Graco SERIES F Bedienungsanleitung

HIGH PRESSURE

Back Pressure Regulator

For use in a high pressure spray circulating system to regulate back pressure to gun(s)

and maintain proper pressure for circulation. For professional use only.

Not approved for use in European explosive atmosphere locations.

CARBON STEEL REGULATORS

Part No. 206819, Series F

3000 psi (21 MPa, 207 bar) Maximum Working Pressure

1000–3000 psi (7–21 MPa, 70–207 bar) Regulated Fluid Pressure Range

Part No. 222405, Series B

3000 psi (21 MPa, 207 bar) Maximum Working Pressure

0–1000 psi (0–7 MPa, 0–70 bar) Regulated Fluid Pressure Range

STAINLESS STEEL REGULATOR

Part No. 238926, Series A

3000 psi (21 MPa, 207 bar) Maximum Working Pressure

1000–3000 psi (7–21 MPa, 70–207 bar) Regulated Fluid Pressure Range

Part No. 26A081, Acid Compatible

3000 psi (21 MPa, 207 bar) Maximum Working Pressure

1000–3000 psi (7–21 MPa, 70–207 bar) Regulated Fluid Pressure Range

Table of Contents

Symbols 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Warnings 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installation 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Operation 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Maintenance 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Parts 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Accessories 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Technical Data 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Warranty 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Graco Phone Number 12. . . . . . . . . . . . . . . . . . . . . . . . . .

Instructions–Parts List

306860S

06863

Important Safety Instructions

Read all warnings and instructions in this manual.

Save these instructions.

2 306860

Symbols

Warning Symbol

WARNING

This symbol alerts you to the possibility of serious

injury or death if you do not follow the instructions.

Caution Symbol

CAUTION

This symbol alerts you to the possibility of damage to

or destruction of equipment if you do not follow the

instructions.

WARNING

INSTRUCTIONS

EQUIPMENT MISUSE HAZARD

Equipment misuse can cause the equipment to rupture or malfunction and result in serious injury.

DThis equipment is for professional use only.

DRead all instruction manuals, tags, and labels before operating the equipment.

DUse the equipment only for its intended purpose. If you are not sure, call your Graco distributor.

DDo not alter or modify this equipment.

DCheck equipment daily. Repair or replace worn or damaged parts immediately.

DDo not exceed the maximum working pressure of the lowest rated system component. Refer to the

Technical Data on page 11 for the maximum working pressure of this equipment.

DUse fluids and solvents which are compatible with the equipment wetted parts. Refer to the Tech-

nical Data section of all equipment manuals. Read the fluid and solvent manufacturer’s warnings.

DRoute hoses away from traffic areas, sharp edges, moving parts, and hot surfaces. Do not expose

Graco hoses to temperatures above 180_F (82_C) or below –40_F (–40_C).

DWear hearing protection when operating this equipment.

DDo not lift pressurized equipment.

DComply with all applicable local, state, and national fire, electrical, and safety regulations.

306860 3

WARNING

INJECTION HAZARD

Spray from the gun, leaks or ruptured components can inject fluid into your body and cause extremely

serious injury, including the need for amputation. Fluid splashed in the eyes or on the skin can also

cause serious injury.

DFluid injected into the skin might look like just a cut, but it is a serious injury. Get immediate medi-

cal attention.

DDo not stop or deflect leaks with your hand, body, glove or rag.

DKeep your hands away from the end of the drain valve when opening it.

DLock the gun trigger safety when you stop spraying.

DFollow the Pressure Relief Procedure on page 7 if the spray tip clogs and before cleaning,

checking or servicing the equipment.

DFollow the Pressure Relief Procedure on page 7 before removing the regulator’s adjusting knob.

DDo not pressurize the system when the back pressure regulator’s adjusting knob is removed.

DTighten all fluid connections before operating the equipment.

DCheck the hoses, tubes, and couplings daily. Replace worn or damaged parts immediately.

Do not repair high pressure couplings; you must replace the entire hose.

DUse only Graco approved hoses. Do not remove the spring guard that is used to help protect the

hose from rupture caused by kinks or bends near the couplings.

TOXIC FLUID HAZARD

Hazardous fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin,

inhaled, or swallowed.

DKnow the specific hazards of the fluid you are using.

DStore hazardous fluid in an approved container. Dispose of hazardous fluid according to all local,

state and national guidelines.

DAlways wear protective eyewear, gloves, clothing and respirator as recommended by the fluid and

solvent manufacturer.

4 306860

Important Acid Catalyst Information

Regulator model 26A081 is designed for acid catalyst (”acid”) currently used in two–component, wood finishing

materials. Current acids in use (with pH levels as low as 1) are more corrosive than earlier acids. More corrosion–

resistant wetted materials of construction are required, and must be used without substitution, to withstand the

increased corrosive properties of these acids.

WARNING

Acid is flammable, and spraying or dispensing acid creates potentially harmful mists, vapors, and

atomized particulates. To help prevent fire and explosion and serious injury:

DRead and understand the fluid manufacturer’s warnings and Safety Data Sheet (SDS) to know

specific hazards and precautions related to the acid.

DUse only genuine, manufacturer’s recommended acid–compatible parts in the catalyst system

(hoses, fittings, etc.). A reaction may occur between any substituted parts and the acid.

DTo prevent inhalation of acid mists, vapors, and atomized particulates, everyone in the work area

must wear appropriate respiratory protection. Always wear a properly fitting respirator, which may

include a supplied–air respirator. Ventilate the work area according to instructions in the acid

manufacturer’s SDS.

DAvoid all skin contact with acid. Everyone in the work area must wear chemically impermeable

gloves, protective clothing, foot coverings, aprons, and face shields as recommended by the acid

manufacturer and local regulatory authority. Follow all fluid manufacturer recommendations, includ-

ing those regarding handling of contaminated clothing. Wash hands and face before eating or

drinking.

DRegularly inspect equipment for potential leaks and remove spills promptly and completely to avoid

direct contact or inhalation of the acid and its vapors.

DKeep acid away from heat, sparks, and open flames. Do not smoke in the work area. Eliminate all

ignition sources.

DStore acid in the original container in a cool, dry, and well–ventilated area away from direct sunlight

and away from other chemicals in accordance with acid manufacturer’s recommendation. To avoid

corrsion of containers, do not store acid in substitute containers. Reseal the original container to

prevent vapors from contaminating the storage space and surrounding facility.

Moisture Sensitivity of Acid Catalysts

Acid catalysts can be sensitive to atmospheric moisture and other contaminants.

Notice

Acid build–up will damage the seals and reduce the performance and life of the regulator. To prevent exposing

acid to moisture:

DAlways use a sealed container with a desiccant dryer in the vent, or a nitrogen atmosphere. Never store acids

in an open container.

DUse only moisture–proof hoses compatible with acids.

DAlways lubricate threaded parts with an appropriate lubricant when reassembling.

306860 5

Installation

The Typical Installations shown in Figs. 1 and 2 are

only guides in designing a system. For assistance in

designing a system to meet your needs, contact your

Graco distributor.

Installing the Back Pressure Regulator

1. Install the back pressure regulator (A) in the spray

gun return line (D). See Figs. 1 and 2.

2. Connect fluid lines to the 1/4 npt(f) inlet and outlets

of choice. Make sure the fluid flow agrees with the

IN and OUT markings on the regulator housing.

3. Install the accessory gauge, if used, in the optional

inlet.

4. If more than one spray station is used, install a

back pressure regulator (A) in the circulating line

(H) after the last spray station to maintain proper

system pressures. Refer to Fig. 2, for multiple

circulating spray stations.

NOTE: The two 1/4–20 tapped mounting holes on the

side of the regulator housing are for mounting the

regulator when flexible fluid lines are used.

6 306860

Installation

06865

KEY

A Back Pressure Regulator

B Air Filter/Regulator

C Fluid Supply Line

D Fluid Return Line

E Fluid Regulator

F Air-Assisted Airless Spray Gun

G Air Line

Fig. 1 SINGLE CIRCULATING SPRAY STATION

06866

Fig. 2 MULTIPLE CIRCULATING SPRAY STATION

KEY

A Back Pressure Regulator

B Air Filter/Regulator

C Fluid Supply Line

D Fluid Return Line

E Fluid Regulator

F Air-Assisted Airless Spray Gun

G Air Line

H Fluid Circulation Line

306860 7

Operation

Pressure Relief Procedure

WARNING

INJECTION HAZARD

The system pressure must be manually

relieved to prevent the system from

starting or spraying accidentally. Fluid

under high pressure can be injected through the

skin and cause serious injury. To reduce the risk of

an injury from injection, splashing fluid, or moving

parts, follow the Pressure Relief Procedure

whenever you:

Dare instructed to relieve the pressure,

Dstop spraying,

Dcheck or service any of the system equipment,

Dor install or clean the spray tip.

1. Lock the gun trigger safety.

2. Close the bleed-type master air valve (required in

your system).

3. Unlock the gun trigger safety.

4. Hold a metal part of the gun firmly to the side of a

grounded metal pail, and trigger the gun to relieve

pressure.

5. Lock the gun trigger safety.

6. Open the drain valve (required in your system),

having a container ready to catch the drainage.

7. Leave the drain valve open until you are ready to

spray again.

If you suspect that the spray tip or hose is completely

clogged, or that pressure has not been fully relieved

after following the steps above, very slowly loosen the

tip guard retaining nut or hose end coupling and relieve

pressure gradually, then loosen completely. Now clear

the tip or hose.

Adjusting the Regulator

The back pressure regulator controls pressure ahead

of the regulator intake.

To adjust the regulator, first, back the adjusting knob

out until there is no spring pressure. Then, turn the

knob clockwise to increase pressure.

Adjust the pump air pressure and the back pressure

regulator for the best spraying combination and proper

circulation of fluid.

Record the regulator and air pressure settings for

future reference. The regulator cylinder has exterior

markings (set points 1 to 8) for repeat settings.

8 306860

Maintenance

WARNING

COMPONENT RUPTURE HAZARD

To reduce the risk of serious bodily inju-

ry, including fluid injection or splashing in

the eyes or on the skin, always follow

the Pressure Relief Procedure on page 7 before

adjusting, cleaning, repairing, or removing the regu-

lator from the system.

Never pressurize the system with the back pres-

sure regulator adjusting knob removed.

Never completely remove the adjusting knob when

system pressure is present.

Flushing

Flush the regulator whenever the rest of the system is

flushed. Before flushing, open the regulator by turning

the adjusting knob counterclockwise until the spring

tension is relieved.

NOTE: Do not allow paint or solvent to set in the

system for a long time. Fluid could dry on the piston,

causing leakage at the piston packing. If leakage

occurs, disassemble and clean the regulator.

Cleaning

Regular cleaning and inspection, and lubrication of the

regulator are necessary to keep the regulator working

properly.

1. Open the regulator and follow the Pressure Relief

Procedure on page 7.

2. Remove the back pressure regulator from the

system.

3. Disassemble the regulator, referring to the parts

drawing on page 9. Clean and inspect all parts.

CAUTION

Use special care when handling the hard carbide

portions of the piston (13) and seat (12). Damage will

cause poor operation and leakage.

Repairing

Reference numbers marked with an asterisk (for

example, 3*) are included in the repair kits, which may

be purchased separately. For Models 206819 and

222405, order Repair Kit 220135. For Model 238926,

order Repair Kit 239000. For Model 26A081, order

Repair Kit 17M564. See page 9.

1. Lubricate the piston packing (9*), piston (13*), and

spring locater (10) with lithium base grease.

2. Place the washer (6) over the pointed end of the

piston (13*).

3. Place the packing (9*), with its lips facing down,

over the pointed end of the piston (13*) and

against the washer (6).

4. Insert the piston (13*) into the bottom of the cylin-

der (4) and gently work it into place.

5. Reassemble the remaining parts in reverse order

of disassembly. Make sure the gasket (3*) and

o-ring (7*) are in place. Torque the regulator seat

(12*) into the housing (5) to 175 to 200 in-lb (20 to

22 NSm). Over-tightening could break off the hex

portion of the seat.

306860 9

Parts

06864

Install with lips down.

Torque to 175 to 200 in-lb (20 to 22 NSm).

12*

Model and Series stamped on bottom.

13*

9* 1

Model 206819, Series F

Model 222405, Series B

Ref

No. Part No. Description Qty

1*** 100721 PLUG, pipe; hex socket; 1/4 npt 2

2 101954 RING, int. ret.; 0.75 in. (19 mm)

housing dia.; cadmium plated 1

3* 150670 GASKET, copper 1

4 166982 CYLINDER, regulator 1

5 177124 HOUSING, regulator 1

6 171885 WASHER, back-up; acetal

homopolymer 1

7* 166985 O-RING; PTFE 1

8 166986 SPRING, helical compression;

yellow color-coded

(Model 206819 only) 1

501511 SPRING, helical compression;

blue color-coded

(Model 222405 only) 1

9* 111796 PACKING, “U” type; PTFE 1

10 166988 LOCATOR, spring 1

11 167443 KNOB, adjusting 1

12* 204523 SEAT, regulator 1

13* 238932 PISTON, regulator 1

* These parts are included in Repair Kit 220135,

which may be purchased separately.

** These parts are included in Repair Kit 239000

(Model 238926) and Repair Kit 17M564 (Model

26A081), which may be purchased separately.

*** Plugs are shipped loose and must be installed in

unused ports. Apply anaerobic pipe sealant prior to

installation.

Model 238926, Series A

Model 26A081, Acid Compatible

Ref

No. Part No. Description Qty

1 101970 PLUG, pipe; hex socket; 1/4 npt 2

2 113751 RING, int. ret.; 0.75 in. (19 mm)

housing dia.; stainless steel 1

3** GASKET; acetal homopolymer 1

189817 (Model 238926 only)

17K950 (Model 26A081 only)

4 191840 CYLINDER, regulator 1

5 HOUSING, regulator 1

191841 (Model 238926 only)

17K951 (Model 26A081 only)

6 WASHER, back-up; acetal

homopolymer 1

171885 (Model 238926 only)

121169 (Model 26A081 only)

7** 166985 O-RING; PTFE 1

8 SPRING, helical compression;

yellow color-coded 1

166986 (Model 238926 only)

501511 (Model 26A081 only)

9** 111796 PACKING, “U” type; PTFE 1

10 166988 LOCATOR, spring 1

11 167443 KNOB, adjusting 1

12** SEAT, regulator 1

238933 (Model 238926 only)

17K953 (Model 26A081 only)

13** PISTON, regulator 1

238932 (Model 238926 only)

26A082 (Model 26A081 only)

10 306860

Notes

Andere Handbücher für SERIES F

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Graco Controller Handbücher

Graco

Graco 311595C Stücklistenhandbuch

Graco

Graco PRECISION MIX 949-999 Bedienungsanleitung

Graco

Graco H Series Bedienungsanleitung

Graco

Graco 24W482 Bedienungsanleitung

Graco

Graco Reactor 2 H-30 Betriebsanleitung

Graco

Graco 24N468 Bedienungsanleitung

Graco

Graco PRECISIONMIX 231-119 Bedienungsanleitung

Graco

Graco 24G621 Stücklistenhandbuch

Graco

Graco Series A Stücklistenhandbuch

Graco

Graco 217075 Bedienungsanleitung

Graco

Graco 214895 Bedienungsanleitung

Graco

Graco 26A814 Bedienungsanleitung

Graco

Graco 3A7639A Bedienungsanleitung

Graco

Graco 248921 310798D Stücklistenhandbuch

Graco

Graco 238890 Bedienungsanleitung

Graco

Graco P20-VM Bedienungsanleitung

Graco

Graco Harrier EZ-Batch Bedienungsanleitung

Graco

Graco ProControl 1KS Bedienungsanleitung

Graco

Graco PrecisionFlo XL Bedienungsanleitung

Graco

Graco 214706 Bedienungsanleitung

Graco

Graco InvisiPac HM25 Gebrauchs- und Pflegehandbuch

Graco

Graco Series B Bedienungsanleitung

Graco

Graco 114-459 Bedienungsanleitung

Graco

Graco C Series Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch