Graco ST Max 395 Hopper Handbuch

www.graco.be

ST Max™395

ST Max™II 495/595

SETUP

Connect hose to sprayer and gun.

Tighten hose connections with wrench. Unscrew tip & guard from gun.

Fill throat packing nut with TSL™

to prevent premature packing wear.

Make sure power

switch is set to OFF.

Plug electrical cord

into grounded outlet.

Turn prime valve

to Prime position (down).

Place siphon tube in pail

partially filled with water.

Turn pressure control knob

to lowest pressure, and set

power switch to ON.

Increase pressure until

sprayer starts and water

runs out of prime tube.

Let water run out of prime

tube for 15 seconds.

Decrease pressure

until sprayer stops.

Turn prime valve

to Spray position

(horizontal).

Make sure safety

lever of gun is OFF.

Aim gun at inside

wall of water pail

and squeeze trigger.

Increase pressure until

sprayer starts. Keep gun

triggered into water pail for

1 minute. Release trigger.

Turn prime

valve to Prime

position (down).

Place siphon tube in paint

pail, but leave drain tube

in water pail.

Aim gun at inside

wall of water pail,

and squeeze trigger.

Transfer drain

tube to paint pail.

Increase pressure until

sprayer starts and paint

comes out of drain tube.

Keeping gun triggered into water

pail, turn prime valve

to Spray position (horizontal).

When paint comes out of gun,

release trigger and turn safety

lever of gun to ON.

Screw tip & guard onto gun, making sure

arrow-shaped handle of tip is pointing forward.

You can reverse this tip to quickly clear clogs

without taking it apart.

This procedure is for water-base paints and flushing fluids. For solvent-base paints and flushing

fluids (i.e. mineral spirits), you must read Fire and Explosion Hazard in the Operating Instructions.

* check the Graco operations manual delivered with the unit for more details.

CHOOSE THE RIGHT TIP & FILTER

WARNING

Quick Operator’s Guide

207

307

109

209

309

409

509

609

111

211

311

411

511

611

113

213

313

413

513

613

115

215

315

415

515

615

815

217

317

417

517

617

817

917

119

219

319

419

519

619

819

121

221

321

421

521

621

721

821

223

323

423

523

623

723

225

325

425

525

625

725

327

427

527

627

827

429

529

629

729

331

531

631

831

433

533

633

833

235

435

535

635

735

835

935

439 443

543

645

451

551

455

555

655

5 cm

10 cm

15 cm

20 cm

25 cm

30 cm

35 cm

40 cm

45 cm

3 cm

7 cm

10 cm

15 cm

20 cm

25 cm

30 cm

35 cm

40 cm

pump ﬁlter

gun ﬁlter

200 mesh

100 mesh

60 mesh

none

30 mesh

* at 30 cm spraying distance

Ink

Stains

Lacquers

Enamels

Urethanes

Acrylics

Emulsions

Latex

Block ﬁller

Intumescents

Texture material

for spray applications 1st digit X5

=fan width*

Time to

change!

NEW WORN

SPRAYING

Turn safety lever

of gun to OFF.

Point gun at area to be sprayed about 30 cm from surface, and begin moving gun before triggering. A good spray pattern is evenly

distributed as it hits surface. Set pressure just high enough to spray without heavy edges. Use smaller tip size for thinner material

and a larger tip size for thicker material if pressure adjustment cannot achieve even spray pattern.

SHUTDOWN AND CLEANUP

Set power

switch to OFF.

Trigger gun

until pressure

is relieved.

Turn prime valve

to Prime position (down).

Remove gun

filter assembly.

Unscrew tip & guard from

gun. Clean gun filter, inlet

screen, tip, guard and

manifold filter with water

and brush.

Set power switch to ON,

and increase pressure

until sprayer starts.

As soon as Pump Armor

comes out of drain tube,

set power switch to OFF.

Screw inlet screen onto

siphon tube, replace

manifold filter and spacer,

and assemble gun with

filter, tip and guard.

Wipe outside of sprayer,

hose and gun with rag

soaked in water or

mineral spirits.

Fill throat packing

nut with TSL.™

Place drain tube

and siphon tube

in pail of water.

Turn pressure control knob to

lowest setting, set power switch

to ON, and increase pressure until

sprayer starts. Let sprayer run and

flush itself for 2 minutes.

Keeping gun triggered

into water pail, turn prime

valve to Spray position

(horizontal).

Set power switch to OFF, turn

pressure control knob to lowest

setting, and turn prime valve to

Prime position (down).

Place drain tube in waste

pail and siphon tube in

container of Pump Armor™

Assemble gun

without filter.

Unscrew inlet screen

from siphon tube.

WASTE

Keep gun triggered

into pail for 1 minute,

until water coming out

of gun is clean.

Remove manifold

filter and spacer.

GRACO N.V. Industrieterrein Oude Bunders

Slakweidestraat 31 • B-3630 Maasmechelen

Tel: +32 (89) 770 700 • Fax: +32 (89) 770 777

E-mail: [email protected] • http://www.graco.be

All information, illustrations, and specifications in this document are based on the latest product information

available at the time of publication. The right is reserved to make changes at any time without notice.

Graco is certified ISO 9001.

Andere Handbücher für ST Max 395 Hopper

Dieses Handbuch passt für folgende Modelle

Andere Graco Spritzpistole Handbücher

Graco

Graco 207-279 Bedienungsanleitung

Graco

Graco 240054 Bedienungsanleitung

Graco

Graco GH 200 Bedienungsanleitung

Graco

Graco 18H269 Bedienungsanleitung

Graco

Graco SUPER NOVA SP Bedienungsanleitung

Graco

Graco AirPro EFX Stücklistenhandbuch

Graco

Graco ULTIMATE Mx 1595 Bedienungsanleitung

Graco

Graco Magnum 309045K Bedienungsanleitung

Graco

Graco 238338 Bedienungsanleitung

Graco

Graco Pro Pack 24F893 Bedienungsanleitung

Graco

Graco SaniSpray HP 130 Gebrauchs- und Pflegehandbuch

Graco

Graco GMAX 258731 Bedienungsanleitung

Graco

Graco HTX 257369 Betriebsanleitung

Graco

Graco LineLazer IV Series Bedienungsanleitung

Graco

Graco 3A0149C Datenblatt

Graco

Graco EM 390 Bedienungsanleitung

Graco

Graco M2K Stücklistenhandbuch

Graco

Graco TX 65 Bedienungsanleitung

Graco

Graco 24V112 Bedienungsanleitung

Graco

Graco Ultra 395 Bedienungsanleitung

Graco

Graco Fuller O'brien Paints Pro 501st Series Bedienungsanleitung

Graco

Graco SDX Betriebsanleitung

Graco

Graco M2K 17D763 Stücklistenhandbuch

Graco

Graco ST Einrichtungshandbuch

Beliebte Spritzpistole Handbücher anderer Marken

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Bedienungsanleitung

Binks

Binks SV100 Bedienungsanleitung

Fimco

Fimco LG-4-3-1 Bedienungsanleitung

AG SPRAY

AG SPRAY FS-ATV-25BL Bedienungsanleitung

Nordson

Nordson MicroMax 2 Bedienungsanleitung

Bonide

Bonide 051 Bedienungsanleitung

zogics

zogics Z-DAS Bedienungsanleitung

KISANKRAFT

KISANKRAFT KK-KBS-165 Bedienungsanleitung

Matrix

Matrix SG 650 Bedienungsanleitung

Anest Iwata

Anest Iwata SGA-3 Kurzanleitung

paasche

paasche VV Datenblatt

Carlisle

Carlisle DeVilbiss JGA-510 Bedienungsanleitung

Gardena

Gardena 11120 Bedienungsanleitung

Conrad

Conrad Hobby Airbrush K3 Bedienungsanleitung

wiwa

wiwa 14025 R/F Bedienungsanleitung

DeVilbiss

DeVilbiss LUNA2i Bedienungsanleitung

WAGNER

WAGNER W 125 Bedienungsanleitung

My Clean Buddy

My Clean Buddy PW018 Bedienungsanleitung