staff only.

2.2 Secure the

Regardless of the rigging of the J

you have to use a stipulated

safety wire that can hold at least 10 times the weight of the fixture. Install it

through the handle and connect it with the truss-support. Pay attention to a safe

and proper fastening.

2.3 Connectors

2.3.1 Power supply

230 Volt, 50 Hz,

Connected load 370W <=> 2,2 A (blind current compensation).

or 115V, 60 Hz

Connected load 740W <=> 4,4 A (blind current compensation).

2.3.2 DMX

USITT DMX 512 Standard input/output.

[+] = Pin 3 / [-] = Pin 2 / [Ground] = Pin 1

The DMX- Addressing starts at the DMX- Address [001].

2.4 Fuses

The J

electronic system is protected by a 5x20 mm fuse.

230V / T 3,15A (EU model) or 115V / T 6,3A (US model)

Please see the printing on the J

for more details.

Attention:

• Disconnect AC outlet before changing a fuse!

• Use only the original declared fuse type!

7(instruction version 0.91) GLP zGerman Light Production

3 The Menu Field / DMX Address and Functions

You find the control board on the front side of the casing. It allows you

to make all necessary adjustments of the J

.With the

Mode-key you get into the main menu. Afterwards you can navigate

through the menu with the Up/Down-keys. Push the Enter-key to get

in the next menu level or to confirm your settings. Make them and set

functions ON/OFF with the Up/Down-keys. Confirm and save it with

the Enter-key (the display shows OK). Push the Mode-key to cancel the

entry and go back to the main menu.

MODE ENTER UPDOWN

MODEENTERUP DOWN

LED-Display

Level 1 Level 2 Level 3 Remark

D001

Define the DMX start address

TEST

Test program of all functions

AUDI ASLW Self-running audio program (slow)

AFST Self-running audio program (fast)

MSTR Master for the audio program

SVPT Basic position for the audio program

SIZE Size for the audio program (NORM-BIG-MID-SMALL)

LAMP

Switch on/of the lamp direct at the Y

RESE

Reset

TIME POWR Running time of the fixture (no destructible)

LA1 Running time of the lamp (erasable)

LA2 Running time of the lamp (no destructible)

RPAN

Reverse Pan-direction

RTLT

Reverse Tilt-direction

SPEC MANU Manual drive of all device functions

LAAU Automatic lamp start

DLOF Switch off lamp via DMX

DMXI Reed out actual DMX-values

DISP D ON Display On/Off

REV Twist the display

ADJU CODE xxxx Use the code for entering the calibration menu (for

authorized person only)

COLO Calibration of the color wheel

GOBO Calibration of the gobo wheel

PRIS Calibration of the prism wheel

SHT1 Calibration of the shutter 1

SHT2 Calibration of the shutter 2

ÅDOWN - UP Æ

POFS PAN Offset

TOFS TILT Offset

CLRE Settings in the internal memory (super user only)

ARES

ADJUST RESET

DFSE Call on the default function values

TRB1

Software settings for the TRB1 board

TRB2

Software settings for the TRB2 board

EFLG Correction of faults

GLP zGerman Light Production (instruction version 0.91) 8

3.1 Adjust the DMX- Address (D001)

Right after turning on the J

you can see the current DMX-

Address. If there is no DMX- Signal the display flashes.

D001

For the address setting please follow this procedure:

1. Switch On the J

and wait until the fixture reset has finished

('RESE'is flashing in the display).

2. Press the Mode-key in order to access the main menu. Browse through the

menu by pressing the Up/Down-keys until the display shows D001. Confirm by

pressing the Enter-key (the decimal point is flashing)

3. Use the Up/Down-keys to select the desired address. Confirm the setting by

pressing the Enter-key (the display shows OK) or press the Mode-key to

cancel.

The DMX- Address is stored also while switching off the J

3.2 The Test Program (TEST)

Test

The Test-program allows you to run a complete self test procedure of all functions.

Press Enter to confirm or Mode to cancel.

3.3 The Audio Program (AUDI)

Audi

The Audio-menu allows you to run a stand alone audio program. This chaser can

run either fast or slow. AFST: Every sound impulse on step of the chaser. Aslw:

Every second sound impulse one step of the chaser.

Additional you can choose a basic position for this audio chaser. Use therefore

either the internal manual mode or an external controller to set the desired Pan/Tilt

position. Confirm this setting in the SVPT menu by pressing the Enter-key.

You can also set the size of the audio chaser in the SIZE menu. You have the

choice between: NORM (no basic position has to bee chosen), 'BIG', 'MID' and

'SMALL').

9(instruction version 0.91) GLP zGerman Light Production

If you want to run the systems simultaneously, one of the J

must

be switched as the master. All others must be "Slave" Master = OFF. Notice: The

Audio function is only working if no DMX is connected. This function can work e.g.

on small events or as an emergency program.

3.4 Lamp On/Off (LAMP)

LAMP

Use the Up/Down-keys to select lamp On or lamp Off Press Enter to confirm or

Mode to cancel and return to the main menu. (The lamp OFF command is only

working if the shutter is closed at the same time. Use an external controller or the

manual drive mode, see also chapter 3.9.1 on page 10)

3.5 Reset (RESE)

RESE

Press the Enter-key to run a reset of all fixture functions (RST is shown in the

display).

3.6 Running time of lamp and unit (TIME)

TIME

You can read out three different running times of the fixture.

POWR Running time of the fixture (no destructible).

LA 1 Running time of the lamp (erasable). Push the Up/Down-keys at one

time to delete this running time.

LA 2 Running time of the lamp (no destructible).

3.7 Invert Pan Movement (RPAN)

RPAN

This function allows you to invert the Pan movement. Use the Up/Down-keys to

select invert On or Off. Press Enter to confirm or Mode to cancel and return to the

main menu.

Inhaltsverzeichnis

Andere GLP DJ-Equipment Handbücher

GLP

GLP inmpression E 350 Bedienungsanleitung

GLP

GLP impression FR1O BAR Bedienungsanleitung

GLP

GLP impression X4 Bar 20 Bedienungsanleitung

GLP

GLP impression FRIO BAR Bedienungsanleitung

GLP

GLP GT-1 Bedienungsanleitung

GLP

GLP X4 ATOM series Bedienungsanleitung

GLP

GLP YPOC 575 COLOR Bedienungsanleitung

GLP

GLP KNV Series Bedienungsanleitung

GLP

GLP impression x4 bar Kurzanleitung

GLP

GLP Startec-1200 Bedienungsanleitung

GLP

GLP IMPRESSION X4L Bedienungsanleitung

GLP

GLP Fusion EXO Beam 10 Bedienungsanleitung

GLP

GLP IMPRESSION X4L Bedienungsanleitung

GLP

GLP Fusion Stick FS20 Bedienungsanleitung

GLP

GLP impression FR1 TM Bedienungsanleitung

GLP

GLP Fusion Par FP7 Bedienungsanleitung

GLP

GLP Impression E350 Bedienungsanleitung

GLP

GLP Impression Series Bedienungsanleitung

GLP

GLP VOLKSLICHT R-G-B Bedienungsanleitung

GLP

GLP YPOC 250 Color Bedienungsanleitung

GLP

GLP YPOC 575 Bedienungsanleitung

GLP

GLP JDC1 Bedienungsanleitung

GLP

GLP JDC Line 500 Bedienungsanleitung

GLP

GLP JDC Line 500 Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Zumtobel

Zumtobel APHRODITE Home Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung