Graco Check-Mate L500CM Bedienungsanleitung

Instructions - Parts

Ink Pump Packages

For use with medium to high viscosity inks. For professional use only.

Not for use in explosive atmospheres.

With priming piston and MaxLife®rod and cylinder.

Important Safety Instructions

Read all warnings and instructions in this manual.

Save these instructions.

ti14639a

Package with NXT Air Motor

and

L500CM Displacement Pump

See page 3 for model information, including

maximum working pressures. Package with Viscount II

Hydraulic Motor and L500CM

Displacement Pump

ti14637a

Package with NXT Air Motor,

DataTrak™, and L200CM

Displacement Pump

ti14636a

3A0096B

ENG

Related Manuals

23A0096B

Contents

Related Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Ink Pump Packages . . . . . . . . . . . . . . . . . . . . . . . . . 3

Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Grounding (All Pumps) . . . . . . . . . . . . . . . . . . . . 7

Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Air-Powered Pumps . . . . . . . . . . . . . . . . . . . . . . 8

Hydraulic-Powered Pumps . . . . . . . . . . . . . . . . 10

Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Tighten Clamps . . . . . . . . . . . . . . . . . . . . . . . . . 12

Wet Cup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Wet Cup Drain Fitting . . . . . . . . . . . . . . . . . . . . 12

Torque Wet Cup . . . . . . . . . . . . . . . . . . . . . . . . 12

Pressure Relief Procedure . . . . . . . . . . . . . . . . . . 13

Prime/Flush . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Start Up and Adjust Pump . . . . . . . . . . . . . . . . . . 14

Air-Powered Pumps . . . . . . . . . . . . . . . . . . . . . 14

Hydraulic-Powered Pumps . . . . . . . . . . . . . . . . 14

All Pumps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Air-Powered Ink Packages . . . . . . . . . . . . . . . . 16

258753 Hydraulic-Powered Ink Package . . . . . 17

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Graco Standard Warranty . . . . . . . . . . . . . . . . . . . 20

Graco Information . . . . . . . . . . . . . . . . . . . . . . . . 20

Related Manuals

Component Manuals in English

Manual Description

312375 Check-Mate®Displacement Pump

Instructions-Parts

312376 Check-Mate®Pump Packages

Instructions-Parts

312468 200 cc Check-Mate Displacement

Pump Repair Parts Manual

312470 500 cc Check-Mate Displacement

Pump Repair Parts Manual

311238 NXT Air Motor Instructions-Parts

307158 Viscount®II Hydraulic Motor

Instructions-Parts

3A0133

24C743 and 24C744 King™Air

Motor Conversion Kits;

24D625 Viscount®II Hydraulic

Motor Conversion Kit

Ink Pump Packages

3A0096B 3

Ink Pump Packages

Check your pump package’s identification plate for the 6-digit part number of your pump package.

To order replacement parts, see Parts section starting on page 16.

Ink Pump

Package

Part No. Series Ratio

Data Monitoring

Power

Source

Pump

Size

Maximum Air

or Hydraulic

Input Pressure

psi (MPa, bar)

Maximum Fluid

Working

Pressure

psi (MPa, bar)None DataTrak

Remote

DataTrak

258744 A 14:1 ✔Air 500 cc 100 (0.7, 7.0) 1400 (9.7, 97)

258745 A 14:1 ✔Air 500 cc 100 (0.7, 7.0) 1400 (9.7, 97)

258746 A 14:1 ✔Air 500 cc 100 (0.7, 7.0) 1400 (9.7, 97)

258747 A 23:1 ✔Air 200 cc 100 (0.7, 7.0) 2300 (15.9, 159)

258748 A 23:1 ✔Air 200 cc 100 (0.7, 7.0) 2300 (15.9, 159)

258749 A 23:1 ✔Air 200 cc 100 (0.7, 7.0) 2300 (15.9, 159)

258750 A 26:1 ✔Air 500 cc 100 (0.7, 7.0) 2600 (17.9, 179)

258751 A 26:1 ✔Air 500 cc 100 (0.7, 7.0) 2600 (17.9, 179)

258752 A 26:1 ✔Air 500 cc 100 (0.7, 7.0) 2600 (17.9, 179)

258753 A 1.6:1 ✔Hydraulic

Oil

500 cc 1500 (10, 103) 2300 (15.9, 159)

Package Identification Plate

ti14691a ti14690a

ti14689a

Location on Air-Powered

Packages

Location on

Hydraulic-Powered

Packages

Warnings

43A0096B

Warnings

The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama-

tion point symbol alerts you to a general warning and the hazard symbol refers to procedure-specific risk. Refer back

to these warnings. Additional, product-specific warnings may be found throughout the body of this manual where

applicable.

WARNING

SKIN INJECTION HAZARD

High-pressure fluid from gun, hose leaks, or ruptured components will pierce skin. This may look like just

a cut, but it is a serious injury that can result in amputation. Get immediate surgical treatment.

• Do not point gun at anyone or at any part of the body.

• Do not put your hand over the spray tip.

• Do not stop or deflect leaks with your hand, body, glove, or rag.

• Do not spray without tip guard and trigger guard installed.

• Engage trigger lock when not spraying.

• Follow Pressure Relief Procedure in this manual, when you stop spraying and before cleaning,

checking, or servicing equipment.

MOVING PARTS HAZARD

Moving parts can pinch or amputate fingers and other body parts.

• Keep clear of moving parts.

• Do not operate equipment with protective guards or covers removed.

• Pressurized equipment can start without warning. Before checking, moving, or servicing equipment,

follow the Pressure Relief Procedure in this manual. Disconnect power or air supply.

FIRE AND EXPLOSION HAZARD

Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help prevent

fire and explosion:

• Use equipment only in well ventilated area.

• Eliminate all ignition sources; such as pilot lights, cigarettes, portable electric lamps, and plastic drop

cloths (potential static arc).

• Keep work area free of debris, including solvent, rags and gasoline.

• Do not plug or unplug power cords, or turn power or light switches on or off when flammable fumes

are present.

• Ground all equipment in the work area. See Grounding instructions.

• Use only grounded hoses.

• Hold gun firmly to side of grounded pail when triggering into pail.

• If there is static sparking or you feel a shock, stop operation immediately. Do not use equipment

until you identify and correct the problem.

• Keep a working fire extinguisher in the work area.

Warnings

3A0096B 5

EQUIPMENT MISUSE HAZARD

Misuse can cause death or serious injury.

• Do not operate the unit when fatigued or under the influence of drugs or alcohol.

• Do not exceed the maximum working pressure or temperature rating of the lowest rated system

component. See Technical Data in all equipment manuals.

• Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all

equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete information

about your material, request MSDS forms from distributor or retailer.

• Check equipment daily. Repair or replace worn or damaged parts immediately with genuine manu-

facturer’s replacement parts only.

• Do not alter or modify equipment.

• Use equipment only for its intended purpose. Call your distributor for information.

• Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.

• Do not kink or over bend hoses or use hoses to pull equipment.

• Keep children and animals away from work area.

• Comply with all applicable safety regulations.

TOXIC FLUID OR FUMES HAZARD

Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or

swallowed.

• Read MSDS’s to know the specific hazards of the fluids you are using.

• Store hazardous fluid in approved containers, and dispose of it according to applicable guidelines.

• Always wear impervious gloves when spraying or cleaning equipment.

PERSONAL PROTECTIVE EQUIPMENT

You must wear appropriate protective equipment when operating, servicing, or when in the operating

area of the equipment to help protect you from serious injury, including eye injury, inhalation of toxic

fumes, burns, and hearing loss. This equipment includes but is not limited to:

• Protective eyewear

• Clothing and respirator as recommended by the fluid and solvent manufacturer

•Gloves

• Hearing protection

WARNING

Warnings

63A0096B

Installation

3A0096B 7

Installation

Grounding (All Pumps)

The equipment must be grounded. Grounding reduces

the risk of static and electric shock by providing an

escape wire for the electrical current due to static build

up or in the event of a short circuit.

Pump: use the ground wire and clamp supplied.

Remove the ground screw (air-powered packages) or

loosen the grounding lug locknut and washer (hydrau-

lic-powered packages). Install the 1.5 mm2(12 ga) mini-

mum ground wire and tighten the screw or locknut

securely. Connect the clamp to a true earth ground.

Air and fluid hoses: use only electrically conductive

hoses.

Air compressor: follow manufacturer's recommenda-

tions.

Dispense valve: ground through connection to a prop-

erly grounded fluid hose and pump.

Fluid supply container: follow your local code.

Object being sprayed: follow your local code.

Solvent pails used when flushing: follow local code.

Use only conductive metal pails, placed on a grounded

surface. Do not place the pail on a nonconductive sur-

face, such as paper or cardboard, which interrupts

grounding continuity.

To maintain grounding continuity when flushing or

relieving pressure: hold metal part of the dispense

valve firmly to the side of a grounded metal pail, then

trigger the valve.

Location

When selecting the location for the pump, keep the fol-

lowing in mind:

• There must be sufficient space on all sides of the

pump for installation, operator access, repair, and

air circulation. See Dimensions, page 18.

• Ensure that the floor stand (2) is level in all direc-

tions. If necessary, level the stand using metal

shims. Secure the stand to the floor using 1/2 in. (13

mm) anchors that are long enough to prevent the

pump from tipping. See Dimensions, page 18, for

mounting hole layout.

FIG. 1. Ground Wire

ti8250a

Installation

83A0096B

Air-Powered Pumps

• Reference numbers and letters in parentheses in

the text refer to numbers and letters in the illustra-

tions.

•F

IG. 2, page 9, shows a typical installation of an

air-powered pump. It is only a guide. Contact your

Graco distributor for actual system designs.

• Be sure all accessories, including air lines and fluid

lines, are adequately sized and pressure-rated to

meet system requirements.

• Use only electrically conductive hoses. Fluid hoses

must have spring guards on both ends.

Air Line Accessories

Install the following accessories as shown in FIG. 2,

using adapters as necessary.

•Bleed type master air valve (J) is required in your

system to shut off the air supply to the pump. When

closed, the valve will bleed off all air in the pump. Be

sure the valve is easily accessible from the pump.

•Air regulator (H) controls pump speed and outlet

pressure by adjusting the air pressure to the pump.

Locate the regulator close to the pump, but

upstream from the bleed-type master air valve.

•Air line filter (L) removes harmful dirt and moisture

from the compressed air supply. Also, install a drain

valve at the bottom of each air line drop, to drain off

moisture.

•Air shutoff relief valve (M) isolates the air line

accessories for servicing. Locate upstream from all

other air line accessories.

•DataTrak: see the NXT air motor manual 311238 for

DataTrak information.

Fluid Line Accessories

Install the following accessories as shown in FIG. 2,

using adapters as necessary.

• Install a fluid shutoff valve at each valve drop, to

isolate the valve and fluid accessories for servicing.

• Install a fluid drain valve near the pump fluid outlet,

and at each valve station. The drain valves are

required in your system to relieve fluid pressure in

the displacement pump, hose and valve. Drain

valves at the valve stations may be mounted in the

base of a fluid regulator, using an adapter.

•Fluid regulator controls fluid pressure to the valve,

and dampens pressure surges.

•Dispense valve dispenses the fluid.

•Valve swivel allows freer valve movement.

A bleed type master air valve (J) is required to help

reduce the risk of serious injury, including fluid injection

and splashing of fluid in the eyes or on the skin, and

injury from moving parts if you are adjusting or repair-

ing the pump.

The bleed valve shuts off the air to the pump and

relieves air trapped between this valve and the pump

after the air is shut off. Trapped air can cause the pump

to cycle unexpectedly. Locate the valve close to the

pump.

Installation

3A0096B 9

Key:

A Air Motor

B Displacement Pump

C Floor Stand

D Air Inlet

F 76 mm (3 in.) Fluid Inlet

G Fluid Outlet

H Air Regulator

J Bleed Type Master Air Valve (required)

K Air Line Drain Valve (not supplied)

L Air Filter (not supplied)

M Air Shutoff Relief Valve (for accessories, not supplied)

N Pump Bleed Valve

PWetCup

R Wet Cup Drain Fitting (if used)

T DataTrak Module (standard module shown; see Ink Pump

Packages chart on page 3 for data monitoring options)

Y Ground Wire (required, see page 7)

FIG. 2. Typical Installation, Air-Powered Pumps

ti14665a

Installation

10 3A0096B

Hydraulic-Powered Pumps

• Reference numbers and letters in parentheses in

the text refer to numbers and letters in the illustra-

tions.

•F

IG. 3, page 11, shows a typical installation of an

hydraulic-powered pump. It is only a guide. Contact

your Graco distributor for actual system designs.

• Be sure all accessories, including hydraulic lines

and fluid lines, are adequately sized and pres-

sure-rated to meet system requirements.

• Use only electrically conductive hoses. Fluid hoses

must have spring guards on both ends.

Always plug the hydraulic inlets, outlets and lines when

disconnecting them for any reason to avoid introducing

dirt and other contaminants into the system.

Be sure that your hydraulic power supply is equipped

with a suction filter to the hydraulic pump and a system

return line filter of 10 micron size. Carefully follow the

manufacturer's recommendations on reservoir and filter

cleaning and periodic changes of hydraulic fluid.

NOTE: Hydraulic fluid is exhausted from differential

hydraulic motors only on the upstroke of the operating

cycle. The oil return line must have at least twice the

flow capacity as the oil supply line. Otherwise, back

pressure on the hydraulic motor piston will slow down

the motor and the fluid displacement pump, resulting in

a loss of pump performance.

On the hydraulic oil supply line (D), install a shutoff valve

(E) to isolate the system for servicing; a fluid pressure

gauge (J) to monitor hydraulic oil pressure to the motor

and avoid overpressurizing the motor or displacement

pump; a pressure- and temperature-compensated flow

control valve (H) to prevent the motor from running too

fast; a pressure reducing valve (K) with a drain line (M)

running directly into the hydraulic return line (T); and an

accumulator (L) to reduce the hammering effect caused

by the motor reversing direction.

On the hydraulic return line (T), install a shutoff valve (S)

for isolating the motor for servicing.

NOTICE

The Hydraulic Power Supply must be kept clean at all

times to avoid damage to the motor and hydraulic

power supply.

Blow out hydraulic lines with air and flush thoroughly

before connection to the motor.

Plug hydraulic inlets, outlets, and line ends when dis-

connecting them for any reason.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Graco Wasserpumpe Handbücher

Graco

Graco Fire-Ball 300 D Series Bedienungsanleitung

Graco

Graco Dura-Flo 1100 Datenblatt

Graco

Graco RPS 2900 Bedienungsanleitung

Graco

Graco Dyna-Star 239882 Bedienungsanleitung

Graco

Graco Pack'n Play Bedienungsanleitung

Graco

Graco Mongoose Series Stücklistenhandbuch

Graco

Graco 239702 Bedienungsanleitung

Graco

Graco HYDRA-CAT FIXED RATIO Bedienungsanleitung

Graco

Graco ChemSafe 205 Bedienungsanleitung

Graco

Graco Fire-Ball D Series Bedienungsanleitung

Graco

Graco Husky 1050HP Bedienungsanleitung

Graco

Graco T2 Bedienungsanleitung

Graco

Graco Series A Bedienungsanleitung

Graco

Graco SaniForce 1590 HS Bedienungsanleitung

Graco

Graco 015.050-DP Bedienungsanleitung

Graco

Graco AGP-U100 Bedienungsanleitung

Graco

Graco Husky 2200 Gebrauchs- und Pflegehandbuch

Graco

Graco BLUE DEVIL 260000 Bedienungsanleitung

Graco

Graco Husky 715 Datenblatt

Graco

Graco Wolverine A261 Series Bedienungsanleitung

Graco

Graco 5:1 Monark 952-793 Bedienungsanleitung

Graco

Graco Husky 2200 Bedienungsanleitung

Graco

Graco E-Flo SP Bedienungsanleitung

Graco

Graco 25T818 Gebrauchs- und Pflegehandbuch

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

moyno

moyno 2000 CC Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung

STA-RITE

STA-RITE ST33APP Bedienungsanleitung