GMP QTOPIC-380 Bedienungsanleitung
2015. 06
User Manual for QTOPIC-380
Before you operate the product, this manual has to be read by operator.
※ External Design & Specification can be changed for improvement without any prior notice.
INDEX
◐ SAFETY ◐ HOW TO LAMINATE 27~30 page
Important Safety Instruction 3~5 page
Safety Device 6 page ◐ MAINTENANCE 31 page
Warning Sticker 7~8 page
◐ TROUBLE SHOOTING 32~35 page
◐ INSTALLATION
Packing Contents 9 page ◐ SPECIFICATION 36 page
Main Devices 10 page
How to move & install 11~13 page ◐ DIGITAL SLEEKING SOLUTION
SLEEKING SOLUTION Introduction 37 page
◐ HOW TO USE CONTROL PANEL
GLOSS & MATT SLEEKING
38~41 page
Explanation of Control Panel 14~16 page HOLOGRAM SLEEKING 42~45 page
Explanation of Display 17~18 page METALLIZE PRINTING 46~47 page
Error Message 19~20 page SLEEKING FOIL SPECIFICATION 48 page
◐ MAIN DEVICES
Lamination 21~23 page
Cutting 24 page
How to load / replace film roll 25 page
Other Devices 26 page
IMPORTANT SAFETY INSTRUCTION
"Instruction for Safety" is for the purpose of user's safety
and prevention of Property loss. Read thoroughly and Use rightly according to the manual
Important Safety Instruction is classified as "Warning" and "Caution", the meaning is as follows;
Warning : If you ignore this symbol, you could suffer serious injury or death
Caution: If you ignore this symbol, you could receive a serious injury or loss of property
This symbol means a prohibited action. If you ignore a prohibited action, you could suffer a personal injury and damage the machine
This symbol means a required action. If you don't follow this action, your safety is not guaranteed.
Required action will be included in this symbol.
Reference: The sign above refers the contents for user's safety and prevention of Property loss.
3/48
IMPORTANT SAFETY INSTRUCTION
Do not connect or disconnect with wet hands, as this will cause an electric shock
Do not overload a power supply, as this will cause a fire and an electric shock.
Do not use a damaged plug or lead, as this could cause a fire or an electric shock
Do not use other voltage and power supply other than specified, as this will cause a fire and an electric shock.
Make sure plug is in the socket, as it could cause fire or an electric shock
Grounding is needed for your safety
A malfunction and losing electricity make an electric shock
Danger, Malfunction, loss of electricity could cause an electric shock
Do not pull the plug or bend improperly
Do not use materials near a naked flame
Do not use the machine in the sealed place.
Only use the specified power and voltage. It can be a reason of fire flame or an electricity fire flame.
Do not dissemble, make repairs or convert the machine. Contact your dealer for repairs
Ensure all hair, neckties, necklaces, are kept free of the feeding table to avoid injury
Do not convert the safety device and safety switch.
Do not spill any liquids on the laminator as this will cause damage and a possible electric shock
Do not use the flammable spray or flammable materials inside or outside the machine. As this could cause a fire.
Do not allow children use of this equipment
WARNING
GROUNDING
P
O
W
E
R
I
N
S
T
A
L
L
A
T
I
O
N
4/48
IMPORTANT SAFETY INSTRUCTION
When moving the product, turn off the power switch, disconnect the power plug from the socket
When laminator is not in use, you must turn off the power switch, disconnect the power plug from the socket.
More than 2 people are needed to carry this equipment to avoid personal injury or damage to the machine.
Keep gears and chains free of all materials
Do not touch the roller with your hand as you could be burnt.
Please avoid installing near the following places;
Gas stove, Ventilator or Air conditioner due the higher temperature or higher humidity
Do not place any materials on the laminator as they could catch a fire
Avoid the direct sunlight for the installing the machine
Make sure no vibration and dusts are found in the place during the installation.
Avoid the dark and slope place for installation
Do not place any materials on the laminator as they could catch a fire
Do not touch the film and laminating machine just after lamination finishes as you could be burnt.
Use the machine with laminating purpose only.
Tidy up the place near the laminating machine.
CAUTION
P
O
W
E
R
I
N
S
T
A
L
L
A
T
I
O
N
5/48
SAFETY DEVICE
☞ Emergency Stop Switch (E-STOP S/W)
When emergency situation happened, it stops the running motor(rollers) rotation and system operation.
In case of emergency, use this switch.
☞ Position of E-Stop Switch ☞ How to use
Press the Red button to operate the Emergency Stop Switch.
All system is stopped when this is pressed.
Turn the switch to the right to release from Emergency Status.
Emergency Stop Switch
E-STOP S/W
6/48
WARNING STICKERS
For the user safety, in the outer design, the below sticker is attached. Be cautious not to injured during operation.
☞Roller caution ☞Higher Temperature
Do not touch the roller and heating plate with your hand as you could be burnt. Do not touch on the heating part
Roller's higher temperature and press can damage your body
☞Chain Caution
Do not your body wound into a chain.
You can suffer an injury
☞Electricity Caution
Inside the machine, high voltage flows,
Do not open the outer case
You can suffer injury or sudden death with electricity shock
Warning Stickers
7/48
WARNING STICKERS
Warning Stickers
8/48
PACKING CONTENTS
ITEMS Q'TY(EA)
LAMINATOR 1
FEED TABLE 1
FEED TABLE GUIDE 2
AIR COMPRESSOR 1
AIR HOSE 1
GLASS TUBE FUSE (20mm) 250V/5.0A 2
GLASS TUBE FUSE (20mm) 250V/6.3A 2
5mm LWRENCH 1
USER MANUAL 1
SLEEKING IDLE ROLLER 1
`
Packing Contents
QTOPIC-380
9/48
MAIN DEVICES
Main Devices
E-Stop S/W
Film Tension
Adjustment Knob
Rewinder Tension
Adjustment Knob
Roller Pressure
Adjustment Device
Control
Perforator(Optional)
Decurling
Adjustment Knob
Feeding Table
Film Shaft
Extension Feeding
Table(Optional)
Tray Paper
Bursting Roller
Power S/W
Feeding Gate
Paper Guide
Roller Safety Cover
Air Compressor
Rewinder
10/48
Inhaltsverzeichnis
Andere GMP Laminiergerät Handbücher
GMP
GMP PROTOPIC AUTO-540 HS Bedienungsanleitung
GMP
GMP PROTOPIC III-540 Bedienungsanleitung
GMP
GMP ELECTRO ULTRA LAMITRIM-1800 Bedienungsanleitung
GMP
GMP EXCELAM-1100SWING Bedienungsanleitung
GMP
GMP RTR-380COMBI Bedienungsanleitung
GMP
GMP GraphicMaster 1600HR Bedienungsanleitung
GMP
GMP SURELAM-PRO540HR Bedienungsanleitung
GMP
GMP PROTOPIC AUTO-540 HS Bedienungsanleitung
GMP
GMP SURELAM-PRO540HR Bedienungsanleitung
GMP
GMP PROTOPIC-540 QUATRO SLIT Bedienungsanleitung
