Go Rhino Dominator d2 series Bedienungsanleitung

QTY PARTS DESCRIPTION

5/16” U-NUTS

6 5/16” X1” HEX BOLTS

6 5/16” LOCK WASHERS

5/16” FLAT WASHERS

18 3/8” x 1 “ HEX BOLTS

3/8” LOCK WASHERS

QTY PARTS DESCRIPTION

3/8” FLAT WASHERS

18 3/8” HEX NUTS

3 C07P PASSENGER MOUNTING BRACKETS

C07D DRIVER MOUNTING BRACKETS

1 D24041P PASSENGER SIDESTEP

D24041D DRIVER SIDESTEP

INSTALLATION INSTRUCTIONS

STEP 1. Read the instructions completely before you begin the installation.

If the vehicle isequipped with factory running boards, remove the fasteners and running boards.

DOMINATOR 2 SERIES SIDESTEPS

ASSEMBLY & INSTALLATION INSTRUCTIONS FOR

PART NO. D24041

07-12 CHEVY/GMC 1500 EXTENDED CAB PICKUP 2/4WD

07-10 CHVEY/GMC 2500HD, 3500 4DR EXTENDED CAB 2/4WD

11-12 CHEVY/GMC 2500HD, 3500HD 4DR EXTENDED CAB P/U 2/4WD (Gasoline only)

STEP 2. This installation uses three mounting brackets per side. Begin by installing the passenger side

front mounting bracket. Measure reward from the front fender bolt approximately 14” and Locate the

single hole in the body pinch mold and the two holes in the rocker panel.

STEP 3. Remove the plastic plug from the rocker panel and install (1) 5/16” U-NUT as shown.

PLASTIC PLUG

3/8” X 1” HEX BOLT, FLAT WASHER, LOCK WASHER & HEX NUT

5/16” X 1” HEX BOLT, LOCK WASHER & FLAT WASHER

INSTALLED 5/16” U-NUT

BRACKET MOUNTING POINTS

C07P MOUNTING BRACKET

PINCH MOLD

ROCKER PANEL

STEP 4. Loosely attach one of the C07P mounting brackets to the rocker panel and pinch mold using the

5/16” and 3/8” fasteners as shown.

STEP 5. Locate the holes in the body for the center and rear mounting brackets. Measure rearward from

the front fender bolt 37 ¾” for the center and 67” for the rear bracket. Repeat steps 3 & 4 to install the

center and rear brackets.

STEP 6. Position D24041P passenger sidestep up to the vehicle and loosely attach it to the mounting

brackets using the 3/8” x 1” hex bolts, flat washers, lock washers and hex nuts.

D24041P SIDESTEP

PASSENGER SIDE FRONT

C07P MOUNTING BRACKETS

C07P MOUNTING BRACKET

3/8” X 1” HEX BOLTS, FLAT WASHERS, LOCK WASHERS & HEX NUTS

STEP 7. Tighten all mounting bracket and sidestep nuts and bolts.

STEP 8. Repeat the above steps to install the driver side mounting brackets and sidestep.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Go Rhino Autoteile Handbücher

Go Rhino

Go Rhino DOMINATOR II Series Bedienungsanleitung

Go Rhino

Go Rhino DOMINATOR 2 SERIES Programmierhandbuch

Go Rhino

Go Rhino Dominator 2 series Bedienungsanleitung

Go Rhino

Go Rhino DOMINATOR II Series Bedienungsanleitung

Go Rhino

Go Rhino DOMINATOR II Series Bedienungsanleitung

Go Rhino

Go Rhino DOMINATOR SERIES Programmierhandbuch

Go Rhino

Go Rhino DOMINATOR 2 SERIES Programmierhandbuch

Go Rhino

Go Rhino dominator 2 series Bedienungsanleitung

Go Rhino

Go Rhino DOMINATOR D2 SERIES Bedienungsanleitung

Beliebte Autoteile Handbücher anderer Marken

Hellwig

Hellwig 5812 Bedienungsanleitung

Boomba Racing

Boomba Racing EVO X Bedienungsanleitung

Xtracer

Xtracer 1152 Bedienungsanleitung

Tuff Country

Tuff Country 32103 Bedienungsanleitung

ADD

ADD 2003 – Current Chevy 1500/2500 ADD Lite Bedienungsanleitung

ADD

ADD 2007-2014 Jeep JK venom Bedienungsanleitung

Gibson

Gibson 69522 Bedienungsanleitung

Airaid

Airaid 400-279 Bedienungsanleitung

Poison Spyder

Poison Spyder JK BRAWLER ROCKERS Service-Handbuch

ADD

ADD 2007-2013 GMC 1500 Bedienungsanleitung

aFe Power

aFe Power 54-12208 Bedienungsanleitung

USA Standard Gear

USA Standard Gear Spartan Locker Bedienungsanleitung

Fabtech

Fabtech FTS26016BK Bedienungsanleitung

Torklift

Torklift C2207/FMTPJ07LDCHSB Bedienungsanleitung

Grammer

Grammer COMPACTO Comfort S Bedienungsanleitung

RANCHO

RANCHO RS66505B Bedienungsanleitung

Renault

Renault ESPACE 82 01 440 136 Bedienungsanleitung

Chassisworks

Chassisworks gStreet 5817-F10-12 Bedienungsanleitung

Go Rhino dominator d2 series Bedienungsanleitung

Beliebte Autoteile Handbücher anderer Marken