Graco 25C782 Bedienungsanleitung

Instructions and Parts

SaniForce™

Sanitary Drum

Pumps

For use in sanitary applications to transfer medium to high viscosity fluids. Not approved

for use in explosive atmospheres or hazardous locations. For professional use only.

See page 3 for model information, including maximum fluid working pressure.

Important Safety Instructions

Careless pump operation can result in

serious injury. Read all warnings and

instructions in this manual. Save these

instructions.

Model 25C420 Shown

3A4586E

2 3A4586E

Contents

Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Electrical Connections (17N668 Motor) . . . . . . . . 7

Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Pre-Start Checklist . . . . . . . . . . . . . . . . . . . . . . . 9

Flush Before First Use . . . . . . . . . . . . . . . . . . . . 9

Tighten Connections . . . . . . . . . . . . . . . . . . . . . . 9

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Initial Configuration (17N668 motor with Graco

VFD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Graco VFD Operation (17N668 motor) . . . . . . . 11

Pump Shutdown . . . . . . . . . . . . . . . . . . . . . . . . 12

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Flushing Procedure . . . . . . . . . . . . . . . . . . . . . . 14

Cleaning Procedure . . . . . . . . . . . . . . . . . . . . . 14

Models 25C411 - 25C414 . . . . . . . . . . . . . . . . . 15

Models 25C416 - 25C419, 25C776 - 25C779 . . 17

Models 25C420, 25C421, 25C422, 25C780,

25C781, 25C782 . . . . . . . . . . . . . . . . . . . . 19

17N666 and 17N667 Motor Maintenance . . . . . 21

Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Complete Pump Models 25C411, 25C412, 25C413,

and 25C414 . . . . . . . . . . . . . . . . . . . . . . . . 24

Complete Pump Models 25C420, 25C421, 25C780,

25C781 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Complete Pump Models 25C416 - 25C419,

25C776 - 25C779 . . . . . . . . . . . . . . . . . . . . 28

Complete Pump Model 25C422, 25C782 . . . . . 30

Performance Charts . . . . . . . . . . . . . . . . . . . . . . . . 32

Models 25C411 - 25C419, 25C776 - 25C779 . . 32

Models 25C420 - 25C421, 25C780 - 25C781 . . 33

Model 25C422, 25C782 . . . . . . . . . . . . . . . . . . . 34

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Models 25C411, 25C412, 25C416, 25C417,

25C776, 25C777 . . . . . . . . . . . . . . . . . . . . . 35

Models 25C413, 25C414, 25C418, 25C419,

25C778, 25C779 . . . . . . . . . . . . . . . . . . . . . 35

Models 25C420, 25C421, 25C780, 25C781 . . . 36

Models 25C422, 25C782 . . . . . . . . . . . . . . . . . . 36

Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Models

3A4586E 3

Models

ETL Label

System

Model

Motor Lower Unit Motor

ApprovalsModel Type Model Length Notes

Impeller

25C411 17N666 115 VAC, variable speed † 17N669 39 inches See ETL label

25C413 17N666 115 VAC, variable speed † 17N670 47 inches

25C412 17N667 230 VAC, Euro plug, variable speed ‡ 17N669 39 inches

25C414 17N667 230 VAC, Euro plug, variable speed ‡ 17N670 47 inches

High Volume See ETL label

25C416 17N666 115 VAC, variable speed † 17N671 39 inches

25C417 17N667 230 VAC, Euro plug, variable speed ‡ 17N671 39 inches

25C418 17N666 115 VAC, variable speed † 17N672 47 inches

25C419 17N667 230 VAC, Euro plug, variable speed ‡ 17N672 47 inches

High Pressure

25C776 17N666 115 VAC, variable speed † 17S148 39 inches

25C777 17N667 230 VAC, Euro plug, variable speed ‡ 17S148 39 inches

25C778 17N666 115 VAC, variable speed † 17S149 47 inches

25C779 17N667 230 VAC, Euro plug, variable speed ‡ 17S149 47 inches

Progressive Cavity ◆

25C780 17N666 115 VAC, variable speed † 17S150 39 inches bag-liner

foot See ETL label

25C420 17N666 115 VAC, variable speed † 17N673 39 inches

25C781 17N667 230 VAC, Euro plug, variable speed ‡ 17S150 39 inches bag-liner

foot

25C421 17N667 230 VAC, Euro plug, variable speed ‡ 17N673 39 inches

25C422* 17N668 190/380 or 230/460 VAC, 3 phase, water

washdown 17N674 39 inches UL recognized

component

25C782* 17N668 190/380 or 230/460 VAC, 3 phase, water

washdown 17S153 39 inches bag-liner

foot

* Pump hanger 17P662 included.

† Wired with a North American “Type B” 3-pin plug.

‡ Wired with a European “Type F” 2-pin plug.

◆Pump elevator 24V310 or 24V311 can be used

with these pumps. Pump mounting bracket 24V303

may work for mounting on customer-owned eleva-

tors. These are ordered separately.

Type B Type F

Warnings

4 3A4586E

Warnings

The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama-

tion point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When

these symbols appear in the body of this manual, refer back to these Warnings. Product-specific hazard symbols and

warnings not covered in this section may appear throughout the body of this manual where applicable.

WARNING

PRESSURIZED EQUIPMENT HAZARD

Fluid from the equipment, leaks, or ruptured components can splash in the eyes or on skin and cause

serious injury.

• Follow the Pressure Relief Procedure when you stop dispensing and before cleaning, checking, or

servicing equipment.

• Tighten all fluid connections before operating the equipment.

• Check hoses, tubes, and couplings daily. Replace worn or damaged parts immediately.

MOVING PARTS HAZARD

Moving parts can pinch, cut or amputate fingers and other body parts.

• Keep clear of moving parts.

• Do not operate equipment with protective guards or covers removed.

• Pressurized equipment can start without warning. Before checking, moving, or servicing equipment,

follow the Pressure Relief Procedure and disconnect all power sources.

FIRE AND EXPLOSION HAZARD

Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help prevent

fire and explosion:

• Use equipment only in well ventilated area.

• Eliminate all ignition sources; such as pilot lights, cigarettes, portable electric lamps, and plastic drop

cloths (potential static arc).

• Keep work area free of debris, including solvent, rags and gasoline.

• Do not plug or unplug power cords, or turn power or light switches on or off when flammable fumes

are present.

• Ground all equipment in the work area. See Grounding instructions.

• Use only grounded hoses.

• Hold gun firmly to side of grounded pail when triggering into pail.

• If there is static sparking or you feel a shock, stop operation immediately. Do not use equipment

until you identify and correct the problem.

• Keep a working fire extinguisher in the work area.

Warnings

3A4586E 5

ELECTRIC SHOCK HAZARD

This equipment must be grounded. Improper grounding, setup, or usage of the system can cause elec-

tric shock.

• Turn off and disconnect power cord before servicing equipment.

• Connect only to grounded electrical outlets.

• Use only 3-wire extension cords.

• Ensure ground prongs are intact on power and extension cords.

• Do not expose to rain. Store indoors.

• Do not submerge the motor in liquid.

• Never carry the motor by the power cord.

EQUIPMENT MISUSE HAZARD

Misuse can cause death or serious injury.

• Do not operate the unit when fatigued or under the influence of drugs or alcohol.

• Do not exceed the maximum working pressure or temperature rating of the lowest rated system com-

ponent. See Technical Data in all equipment manuals.

• Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all

equipmentmanuals.Readfluidandsolventmanufacturer’swarnings.Forcompleteinformationabout

your material, request SDS from distributor or retailer.

• Do not leave the work area while equipment is energized or under pressure.

• Turn off all equipment and follow the Pressure Relief Procedure when equipment is not in use.

• Check equipment daily. Repair or replace worn or damaged parts immediately with genuine manu-

facturer’s replacement parts only.

• Do not alter or modify equipment.

• Make sure all equipment is rated and approved for the environment in which you are using it.

• Use equipment only for its intended purpose. Call your distributor for information.

• Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.

• Do not kink or over bend hoses or use hoses to pull equipment.

• Keep children and animals away from work area.

• Comply with all applicable safety regulations.

BURN HAZARD

Equipment surfaces and fluid that is heated can become very hot during operation. To avoid sever

burns:

• Do not touch hot fluid or equipment.

PERSONAL PROTECTIVE EQUIPMENT

You must wear appropriate protective equipment when operating, servicing, or when in the operating

area of the equipment to help protect you from serious injury, including eye injury, hearing loss, inhala-

tion of toxic fumes, and burns. This equipment includes but is not limited to:

• Protective eyewear, and hearing protection.

• Respirators, protective clothing, and gloves as recommended by the fluid and solvent manufacturer.

WARNING

Installation

6 3A4586E

Installation

Grounding

Grounding is an electrical connection between a metal

vessel, pump, or motor and a true earth ground.

Motor: Electrical cords must be connected to outlets

with electrical ground.

Pump: Ensure that the ground screw provided with the

pump is connected to a true earth ground. Insert one

end of a 14 AWG minimum ground wire behind the

ground screw and tighten the screw securely. Connect

the clamp end of the grounding wire to a true earth

ground. A ground wire and clamp, Part 238909, is avail-

able from your Graco distributor.

Fluid hoses: use only electrically conductive hoses with

a maximum of 500 ft. (150 m) combined hose length to

ensure grounding continuity. Check electrical resistance

of hoses. If total resistance to ground exceeds 25 meg-

ohms, replace hose immediately.

Material supply container: follow local code.

Container(s) that receive material: follow local code.

To maintain grounding continuity when flushing or

relieving pressure: hold metal part of the dispense

valve firmly to the side of a grounded metal pail, then

trigger the valve.

Mounting

1. Remove the pump and motor from packaging.

2. Inspect all contents for damage.

3. Install the motor with pump lower:

a. On pumps using the 17N668 motor, hang the

pump using the included motor hanger (302)

using adequate hardware, following local code.

Torque the motor hanger to 30-36 ft-lb (41-49

N-m).

b. On pumps using the 17N666 or 17N667 motor,

attach motor to pump by tightening the motor

nut on the pump.

The equipment must be grounded to reduce the risk of

static sparking and electric shock. Electric or static

sparking can cause fumes to ignite or explode.

Improper grounding can cause electric shock. Ground-

ing provides an escape wire for the electric current.

To avoid injury from a falling pump, model 25C422 or

25C782, check the connections on the motor hanger

(302) before using the motor hanger to lift the pump.

NOTICE

To avoid damaging the pump, do not overtighten the

mounting hardware.

Installation

3A4586E 7

Electrical Connections (17N668 Motor)

Wire Connections at the Motor

NOTE: Graco recommends the use of a motor soft

starter or a VFD in the electrical circuit for all installa-

tions. In all cases, make sure all products are installed in

accordance with local codes and regulations.

1. Remove 4 bolts to open the motor’s electrical box.

2. Internal Wiring:

a. For 460V Motors: The motor typically comes

wired for 460 V. If this is the voltage you want,

the existing wiring can remain as it is.

b. For 230V Motors: Move the 7, 8, and 9 wires

as shown. Bridge W2, U2, and V2 as shown.

3. Install wiring system with proper liquid-tight connec-

tions in one of the ports at the bottom of the motor

box.

4. Connect the ground wire to the ground screw.

Torque the M5 stud to 17.7 in-lb (2.0 N-m).

5. Connect power wires L1, L2 and L3 to line terminals

U1, V1, and W1.

6. Torque terminals to 14.2 in-lb (1.6 N-m). Do not

overtorque.

7. Close the motor electrical box. Torque the screws to

20 in-lb (2.3 N-m).

Wire Connections at the Variable

Frequency Drive (VFD)

NOTE: For variable speed control, the motor must be

wired to a VFD. Follow the instruction in the VFD manu-

facturer’s manual.

If you purchased an optional Graco VFD, install wiring at

the VFD as follows:

1. Connect the wires to the motor. See Wire Connec-

tions at the Motor.

2. Open the VFD’s electrical box.

3. Install the wiring system with proper liquid-tight con-

nections for incoming supply power and for outgoing

motor power.

4. Connect the ground wires for the VFD and for the

motor to the ground screw.

5. Connect the wires from the motor terminals to the

matching terminals in the VFD box, as shown.

To avoid injury from fire, explosion, or electric shock,

all electrical wiring must be done by a qualified electri-

cian and comply with all local codes and regulations.

W2 U2 V2

47 58 69

231

U1 V1 W1

W2 U2 V2

17 28 39

564

U1 V1 W1

To avoid injury from fire, explosion, or electric shock, all

electrical wiring must be done by a qualified electrician

and comply with all local codes and regulations.

• Disconnect power before servicing.

• Wait 5 minutes for capacitor discharge before

opening.

Installation

8 3A4586E

6. Connect the power supply wires to the power termi-

nals in the VFD box. See the following table and fig-

ures, as applicable to your system.

7. Close the VFD electrical box.

8. Perform the VFD configuration.

U/T1V/T2W/T3PE

PES

VFD

Part No. HP Nominal Input Voltage Input Voltage

Range Nominal Output

Voltage† See Figure

16K909 1.5 120 Vac, 1 phase 90-132 Vac 240 Vac, 3 phase FIG. 1

16K909 1.5 240 Vac, 1 phase 170-264 Vac 240 Vac, 3 phase FIG. 2

16K910 1.5 208-240 Vac, 1 phase 170-264 Vac 208-240 Vac, 3 phase FIG. 3

16K910 1.5 208-240 Vac, 3 phase 170-264 Vac 208-240 Vac, 3 phase FIG. 4

† Output voltage is dependent on input voltage.

FIG. 1 120 Vac 1 Phase Input/240 Vac 3 Phase Output

FIG. 2 240 Vac 1 Phase Input/240 Vac 3 Phase Output

PE L1L2N

PE L1N

PE L1L2N

PE L1L2

FIG. 3 208-240 Vac 1 Phase Input/208-240 Vac 3

Phase Output

FIG. 4 190, 208-240 Vac 3 Phase Input/190, 208-240

Vac 3 Phase Output

PE L1L2L3

PE L1N

PE L1L2L3

Setup

3A4586E 9

Setup

Accessories are available from Graco. Make certain all

accessories are sized and pressure-rated to meet your

system requirements.

• Verify that the motor voltage corresponds to proper

electrical supply. Before plugging motor into power

supply, make sure the motor switch is in the OFF

position.

• Before operation, confirm all pump connections are

properly tightened.

• Before starting the pump, confirm the discharge

hose is securely fastened to the receiving vessel in

order to prevent splashing.

Pre-Start Checklist

Verify each of the following items before starting the

pump.

•DEBRIS: Ensure that the fluid supply is free of dirt,

debris, and any contaminants.

•HOSE MATERIAL: Check that the hose material is

compatible with the fluid being pumped. Consult

your Graco distributor for available hose materials.

•FASTENERS: Check that all fasteners are properly

tightened.

•LEAKS: Check the connections on the fluid outlet to

be sure there are no leaks.

Flush Before First Use

The sanitary pump was assembled using sanitary lubri-

cant on moving parts and was tested in water. Flush the

pump thoroughly with an appropriate cleaning solution,

and disassemble and sanitize the parts before using the

pump. See Flushing Procedure, page 14. Check

national, state, and local codes for specific limitations.

Tighten Connections

Before each use, check all hoses for wear or damage.

Replace as necessary. Check that all connections are

tight and leak-free.

Operation

10 3A4586E

Operation

1. Use closed top drum or other cover to prevent pos-

sible contamination.

2. Once the pump is fully cleaned, assembled, and all

connections are securely fastened, insert the pump

into the drum or tank.

3. It is recommended to attach a suitable hose or pipe

to the pump discharge.

4. If you opt to use a hose:

a. Ensure that the hose meets the pump discharge

pressure requirements. It is recommended to

use a hose that is rated 4x the pump discharge

pressure.

b. Fasten the hose to the hose barb with a suitable

hose clamp that exceeds the pump discharge

pressure. A hose barb fitting kit, part 25C502, is

available from your Graco distributor.

5. Variable speed pumps should be started at approxi-

mately half speed according to the dial settings.

Turn the motor to the ON position. Throttle flow to

desired output pressure by varying the potentiome-

ter (motors 17N666 and 17N667) or VFD frequency,

if applicable on motor 17N668.

6. After use, flush and clean the pump. Then store the

pump vertically.

• Moving parts can pinch, cut or amputate fingers

and other body parts. Keep your hands and fingers

away from the mechanical seal viewing window on

models 25C422 or 25C782 during operation and

whenever the pump is connected to a power

source. Disconnect power before moving.

• Do not use these pumps for the transfer of

flammable or combustible products or in an

environment where flammable or combustible

fumes are present.

• Do not clean or flush the pump with flammable or

combustible fluids.

• Progressive cavity pumps are positive displace-

ment pumps and should never be operated

against shut-off elements such as nozzles, valves,

etc. Failure to comply may result in excessive

pressure build resulting in serious injury and pump

damage.

NOTICE

• Never allow the pump to run dry of fluid. A dry

pump will possibly damage itself.

• Progressive cavity pumps 25C420, 25C421,

25C780, and 25C781 are recommended for inter-

mittent duty use only to prevent premature motor

wear. (i.e., 30 minute intervals with a 10 minute

cooling off period). For continuous duty applica-

tions, Graco recommends using models 25C422 or

25C782.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Graco Wasserpumpe Handbücher

Graco

Graco Husky 1050HP Bedienungsanleitung

Graco

Graco Hydra-Spray 224-623 Bedienungsanleitung

Graco

Graco Dyna-Star 77X100 Gebrauchs- und Pflegehandbuch

Graco

Graco Dyna-Star 247540 Gebrauchs- und Pflegehandbuch

Graco

Graco C Series Bedienungsanleitung

Graco

Graco Fast-Flo Datenblatt

Graco

Graco saniforce 2150 Handbuch

Graco

Graco Series A Bedienungsanleitung

Graco

Graco Falcon A Series Bedienungsanleitung

Graco

Graco Husky 2200 Bedienungsanleitung

Graco

Graco Dura-Flo 900 Series Bedienungsanleitung

Graco

Graco HYDRA-CAT FIXED RATIO Bedienungsanleitung

Graco

Graco 5:1 Fire-Ball 300 Bedienungsanleitung

Graco

Graco Ratio King A Series Datenblatt

Graco

Graco President C Series Bedienungsanleitung

Graco

Graco TRITON D Series Bedienungsanleitung

Graco

Graco E-Flo Plus Bedienungsanleitung

Graco

Graco Monark A Series Bedienungsanleitung

Graco

Graco G Series Bedienungsanleitung

Graco

Graco Dura-Flo A Series Bedienungsanleitung

Graco

Graco Hydra-Clean 1040 Handbuch

Graco

Graco DM-22 Bedienungsanleitung

Graco

Graco Husky 2150e Gebrauchs- und Pflegehandbuch

Graco

Graco 239923 Bedienungsanleitung

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

moyno

moyno 2000 CC Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung

STA-RITE

STA-RITE ST33APP Bedienungsanleitung