Graco XM PFP Bedienungsanleitung

332073C

Instructions-Parts

XM™PFP

Hot Water Flush Kit

For flushing the XM PFP system with hot water. For professional use only.

100 psi (0.7 MPa, 7 bar) Maximum Inlet Water Pressure to Float Valve

180°F (82°C) Maximum Outlet Fluid Temperature

See Models, page 2 for more information.

Important Safety Instructions

Read all warnings and instructions in this manual and

the XM PFP Operation manual. Save all instructions.

WLD

Get other manuals https://www.bkmanuals.com

Related Manuals

2332073C

Contents

Related Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Component Identification . . . . . . . . . . . . . . . . . . . . 3

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Connect Air Supply . . . . . . . . . . . . . . . . . . . . . . . . . 6

Connect Water Supply . . . . . . . . . . . . . . . . . . . . . . 6

Priming the Heater . . . . . . . . . . . . . . . . . . . . . . . . . 7

Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Graco Standard Warranty . . . . . . . . . . . . . . . . . . . 12

Related Manuals

Models

Manual Description

3A2776 XM PFP Operation

3A2989 XM PFP Repair-Parts

308652 Husky

™

205 Air-Operated Diaphragm

Pumps, Instructions-Parts

309524 Viscon

HP Heater, Instructions-Parts

Part No. Description

24X113 Hazardous Location Hot Water Flush Kit

24Y132 Non Hazardous Location Hot Water Flush Kit

Get other manuals https://www.bkmanuals.com

Warnings

332073C 3

Warnings

The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama-

tion point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When

these symbols appear in the body of this manual or on warning labels, refer back to these Warnings. Product-specific

hazard symbols and warnings not covered in this section may appear throughout the body of this manual where

applicable.

FIRE AND EXPLOSION HAZARD

Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. Paint or solvent

flowing through the equipment can cause static sparking. To help prevent fire and explosion:

• Use equipment only in well ventilated area.

• Eliminate all ignition sources; such as pilot lights, cigarettes, portable electric lamps, and plastic drop

cloths (potential static sparking).

• Ground all equipment in the work area. See Grounding instructions.

• Never spray or flush solvent at high pressure.

• Keep work area free of debris, including solvent, rags and gasoline.

• Do not plug or unplug power cords, or turn power or light switches on or off when flammable fumes

are present.

• Use only grounded hoses.

• Hold gun firmly to side of grounded pail when triggering into pail. Do not use pail liners unless they are

anti-static or conductive.

•Stop operation immediately if static sparking occurs or you feel a shock.Do not use equipment until

you identify and correct the problem.

• Keep a working fire extinguisher in the work area.

ELECTRIC SHOCK HAZARD

This equipment must be grounded. Improper grounding, setup, or usage of the system can cause

electric shock.

• Turn off and disconnect power at main switch before disconnecting any cables and before servicing

or installing equipment.

• Connect only to grounded power source.

• All electrical wiring must be done by a qualified electrician and comply with all local codes and

regulations.

SKIN INJECTION HAZARD

High-pressure fluid from gun, hose leaks, or ruptured components will pierce skin. This may look like just

a cut, but it is a serious injury that can result in amputation. Get immediate surgical treatment.

• Do not spray without tip guard and trigger guard installed.

• Engage trigger lock when not spraying.

• Do not point gun at anyone or at any part of the body.

• Do not put your hand over the spray tip.

• Do not stop or deflect leaks with your hand, body, glove, or rag.

•FollowthePressure Relief Procedure when you stop spraying and before cleaning, checking, or

servicing equipment.

• Tighten all fluid connections before operating the equipment.

• Check hoses and couplings daily. Replace worn or damaged parts immediately.

Get other manuals https://www.bkmanuals.com

Warnings

4332073C

BURN HAZARD

Equipment surfaces and fluid that’s heated can become very hot during operation. To avoid severe

burns:

• Do not touch hot fluid or equipment.

EQUIPMENT MISUSE HAZARD

Misuse can cause death or serious injury.

• Do not operate the unit when fatigued or under the influence of drugs or alcohol.

• Do not exceed the maximum working pressure or temperature rating of the lowest rated system

component. See Technical Data in all equipment manuals.

• Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all

equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete information

about your material, request Safety Data Sheet (SDS) from distributor or retailer.

• Do not leave the work area while equipment is energized or under pressure.

• Turn off all equipment and follow the Pressure Relief Procedure when equipment is not in use.

• Check equipment daily. Repair or replace worn or damaged parts immediately with genuine manu-

facturer’s replacement parts only.

• Do not alter or modify equipment. Alterations or modifications may void agency approvals and create

safety hazards.

• Make sure all equipment is rated and approved for the environment in which you are using it.

• Use equipment only for its intended purpose. Call your distributor for information.

• Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.

• Do not kink or over bend hoses or use hoses to pull equipment.

• Keep children and animals away from work area.

• Comply with all applicable safety regulations.

PERSONAL PROTECTIVE EQUIPMENT

Wear appropriate protective equipment when in the work area to help prevent serious injury, including

eye injury, hearing loss, inhalation of toxic fumes, and burns. This protective equipment includes but is

not limited to:

• Protective eyewear, and hearing protection.

• Respirators, protective clothing, and gloves as recommended by the fluid and solvent manufacturer

Get other manuals https://www.bkmanuals.com

Component Identification

332073C 5

Component Identification

. 1

WLE

)

(

Key:

A 3/4 NFR Garden Hose Inlet

BHeater

CPump

D Hot Water Outlet to Flush

Pump

ETank

F Suction Hose (see

installation)

GAirHose

. 2: Heater Power Cable

WLE

WLD

Hazardous Location XM PFP Non-Hazardous Location XM PFP

Get other manuals https://www.bkmanuals.com

Installation

6332073C

Installation

Optional Location 1

See F

. 1 on page 5 and F

. 3.

1. Use four bolts (4) to install the bracket (2) onto the

system frame.

2. Use four bolts and nuts (4, 5) to install tank (1) onto

bracket (2).

3. Follow Connect Air Supply, page 8. Connect air

hose (8) to circulation pump (53) and diaphragm

pump (P) on the PFP system.

4. Connect suction hose (F) to the flush pump and

insert in the hot water flush tank.

5. Connect heater power cable.

a. Model 24Y132: With the heater ON/OFF toggle

switch (H) OFF, connect power cable to the

corded receptacle hanging below the junction

box on the XM PFP sprayer.

b. Model 24X113: With the heater ON/OFF toggle

switch (H) OFF, route the heater power cable

through the Flush Heater cord grip. See F

. 2,

page 5. See system manual for power connec-

tion.

The equipment must be grounded to reduce the risk

of static sparking and electric shock. Electric or static

sparking can cause fumes to ignite or explode.

Improper grounding can cause electric shock.

Grounding provides an escape wire for the electric

current.

. 3: Optional Location 1

WLE





)









)

Get other manuals https://www.bkmanuals.com

Installation

332073C 7

Optional Location 2

See F

. 1 on page 5 and F

. 4 on page 7.

1. Use four bolts (4) to connect the three bracket

pieces (2, 6, 7).

2. Use four bolts (4 to install the bracket assembly (2)

onto system frame.

3. Use four bolts and nuts (4, 5) to install tank (1) onto

bracket assembly (2).

4. Follow Connect Air Supply, page 8.

5. Connect suction hose (F) to the flush pump and

insert in the hot water flush tank.

6. Connect heater power cable.

a. Model 24Y132: Connect With the heater

ON/OFF toggle switch (H) OFF, connect power

cable to the corded receptacle hanging below

the junction box on the XM PFP sprayer.

b. Model 24X113: With the heater ON/OFF toggle

switch (H) OFF, route the heater power cable

through the Flush Heater cord grip. See F

. 2,

page 5. See system manual for power connec-

tion.

. 4: Optional Location 2

)









)











WLE



Get other manuals https://www.bkmanuals.com

Connect Air Supply

8332073C

Connect Air Supply

1. Disconnect air supply (AS) from Heated Fluid Circu-

lation Pump (P) for hose bundle.

2. For Model 24Y132: install the tee (9), nipple (10).

The cap (11) is not used.

3. For Model 24X113:

a. Remove cap (11).

4. Connect air hose (8) to circulation pump (53) and

diaphragm pump (P) on the PFP system. See F

. 3

on page 6 or F

. 4 on page 7.

5. Connect the air hose (8) to the nipple fitting (10).

See #2 in F

. 5. Connect the air hose (8) to the hot

water circulation pump (53).

Connect Water Supply

1. Connect garden hose to a water supply and the

water inlet (A). See F

. 1, page 5.

. 5:

WLD

 







P P

. 6:

WLD

Get other manuals https://www.bkmanuals.com

Priming the Heater

332073C 9

Priming the Heater

1. Turn on water supply.

2. Loosen needle valve on diaphragm pump to pump

water through the heater.

3. Turn the heated water flush switch on the XM PFP

sprayer to the ON position. The switch is located

next to the main power switch above the dosing

valves.

4. Use the dial on the heater to set desired tempera-

ture. See table.

5. Turn on XM PFP flush pump ON to begin running

water through the pump.

6. Spray until the water is dispensed from the gun.

7. Continue flushing as necessary.

Equipment surfaces and fluid that is heated can

become very hot during operation. To avoid burns and

fire and explosions:

• Do not touch hot fluid or equipment.

• Only use water.

NOTICE

To prevent damaging the heater element, never

turn on the heater without it completely filled with

water.

NOTICE

To prevent damage to the diaphragm pump, never

turn the heater dial past 9.

Heater Dial Tank Temperature °F(°C)

9 180 (82)

8 160 (71)

7 140 (60)

6 120 (48)

5 100 (37)

Get other manuals https://www.bkmanuals.com

Parts

10 332073C

Parts

Hazardous Location Hot Water Flush Kit, 24X113

Non Hazardous Location Hot Water Flush Kit, 24Y132

WLF



































 



 







































NOTE: Use sealant on all pipe threads.

Get other manuals https://www.bkmanuals.com

Andere Handbücher für XM PFP

Inhaltsverzeichnis

Andere Graco Steuereinheit Handbücher

Graco

Graco Trabon MD Series Bedienungsanleitung

Graco

Graco E-Flo B Series Stücklistenhandbuch

Graco

Graco DynaMite 224906 Bedienungsanleitung

Graco

Graco 15X303 Technisches Referenzhandbuch

Graco

Graco CleanShot 287727 Bedienungsanleitung

Graco

Graco 2K Ultra-Lite Series Bedienungsanleitung

Graco

Graco 222-411 Datenblatt

Graco

Graco 202844 Evenflo Bedienungsanleitung

Graco

Graco PM5 238513 Bedienungsanleitung

Graco

Graco 239850 Bedienungsanleitung

Graco

Graco Therm-O-Flow 25C994 Bedienungsanleitung

Graco

Graco LDP5 Bedienungsanleitung

Graco

Graco Series E Bedienungsanleitung

Graco

Graco NXT011 Bedienungsanleitung

Graco

Graco Dispensit 710 Bedienungsanleitung

Graco

Graco 24P976 Bedienungsanleitung

Graco

Graco 205612 Bedienungsanleitung

Graco

Graco Control Architecture Module Betriebsanleitung

Graco

Graco Dyna-Star 24Y408 Gebrauchs- und Pflegehandbuch

Graco

Graco Gun Flush Box 570046 Bedienungsanleitung

Graco

Graco ProGuard+ Bedienungsanleitung

Graco

Graco PD44 Leitfaden

Graco

Graco SaniForce 25D009 Stücklistenhandbuch

Graco

Graco PD44 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung

Flyron

Flyron FN-BC04 Bedienungsanleitung