Gplink GWD050 Bedienungsanleitung

Power Generation

Installation Guide

www.gplink.com

Satellite Tracking and Monitoring Solutions

Contact gplink at +1.252.504.5113 at least 24 hours

prior to scheduled installation for activation of units.

(48 hours on weekends)

2Power Generation Installation Guide Version 2.0.0 - July 2016

Contents

1. Introduction and Purpose 3

2. Installation & Components 4

2.1 Installation 4

2.2 Power Harness 4

2.3 J1939 Harness 5

2.4 MODBUS Harness 5

2.5 Analog Inputs and Outputs 6

3. 2-Inch User Interface 7

3.1 Operation 7

3.2 Diagnostics

4. gplink Concierge & Technical Support 11

4.1 Transferable Limited Warranty 11

3Power Generation Installation Guide Version 2.0.0 - July 2016

1. Introduction and Purpose

Notice - The gplink system is only an aid to operation of the equipment it is installed on. The performance

of the system and the system performance specications can be affected by many factors including but

not limited to equipment failure, environmental conditions, improper installation, handling and/or use.

This device should not be used for any navigational or safety purpose. The gplink system is used at your

sole risk and in no event shall gplink, Inc. be held liable for any costs, losses, liabilities, damages, expense

or claims of any nature incurred or sustained in respect of this device or its use. You further indemnify and

hold harmless gplink Inc. and their partners from any liability or loss resulting from use of the device.

Parts List (Single Band)

Part # DESCRIPTION QTY.

AN9003

AN9004

GPS/GSM antenna

GPS/Iridium antenna 1

GWD050

GWD051

GPLink (MTU) GSM

GPLink (MTU) Iridium 1

HN9040 Power Harness 1

HN9044 J1939 CAN Harness 1

HN0671 Antenna Extension 2

HW0245 Mounting Hardware 1

BK9990 Antenna Mounting bracket 1

WI0020 Installation Manual 1

Contact gplink at +1.252.504.5113 at least 24 hours (48 on weekends)

prior to scheduled installation for activation of units.

HN9042

GWD050 - GSM GWD051 - Iridium BK9990

HN9041HN9040

4Power Generation Installation Guide Version 2.0.0 - July 2016

2. Installation & Components

2.1 Installation

Locate an area to mount the antenna less than 3 meters from the Mobile Transmitting Unit (MTU). Mount the

antenna, using the Antenna mounting bracket (BK9990), and run the cables to MTU.

a) Mount the MTU in an area where there is easy access to antenna cables and the battery or power source.

b) GPS Connect the Blue colored wire to the J1 connector on the MTU.

c) GSM Connect the Yellow colored wire to the J2 connector on the MTU if connecting a GMS device.

SAT Connect the White colored wire to the J3 connector on the MTU if connecting an Iridium device

Connect cables to mounting location of the MTU.

2.2 Power Harness

(HN9040) (See the Wiring Diagram)

a) Connect the power harness (HN9040) (Gray Connector (A)) to the MTU at receptacle “A”

b) Connect the RED wire directly to a continuous 12-24 vDC source or the positive battery terminal.

c) Connect the BLACK wire to a good ground, preferably the negative battery terminal.

Note:The connector and receptacle are keyed so that they can only go together one way. Please be sure to line up the

guides on the connector with the slots in the receptacle when connecting the harness to the MTU.

J1 J2

4-pin

Deutsche

connector

5Power Generation Installation Guide Version 2.0.0 - July 2016

2.3 J1939 Harness

(HN9041) (See the Wiring Diagram)

a) Connect the J1939 harness (HN9041) (Black Connector (B)) to the MTU at receptacle “B”.

b) Connect the GREEN (CAN High),YELLOW (CAN Low) and BARE (Shield) wires to the corresponding J1939

connector wires on the generator.

c) The BLUE and GRAY wires are available for use as outputs.

2.4 MODBUS Harness

(HN9042) (See the Wiring Diagram)

a) Connect the four pin Deutsche connector to the Deutsche connector on the Power harness (HN9040).

b) Connect the WHITE (D+), GREEN (D-) and BLACK (Ground) wires to the corresponding connector on the

Genset controller.

J1939 B

Genset

Controller

4-Pin

Deutsche

connector

6Power Generation Installation Guide Version 2.0.0 - July 2016

2.5 Analog Inputs and Outputs

a) From the Power harness (HN9040) connect the BROWN wire to any 240/33 fuel level sender input.

b) Other Inputs and Output connection are available.

Wiring diagram

Figure 1

BLACK

Ground

BROWN

Fuel

ORANGE

Switched IN

Shield

Output

CAN (low)

CAN (high)

RED

BLUE

BARE

YELLOW

GREEN

Main

Battery

J1/GPS - Blue wire to Antenna

HN9040

HN9042

HN9041

Serial # KWD304-VMS000 FPN:KTW304

PASS 02-28-09

SIM CARD

IRIDIUM MODEM #

FCC ID:PY76220511

Not used - 1

Not used - 4

Not used - 5

Not used - 6

Output - BLUE - 2

Output - GRAY - 3

12 - Not used

11 - Not used

10 - Not used

8 - Not used

9 - BLACK

10 - RED

11 - WHITE

12 - GREEN

7 - BLACK - Ground

PURPLE - 1

Switched IN - ORANGE - 2

Fuel - BROWN - 3

Not used - 4

RED/WHITE - 5

RED - 6

9 - YELLOW - CAN(High)

8 - BARE - Shield

7 - GREEN - CAN (Low)

J3/SAT - White wire to Antenna - GWD051

J2/GSM - Yellow wire to Antenna - GWD050

(B) Black

connector

(A) Gray

connector

J1939 Cable

J1939

FARIA BUS

GRAY

BLACK

GREEN WHITE

+ 12-24 vDC -

+12-24vDC

User Interface

(optional)

WHITE - D(+)

BLACK - Ground

GREEN - D(-)

GWD050/GWD051

7Power Generation Installation Guide Version 2.0.0 - July 2016

3. 2-Inch User Interface (Optional)

The 2-inch User Interface displays the status of communications to the MTU, (mobile transmitting unit).The MTU uses

GPS and at least one communication channel, (either GSM/GPRS or Iridium satellite) to send vehicle or equipment status

and position.

Connect the User Interface with the wiring harness (HN9040) as shown in the Wiring Diagram.

3.1 Operation

When power is applied your interface display will beep and the LCD will illuminate.To show that the MTU is running the

2-inch display will show one of the following messages:

1. “Wait” is the boot up message, which indicates the unit is trying to communicate with the MTU.

2. “Comm” Indicates the MTU is running, has a GPS x and has at least one communication channel open/available,

(GSM or Iridium).

8Power Generation Installation Guide Version 2.0.0 - July 2016

3.“No-Comm” with RED LED’s continuously on indicates the MTU is running but cannot get a GPS x, cannot communicate,

(via GSM or Iridium), or both GPS and communication links are down.

3.2 Diagnostics

Press the “S” button to enter the STATUS mode.Then, press “Mode” to step through status displays as follows:

For dual band system, (GSM and Satellite), GSM signal strength will display from 0, (no signal) to 5, (best signal).

9Power Generation Installation Guide Version 2.0.0 - July 2016

Sat signal strength, will display from 0, (no signal), to 5, (best signal).

GPS PDOP X 100, (a PDOP of 1.23 will read 0123,etc),9999 (means no GPS signal), For PDOP lower numbers represent

a better connection.

Main battery voltage X100 (battery voltage of 12.34Volts will appear as “1234”).

10Power Generation Installation Guide Version 2.0.0 - July 2016

Back up Battery voltage The Back-Up voltage will be the same value as the main battery voltage. The wires are tied

together in the harness.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere gplink GPS Handbücher

gplink

gplink J1939 Bedienungsanleitung

Beliebte GPS Handbücher anderer Marken

Raven

Raven Cruizer II Handbuch

Hama

Hama 53118 Bedienungsanleitung

Garmin

Garmin SOUNDER 125 Bedienungsanleitung

Garmin

Garmin DEZL 580 Bedienungsanleitung

Jigabot

Jigabot EX Bedienungsanleitung

Pointer

Pointer Cellocator CelloTrack XT LTE Installationsanleitung

Queclink

Queclink GV55LITE Bedienungsanleitung

Voxson

Voxson Voxtrack GPS500 Gebrauchsanweisung

Garmin

Garmin ECHOMAP PLUS Bedienungsanleitung

Starcom Systems

Starcom Systems Kylos Compact Bedienungsanleitung

Garmin

Garmin 15 H Series Bedienungsanleitung

Cobra

Cobra Marine MC 600Ci Bedienungsanleitung

Cellocator

Cellocator CelloTrack T Bedienungsanleitung

Enfora

Enfora Mini-MT GSM2228UG001 Bedienungsanleitung

Magellan

Magellan eXplorist 100 Bedienungsanleitung

LTE

LTE G50B Bedienungsanleitung

Garmin

Garmin DEZL OTR500 Bedienungsanleitung

SkyGolf

SkyGolf SkyCaddie SG1 Bedienungsanleitung

gplink GWD050 Bedienungsanleitung

Beliebte GPS Handbücher anderer Marken