GO Networks WLP Kurzanleitung

Document #: WLP22070601-R1

GO Metro Broadband Wireless

Getting Started

Technical Guide for WLP

Wireless LAN Pico Base Station

Version 2.2

GO WLP Getting Started Guide

Trademarks and Licensing Agreement

All information contained in this document is protected by international

express written consent of GO Networks Inc.

GO Metro Broadband Wireless, Go MBW, WLAN Sector Base Station, WLS, GO

WLAN Pico Base Station, WLP, GO Wireless Network Controller, and WNC are all

trademarks of GO Networks Inc.

Any duplication, transmission by any method, or storage in an information

retrieval system of any part of this publication for other purposes other than

those stated above is strictly prohibited without the specific written permission

of GO Networks, Inc. This includes, but is not limited to, transcription into any

form of computer system for audio, text, print, or visual retrieval. All rights

under federal copyright laws and international laws will be strictly enforced.

All other trademarks and registered trademarks are the property of their

respective owners.

GO Networks Inc.

1943 Landings Drive •Mountain View, CA 94043 •USA

Tel +1.650.962.2000 •Fax +1.650.962.2010

Email [email protected]

Version 1.00

- Page 1 of 31-

FCC Compliance Status

The following information is for FCC compliance:

This device complies with Part 15 of the FCC Rules. Operation is subject to

the following conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including

interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits of a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

when the equipment is operated in a residential environment, this

equipment generates, uses, and radiates radio frequency energy, and if

not installed and used in accordance with the instructions, may cause

harmful interference. However, there is no guarantee that interference will

not occur.

To meet regulatory restrictions, the outdoor access point must be

professionally installed.

The Part 15 radio device operates on a non-interference basis with other

devices operating at this frequency when using its antennas. Any changes

or modifications not expressly approved by GO Networks could void the

user's authority to operate the equipment.

The antennas used for this transmitter must not be co-located or operating

in conjunction with any other antenna or transmitter.

- Page 2 of 31-

Table of Contents

Introduction ........................................................................................................................................3

Key Product Features ............................................................................................................................3

Organization..............................................................................................................................................4

GO WLAN Pico Base Station (WLP)..................................................................................................5

WLP Package Components.........................................................................................................................5

WLP Safety Information...............................................................................................................................5

RF Exposure..............................................................................................Error! Bookmark not defined.

WLP Lightning Protector............................................................................................................................6

Installation..........................................................................................................................................7

Installation Process......................................................................................................................................7

Site Survey................................................................................................................................................7

Assembling and Mounting...........................................................................................................................8

Mounting the Antenna................................................................................................................................11

Cable Connections.....................................................................................................................................11

Grounding Cable......................................................................................................................................13

Ethernet Connection................................................................................................................................13

Power Connection ...................................................................................................................................13

Console Connection ................................................................................................................................13

Hardware and Connectors Installation Tools...........................................................................................13

Power Up and Software Configuration.....................................................................................................14

Post-installation Testing Procedure.........................................................................................................14

Configuring the WLP........................................................................................................................15

Connect and Access the WLP.................................................................................................................15

Configuring the Management Connectivity..............................................................................................17

Configuring the Radio Settings................................................................................................................17

Setting the Radio Data Rates..................................................................................................................17

Configuring Multiple SSIDs......................................................................................................................18

Enabling the Radio Interface....................................................................................................................19

Configuring the WDS...............................................................................................................................19

Configuring Authentication Types............................................................................................................22

Configuring the Radius Client in the WLP................................................................................................22

Configuring Privacy Methods...................................................................................................................23

Saving the Configuration..........................................................................................................................24

WLP Configuration Example....................................................................................................................24

Upgrading the WLP Software..........................................................................................................25

Appendix A: List of Acronyms........................................................................................................27

Appendix B: Wiring Specifications.................................................................................................29

- Page 3 of 31-

Introduction

GO Networks’ WLP device is the key enabler for the Metro Broadband

Wireless (MBW) Solution. Go Pico Cellular WiFi architecture offers a novel

topology for metro WiFi networks which relies on the strengths of

innovative XRF™ architectures. This architecture provides the coverage,

capacity, and scalability required to deliver next-generation services and

overcome the limitations of existing metro WiFi solutions.

The Go Networks’ Pico Cellular WiFi architecture is a highly scalable

Micro/Pico topology which provides unprecedented flexibility to service

providers deploying Metro WiFi networks.

Key Product Features

a. Robust Pico cellular WiFi solution

b. Separate accesses & backhaul radios delivering unmatched

bandwidth

c. xRF™ smart antenna engine for unmatched (360o) coverage and

capacity enhancements

d. Advanced automatic mesh

e. Designed for streetlight, wall, or pole deployment

- Page 4 of 31-

Organization

The GO Metro Broadband Getting Started Guide for the Wireless LAN Pico

Base Station (WLP) offers information and instructions for quickly installing

and configuring the WLP. The instructions and information are presented in

one volume as follows:

Introduction

Contains introductory information about the WLP.

GO WLAN Pico Base Station

Presents a general description and overview of

the WLP including content and safety procedures.

Installation Process

Describes the installation process for the WLP.

WLP Component and Cable

Connections

Describes the WLP component and cable

connections.

Configuring the WLP

Describes how to configure the WLP.

Upgrading the WLP Software

Explains how to update the WLP software.

Appendix A

Lists the acronyms that appear in the manual.

Appendix B

Details the wiring specifications.

- Page 5 of 31-

GO WLAN Pico Base Station (WLP)

The GO WLAN Pico Base Station (WLP) complements the WLAN Sector

Base Station (WLS) by delivering street-level coverage and providing

capacity enhancements in dense metro areas over a single 802.11b/g

channel, while backhauling traffic over multiple 802.11a/b/g radios.

The WLP Base Station delivers omni-directional (360o) coverage while

retaining full xRF smart antenna engine functionality for enhanced capacity

and range.

WLP Package Components

The WLP package items are listed in Table 1:

DESCRIPTION REV QTY

Wall/Poll Mount Kit Assembly (new) 1.0 1

Connectors Kit for WLP Package 1.0 1

WLP unit 1.0 1

WLP Access Antenna 2.4GHz 7.4dBi Gain,

Omni 4

802.11a 10dBi Omni Antenna (Backhaul) 2

Streetlight Power Tap Adapter 1

Table 1: WLP package contents

Deployments of gateway devices connected by wire to an indoor

switch/router would include installation of a lightning protector. A lightning

protector is not supplied as part of the standard package. It can be

ordered from GO Networks as an accessory.

Specific installation may require different Power/Ethernet connections. See

WLP Component and Cable Connections for more details.

- Page 6 of 31-

WLP Safety Information

RF Exposure

The WLP, an outdoor access point, is compliant with the requirements

set forth in CFR 47 section 1.1307, addressing RF Exposure from radio

frequency devices as defined in OET Bulletin 65. The outdoor access

point antennas should be installed to provide a separation distance of at

least 3 feet (1 meter) from humans

WLP Lightning Protector

A lightning protector is required when the WLP unit is installed in an

outdoor location and the Ethernet cable connects to an indoor network

device. The purpose of the lightning protection is to protect people and

equipment located indoors from lightning that might strike the WLP or its

outdoor cables. Therefore, the lightning protector device should be

installed indoors, as close as possible to the point where the cables enter

the building.

The lightning protector can also be installed outdoors, as long as the

cables that go from the lightning protector to the indoors are well

protected from lightning between the box and the building entrance.

Verify that you have shared grounding. GO Networks offers a lightning

protector that can be ordered separately.

- Page 7 of 31-

Installation

Installation Process

Installing the WLAN Pico Base Station involves the following steps:

1. Performing a Site Survey

2. Assembling and Mounting

3. Mounting the WLP unit

4. Connecting the Antennas

5. Connecting the cables

6. Powering up the unit and configuring the software

7. Performing a Post-installation Testing Procedure to verify

connectivity and operation

Site Survey

Most wireless LANs include many access points installed in various

locations in an overlapping radio-cell pattern. It is important to carefully

position each access point’s positioning and the assignment of its radio

channels. Therefore, a site survey becomes an essential first step before

physically deploying the GO MBW WLP Pico Cellular Base Station solution.

Installation of the access points requires a backhaul to interface the

corporate network or Internet. This backhaul connection can be a mesh

configuration, an Ethernet-wired connection, or a third-party solution.

When using any method other then a wired connection, keep in mind the

WLP has to have a good reception on its BH side so it will not limit the

access-channel performance.

Conclude the site survey with a detailed plan of the MBW system

deployment. The system deployment plan should include WLP mounting

points and the routes for the power and backhaul cables.

Note: When mounting the WLP on a pole (or wall mount), the pole

should be able to support four times the weight of the WLP, as

well as the wind loading created by the WLP.

Since the mounting structure itself is a potential source of

interference, the cell should be mounted with at least 4 feet of

clearance between the antennas and the mounting structure.

- Page 8 of 31-

Assembling and Mounting

The universal mount is used to attach and secure the WLP to a wall, a

lamppost, or a variety of poles.

The WLP mounting consists of the following stages:

a. Securing the mounting brackets to a wall, lamp post, or pole.

b. Connecting the WLP unit to the brackets using the ‘L’ adaptor.

c. Aligning the WLP unit.

Table 2 lists the universal mount parts:

Item

No. Description Qty Picture

A Wall/poll bracket 1

B Clamping bracket 1

C WLP ‘L’ adapter wall/poll

mount 1

D Bolt M8x70 2

E Screw Hex Cap M8 x25 1

F Bolt M8x40 1

G Washer flat M8 3

H Washer spring M8 4

I Nut M8 1

Inhaltsverzeichnis

Andere GO Networks Drahtloser Zugangspunkt Handbücher

GO Networks

GO Networks MBW 510 Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung