Graco MAGNUM Bedienungsanleitung
SETUP
START UP – FLUSHING
Connect hose to gun. Remove
red cap, connect hose to sprayer.
Securely tighten.
Read Owner’s Manual for complete
instructions and warnings.
This quick guide is not a substitute for reading
and understanding all instruction manuals and
warning labels supplied with the equipment.
Manuals are available at magnum.graco.com
Follow pressure
relief procedure and wear
protective equipment
including but not limited to
protective eye wear.
SKIN INJECTION
HAZARD: Keep clear
of spray tip and leaks.
Engage trigger lock
when not spraying.
FIRE AND EXPLOSION
HAZARD: Follow
fire and explosion
warnings as listed in
your manual.
Turn Power Switch
OFF
and plug
sprayer into grounded outlet.
Turn gun trigger lock to locked
position. Unthread spray tip
and guard assembly.
Separate small, clear drain tube
from large suction tube and place
into waste pail.
Turn Pressure Control Knob
to lowest setting.
Allow fluid to flow out drain tube
for 30-60 seconds. Turn Power
Switch
OFF
.
With the Prime/Spray Valve down to
PRIME
, press PushPrime™button twice,
turn Pressure Control Knob to Prime/Clean setting. Turn Power Switch
ON
.
QUICK GUIDE
1
1
4
2
5
3
Submerge suction tube in water
if spraying water-based material
or flushing fluid if spraying
oil-based.
1
32
FAILURE TO FOLLOW ALL WARNINGS CAN RESULT IN SERIOUS INJURY, AMPUTATION, OR DEATH.
START UP – FILL PUMP, GUN & HOSE WITH PAINT
Trigger gun into waste pail, turn Prime/Spray Valve forward to
SPRAY
and turn Power Switch
ON
.
When paint comes out of the gun, release trigger. Turn gun trigger lock to locked position. Thread spray tip and
guard assembly to gun.
Attach drain tube to suction tube and turn Pressure Control Knob to Spray Setting. Start at lowest
setting and increase until pattern is evenly distributed, no gaps at edge.
YOU ARE NOW READY TO SPRAY!
1
2
3
4
Submerge suction tube in paint. Turn Power Switch
ON
and wait to see paint coming into the drain tube.
Turn Power Switch
OFF
.
1500 psi
103 bar/10.3 MPa
3000 psi
207 bar/20.7 MPa
Good
spray pattern
tails- gaps at edges
pressure
too low
2
CLEAN UP: WATER-BASED PAINTS (see Owner’s Manual for oil-based paints)
3
Turn Power Switch
OFF
. Place suction and drain tubes in waste pail. Turn Prime/Spray Valve down to
PRIME
.
Turn Pressure Control Knob to Prime/Clean setting. Trigger gun into waste pail.
Unscrew inlet strainer from suction tube and place
in waste pail for cleaning. Thread Power Flush
attachment to suction tube. Turn Power Switch
ON
and let water run through drain tube for
20 seconds. Turn Power Switch
OFF
.
Turn Pressure Control Knob to lowest setting and release
trigger. Turn gun trigger lock to locked position. Turn Prime/
Spray Valve down to
PRIME
. Turn Power Switch
OFF
.
With the trigger lock in locked position, unthread spray tip and
guard assembly from gun. Place in waste pail for further cleaning.
TO SAVE PAINT IN HOSE
: Trigger gun into paint pail,
turn Prime/Spray Valve forward to
SPRAY
and turn Power
Switch
ON
. When water comes out of gun, keep gun
triggered and aim into waste pail. Continue to flush until
water runs clear.
Clean spray tip, guard, inlet strainer with
brush. Remove gun filter and clean.
Reassemble gun filter, spray tip and guard.
Thread Power Flush™attachment onto
garden hose, turn water on. Rinse paint
off of suction and drain tubes,
inlet screen and spray tip/guard.
1
2
4
6
5
7
3
STORAGE FLUID
Remove Power Flush attachment from suction tube.
Submerge suction tube in Pump Armor.™Turn Prime/Spray Valve down to
PRIME
. Turn Power
Switch
ON
. Turn Pressure Control Knob to Prime/Clean
setting.
When Pump Armor comes out of drain tube,
turn Pressure Control Knob to lowest setting
and Power Switch
OFF
.
Turn Prime/Spray Valve to
SPRAY
and install inlet
strainer on suction tube for storage.
Every Graco purchase comes
with A+ Customer Service.
Questions?
(888)541-9788
magnum.graco.com/aplus
1
3
2
4
magnum.graco.com/magop
4
3A3526 Revision B, May 2016. Original Instructions.This Quick Guide contains English.
Source Manuals: 3A3208, 3A3529 MM 3A3526. Copyright 2016
Scan QR code for
Operational Video
Andere Graco Spritzpistole Handbücher
Graco
Graco ULTRA 600 231-307 Series A Bedienungsanleitung
Graco
Graco 24H685 Fehlerbehebungshandbuch
Graco
Graco IronMan 256790 Leitfaden
Graco
Graco Reactor E-10 Bedienungsanleitung
Graco
Graco Pro Xp L40T10 Stücklistenhandbuch
Graco
Graco 3A4803A Leitfaden
Graco
Graco Ultra Max II 695 Handbuch
Graco
Graco Reactor H-25 Series Bedienungsanleitung
Graco
Graco Reactor A-XP Series Bedienungsanleitung
Graco
Graco PROX19 Bedienungsanleitung
Graco
Graco Husky 224-833 Bedienungsanleitung
Graco
Graco RTX-650 Programmierhandbuch
Graco
Graco 240-349 Bedienungsanleitung
Graco
Graco 310778N Betriebsanleitung
Graco
Graco Ultra Max 309273 Bedienungsanleitung
Graco
Graco WB100 Bedienungsanleitung
Graco
Graco 231-077 Bedienungsanleitung
Graco
Graco 223963 Bedienungsanleitung
Graco
Graco 24G775 Bedienungsanleitung
Graco
Graco Reactor H-VR Bedienungsanleitung
