Graco G3 Series Bedienungsanleitung

3A6319A

Instructions

G3 Standard Automatic

Lubrication Pump

For dispensing of NLGI Grades #000 to #2 greases. For Professional Use Only.

Not approved for use in explosive atmospheres or hazardous locations.

5100 psi (35.1 MPa, 351.6 bar) Maximum Pump Output Pressure

5000 psi (34.4 MPA, 344.7 bar) Maximum Fill Inlet Pressure

Important Safety Instructions

Read all warnings and instructions in this

manual before using this equipment. Save

these instructions.

Conforms to ANSI/UL 73

Certified to CAN/CSA

Std. 22.2 No 68-09

3132066

24V and 110-240VAC Pumps ONLY

Part / Model Numbers

23A6319A

Part / Model Numbers

The Part Number is a six-digit unique number that is only used to order the G3 Pump. Directly related to this six digit

Part Number is the configured Graco Model Number. This configured number identifies the distinct features of a spe-

cific G3 Pump. To help you understand each component that makes up the Model Number see Understanding Your

Model Number, page 3. The tables below shows the relationship between each Part Number and its related Model

Number.

8 Liter Models

12 Liter Models

16 Liter Models

20 Liter Models

Part Model Numbers

96G500 G3-G-24NC-8LTA00-0D00L000

Part Model Numbers

96G501 G3-G-24NC-12TA00-0D00L000

Part Model Numbers

96G502 G3-G-24NC-16TA00-0D00L000

Part Model Numbers

96G503 G3-G-24NC-20TA00-0D00L000

Part / Model Numbers

3A6319A 3

Understanding the Model Number

Use the Code Sample provided below to identify each component’s location in the Model Number. The options for

each component that make up the code are provided on the lists below.

NOTE: Some pump configurations are not available. Contact Graco Customer Service or your local Graco distributor

for assistance.

G3 - G = Identifies pump as being a G3; G = Grease

G3 - A = Identifies pump as being a G3; A = Oil

Code aa: Power Source

• 24 = 24 Volts DC

Code bb: Operation Control

• NC = No Controller

Code cc: Reservoir Capacity (Liters)

• 8L = 8 Liters

• 12 = 12 Liters

• 16 = 16 Liters

• 20 = 20 Liters

Code d: Follower Plate Installed

• T = Follower Plate Installed; Tie Rods

Code e: Low Level Option

• A = Low Level No Controller

Code ff: Options

• 00 = No Options

Code g, h, i, j, k, m, n, p

NOTE: Codes g - p relate to a specific location on the

G3 pump. See FIG. 1 for these locations.

•D=DIN

• 0 = Not populated

• L = Low Level

G3 -G- NC

Code Sample: a a b b - c c d e f f - g h i j k m n p

FIG. 1

Warnings

43A6319A

Warnings

The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama-

tion point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When

these symbols appear in the body of this manual or on warning labels, refer back to these Warnings. Product-specific

hazard symbols and warnings not covered in this section may appear throughout the body of this manual where

applicable.

WARNING

SKIN INJECTION HAZARD

High-pressure fluid from dispensing device, hose leaks, or ruptured components will pierce skin. This

may look like just a cut, but it is a serious injury that can result in amputation. Get immediate surgical

treatment.

• Do not point dispensing device at anyone or at any part of the body.

• Do not put your hand over the fluid outlet.

• Do not stop or deflect leaks with your hand, body, glove, or rag.

• Follow the Pressure Relief Procedure when you stop dispensing and before cleaning, checking, or

servicing equipment.

• Tighten all fluid connections before operating the equipment.

• Check hoses and couplings daily. Replace worn or damaged parts immediately.

PRESSURIZED EQUIPMENT HAZARD

Over-pressurization can result in equipment rupture.

• A pressure relief valve is required at each pump outlet.

• Follow the Pressure Relief Procedure in this manual before servicing.

Warnings

3A6319A 5

WARNING

EQUIPMENT MISUSE HAZARD

Misuse can cause death or serious injury.

• Do not operate the unit when fatigued or under the influence of drugs or alcohol.

• Do not exceed the maximum working pressure or temperature rating of the lowest rated system

component. See Technical Specifications in all equipment manuals.

• Use fluids and solvents that are compatible with equipment wetted parts. See Technical

Specifications in all equipment manuals. Read fluid and solvent manufacturer’s warnings. For

complete information about your material, request Safety Data Sheets (SDSs) from distributor or

retailer.

• Turn off all equipment and follow the Pressure Relief Procedure when equipment is not in use.

• Check equipment daily. Repair or replace worn or damaged parts immediately with genuine

manufacturer’s replacement parts only.

• Do not alter or modify equipment. Alterations or modifications may void agency approvals and create

safety hazards.

• Make sure all equipment is rated and approved for the environment in which you are using it.

• Use equipment only for its intended purpose. Call your distributor for information.

• Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.

• Do not kink or over bend hoses or use hoses to pull equipment.

• Keep children and animals away from work area.

• Comply with all applicable safety regulations.

PLASTIC PARTS CLEANING SOLVENT HAZARD

Many cleaning solvents can degrade plastic parts and cause them to fail, which could cause serious

injury or property damage.

• Use only compatible solvents to clean plastic structural or pressure-containing parts.

•SeeTechnical Specifications in all equipment manuals for materials of construction. Consult the

solvent manufacturer for information and recommendations about compatibility.

MOVING PARTS HAZARD

Moving parts can pinch, cut or amputate fingers and other body parts.

• Keep clear of moving parts.

• Do not operate equipment with protective guards or covers removed.

• Equipment can start without warning. Before checking, moving, or servicing equipment, follow the

Pressure Relief Procedure and disconnect all power sources.

PERSONAL PROTECTIVE EQUIPMENT

Wear appropriate protective equipment when in the work area to help prevent serious injury, including

eye injury, hearing loss, inhalation of toxic fumes, and burns. Protective equipment includes but is not

limited to:

• Protective eyewear, and hearing protection.

• Respirators, protective clothing, and gloves as recommended by the fluid and solvent manufacturer.

Installation

63A6319A

Installation

Component Identification - 8 Liter Model Shown

See Parts, page 17 for expanded view.

Key:

AReservoir

B Pump Element (1 included. Can accommodate 3 total)

C Pressure Relief Valve (Not shown. Not included / required for

each outlet - Available from Graco. See Parts, page 18.)

D Zerk Inlet Fill Fitting (1 included / grease models only)

E Pump Outlet Plug (2 included)

F Volume Control Spacers (2 included. More spacers = less

output volume per stroke) (also see FIG. 9, page 12)

G Fuse (DC models only - Not included, not shown. Available

from Graco. See Parts, page 18.)

HCover

J Top Mounting Bracket

K Bottom Mounting Bracket

L Part Number / Model Number example only shown, (see

pages 3, Understanding the Model Number, for details)

M Follower Plate

N Vent Hole for Follower Plate

FIG. 2

Installation

3A6319A 7

Typical Installation

Series Progressive Divider Valve

Key

A Connected to fused power source

B Pressure relief valve (Not included; required for each out-

let - user supplied)

C Supply Hose (user supplied)

D Series progressive divider valves

E To lube points

F Proximity Switch

FIG. 3

Installation

83A6319A

Injector Installations

Key

A Connected to fused power source

B Pressure relief valve (Not included; required for each out-

let - user supplied)

C Supply Hose (user supplied)

DInjectors

E To lube points

F Pressure switch

G Vent valve (Not included / available from Graco)

H Return to reservoir

FIG. 4

Installation

3A6319A 9

Unpacking

The pump module was carefully packaged for shipment

by Graco. When the package arrives, perform the follow-

ing procedure to unpack the units:

1. Inspect the shipping box carefully for shipping

damage. Contact the carrier promptly if damage is

discovered.

2. Unseal the box and inspect the contents carefully.

There should not be any damaged parts.

3. Compare the packing slip against all items included

in the box. Any shortages or other inspection

problems should be reported immediately.

Choosing an Installation

Location

- Select a location that will adequately support

the weight of the G3 Pump and lubricant, as

well as all plumbing and electrical connections.

- Refer to the mounting hole layouts provided in

the Mounting Bracket Dimensions section of this

manual, page 21. No other installation configu-

ration should be used.

- Use designated mounting holes and provided

configurations only.

- Use the five fasteners (included) to secure the

G3 to the mounting surface. 3 fasteners are

used for the bottom bracket and 2 fasteners are

used for the top bracket.

- Adjust top mounting bracket, if necessary to

align the bracket with the mounting surface (FIG.

5).

- Insert (user supplied) spacers if there is still a

gap after adjusting the bracket.

System Wiring

Fuses

Fuse Kits are available from Graco. The following Table

identifies the correct fuse to use for your input voltage

and the corresponding Graco Kit number.

Recommendations for Using Pump in

Harsh Environments

• If using a DIN style power or alarm harness with a

right angle mating connector, make sure the con-

nector does not exit the unit in the UP direction.

• Use a corrosion preventative electrical grease on all

contacts.

NOTICE

Observe precautions for handling electrostatic sensi-

tive devices. Touch ground before handling pump.

AUTOMATIC SYSTEM ACTIVATION HAZARD

If the system is equipped with has an automatic timer

(user supplied) that activates the pump lubrication

system when power is connected or when exiting the

programming function, unexpected activation of the

system could result in serious injury, including skin

injection and amputation.

Before you install or remove the lubrication pump

from the system, disconnect and isolate all power

supplies and relieve all pressure.

FIG. 5

NOTICE

Fuses (user supplied) are required on all DC mod-

els. To avoid equipment damage:

• Never operate G3 Pump DC models without a

fuse installed.

• A fuse of the correct voltage must be installed in

line with the power entry to the system.

Input Voltage Fuse Value Graco Kit No.

24 VDC 4 A 571040

Installation

10 3A6319A

Wiring and Installation Diagrams

The following Table identifies the wiring and installation

diagrams for the cable included with the pump provided

in this manual.

Power DIN DC - 15 foot

Pin and Related Wire Color (FIG. 6)

Low Level Outputs

See Low Level Output Option, page 14 for functional

description. See Technical Specifications, page 20 for

ratings.

Pins (FIG. 7)

Pin Pin Name Color

1-VDC Black

2+VDC White

3 Not Used Not Used

4Not Used Green

FIG. 6

Pin Pin Name

1 LL N.O.

2 Not Used

3LLCOM

4 Not Used

FIG. 7

Andere Handbücher für G3 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Graco Wasserpumpe Handbücher

Graco

Graco Mini Fire-Ball 225 Bedienungsanleitung

Graco

Graco 237-004 Bedienungsanleitung

Graco

Graco Xtreme 24N976 Stücklistenhandbuch

Graco

Graco Z-Pump S1 Series Stücklistenhandbuch

Graco

Graco 244197 Bedienungsanleitung

Graco

Graco LD Series Bedienungsanleitung

Graco

Graco ChemSafe 205 Bedienungsanleitung

Graco

Graco Renegade Series Gebrauchs- und Pflegehandbuch

Graco

Graco 3A2977K Stücklistenhandbuch

Graco

Graco 970204 Datenblatt

Graco

Graco Falcon A Series Bedienungsanleitung

Graco

Graco 224-630 A Series Bedienungsanleitung

Graco

Graco 24W181 Bedienungsanleitung

Graco

Graco Mini Fire-Ball 246775 Bedienungsanleitung

Graco

Graco 231169 Bedienungsanleitung

Graco

Graco Series A Bedienungsanleitung

Graco

Graco Husky 715 Bedienungsanleitung

Graco

Graco GTP10 Series Bedienungsanleitung

Graco

Graco Dyna-Star 200:1 Bedienungsanleitung

Graco

Graco ChemSafe 515 Series Stücklistenhandbuch

Graco

Graco NXT Air Motor M02LN0 Stücklistenhandbuch

Graco

Graco 24G546 Bedienungsanleitung

Graco

Graco Husky 2200 Bedienungsanleitung

Graco

Graco Viscount I 3000 Bedienungsanleitung

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

moyno

moyno 2000 CC Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung

STA-RITE

STA-RITE ST33APP Bedienungsanleitung