Graco GlasCraft Guardian A Series Gebrauchs- und Pflegehandbuch

REPAIR AND PARTS

Guardian A- Series

Material Pumps

Important Safety Instructions

Read all warnings and instructions in

this manual. Save these instructions.

For use with non-ammable foam and polyurea.

Not for use in explosive atmospheres.

Section 1 General Information

Warnings ................................................................................................................................................................. 3

Assembly Drawings ................................................................................................................................................. 7

Sub Assembly Drawings .......................................................................................................................................... 10

Maintenance ............................................................................................................................................................ 18

Section 2 Technical & Warranty Information

Notes ......................................................................................................................................................................... 23

Graco Warranty .............................................................................................................................. 24

Technical Assistance ...................................................................................................................... 25

Table Of Contents

Warnings

The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclamation

point symbol alerts you to a general warning and the hazard symbol refers to procedure-specic risk. Refer back to these

warnings. Additional, product-specic warnings may be found throughout the body of this manual where applicable.

WARNING

ELECTRIC SHOCK HAZARD

Improper grounding, setup, or usage of the system can cause electric shock.

Turn off and disconnect power cord before servicing equipment.• Use only grounded electrical outlets.• Use only 3-wire extension cords.• Ensure ground prongs are intact on sprayer and extension cords.• Do not expose to rain. Store indoors.•

TOXIC FLUID OR FUMES HAZARD

Toxic uids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or

swallowed.

Read MSDS’s to know the specic hazards of the uids you are using.•

Store hazardous uid in approved containers, and dispose of it according to applicable guide-• lines.

Always wear impervious gloves when spraying or cleaning equipment.•

PERSONAL PROTECTIVE EQUIPMENT

You must wear appropriate protective equipment when operating, servicing, or when in the operating

area of the equipment to help protect you from serious injury, including eye injury, inhalation of toxic

fumes, burns, and hearing loss. This equipment includes but is not limited to:

Protective eyewear•

Clothing and respirator as recommended by the uid and solvent manufacturer• Gloves• Hearing protection•

SKIN INJECTION HAZARD

High-pressure uid from gun, hose leaks, or ruptured components will pierce skin. This may look like

just a cut, but it is a serious injury that can result in amputation. Get immediate surgical treatment.

Do not point gun at anyone or at any part of the body.• Do not put your hand over the spray tip.•

Do not stop or deect leaks with your hand, body, glove, or rag.• Close material shutoff valves and shutoff or disconnect air supply when not spraying.• Follow• Pressure Relief Procedure in this manual, when you stop spraying and before cleaning,

checking, or servicing equipment.

Warnings

WARNING

FIRE AND EXPLOSION HAZARD

Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help pre-

vent re and explosion:

Use equipment only in well ventilated area.• Eliminate all ignition sources; such as pilot lights, cigarettes, portable electric lamps, and plastic• drop cloths (potential static arc).

Keep work area free of debris, including solvent, rags and gasoline.•

Do not plug or unplug power cords, or turn power or light switches on or off when ammable • fumes are present.

Ground all equipment in the work area. • Use only grounded hoses.•

Hold gun rmly to side of grounded pail when triggering into pail.•

If there is static sparking or you feel a shock, • stop operation immediately. Do not use equip-

ment until you identify and correct the problem.

Keep a working re extinguisher in the work area.•

PRESSURIZED ALUMINUM PARTS HAZARD

Do not use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon

solvents or uids containing such solvents in pressurized aluminum equipment. Such

use can cause serious chemical reaction and equipment rupture, and result in death,

serious injury, and property damage.

EQUIPMENT MISUSE HAZARD

Misuse can cause death or serious injury.

Do not operate the unit when fatigued or under the inuence of drugs or alcohol.•

Do not exceed the maximum working pressure or temperature rating of the lowest rated system • component. See Technical Data in all equipment manuals.

Use uids and solvents that are compatible with equipment wetted parts. See • Technical Data in

all equipment manuals. Read uid and solvent manufacturer’s warnings. For complete informa-

tion about your material, request MSDS forms from distributor or retailer.

Check equipment daily. Repair or replace worn or damaged parts immediately with genuine • manufacturer’s replacement parts only.

Do not alter or modify equipment.• Use equipment only for its intended purpose. Call your distributor for information.•

Route hoses and cables away from trafc areas, sharp edges, moving parts, and hot surfaces.•

Do not kink or over bend hoses or use hoses to pull equipment.•

Keep children and animals away from work area.• Comply with all applicable safety regulations.•

MOVING PARTS HAZARD

Moving parts can pinch or amputate ngers and other body parts.

Keep clear of moving parts.• Do not operate equipment with protective guards or covers removed.•

Pressurized equipment can start without warning. Before checking, moving, or servicing equip-• ment, follow the Pressure Relief Procedure in this manual. Disconnect power or air supply.

BURN HAZARD

Equipment surfaces and uid that’s heated can become very hot during operation. To avoid

severe burns, do not touch hot uid or equipment. Wait until equipment/uid has cooled completely.

Isocyanate Hazard

Spraying materials containing isocyanates creates

potentially harmful mists, vapors, and atomized

particulates.

Read material manufacturer’s warnings and

material MSDS to know specic hazards and

precautions related to isocyanates.

Prevent inhalation of isocyanate mists, vapors, and

atomized particulates by providing sufcient ventila-

tion in the work area. If sufcient ventilation is not

available, a supplied-air respirator is required for

everyone in the work area.

To prevent contact with isocyanates, appropriate

personal protective equipment, including chemically

impermeable gloves, boots, aprons, and goggles, is

also required for everyone in the work area.

Material Self-Ignition

Some materials may become self-igniting if applied

too thickly. Read material manufacturer’s warnings

and material MSDS.

Moisture Sensitivity of

Isocyanates

Isocyanates (ISO) are catalysts used in two component

foam and polyurea coatings. ISO will react with moisture

(such as humidity) to form small, hard, abrasive crystals,

which become suspended in the uid. Eventually a lm will

form on the surface and the ISO will begin to gel, increas-

ing in viscosity. If used, this partially cured ISO will reduce

performance and the life of all wetted parts.

The amount of lm formation and rate of crystal-

lization varies depending on the blend of ISO,

the humidity, and the temperature.

To prevent exposing ISO to moisture:

Always use a sealed container with a desiccant dryer• in the vent, or a nitrogen atmosphere. Never store ISO

in an open container.

Keep the ISO lube pump reservoir lled with Graco • Throat Seal Liquid (TSL), Part 206995. The lubricant

creates a barrier between the ISO and the atmosphere.

Use moisture-proof hoses specically designed for • ISO, such as those supplied with your system.

Never use reclaimed solvents, which may contain•

moisture. Always keep solvent containers closed when

not in use.

Never use solvent on one side if it has been contami-• nated from the other side.

Always park pumps when you shutdown.•

Always lubricate threaded parts with Part 217374 ISO• pump oil or grease when reassembling.

Warnings

Keep Components A and B

Separate

CAUTION

To prevent cross-contamination of the equipment’s wet-

ted parts, never interchange component A (isocyanate)

and component B (resin) partrs. The gun is shipped with

the A side on the left. The uid manifold, uid hous-

ing, side seal assembly, check valve cartridge, and mix

chamber are marked on the A side.

Foam Resins with 245 fa

Blowing Agents

New foam blowing agents will froth at temperatures above

90°F (33 °C) when not under pressure, especially if agitat-

ed. To reduce frothing, minimize preheating in a circulation

system.

Changing Materials

When changing materials, ush the equipment mul-• tiple times to ensure it is thoroughly clean.

Always clean the uid inlet strainers after ushing.•

Check with your material manufacturer for chemical • compatibility.

Most materials use ISO on the A side, but some use• ISO on the B side.

Epoxies often have amines on the B (hardener) side.• Polyureas often have amines on the B (resin) side.

Warnings

Section 1 - General Information: Assembly Drawings

GC2616 Material Pump Assembly

Ref. Part Description Qty.

1* SCREW, SET, FLAT PT., 3/8-24 2

2 GC0324 EXTENSION, STANDOFF, AIR MOTOR 2

3 GC0325 PLATE, MTG, PUMP 1

4 GC0326 SADDLE, PUMP 1

5 GC0382 EXTENSION, STANDOFF, AIR MOTOR,

5 IN. 4

6 112925 SCREW, CAP, BTN HD 4

7 GC0495 FITTING, ELBOW, SW, 3/8 NPTM X 1/2

TUBE 1

8 GC0736 VALVE, 4-WAY, NO, 3/8 IN. NPTF, 24 VAC 1

9 GC0781 GUARD, SURROUND, LEFT 1

10 GC0782 GUARD, SURROUND, RIGHT 1

11 GC0805 SWITCH, PRESSURE, HIGH 2

12 GC0808 ASSY, PUMP, 1:1 2

14 GC0954 SWITCH, LIMIT, PLUNGER, ROLLER 1

15 GC1692 FITTING, ELBOW, LG, 1-1/16 X 3/4 STL 2

16 GC1737 BRACKET, MOUNTING, PUMP, A5-6000 1

17 GC1994 FITTING, ELBOW, 3/8 NPTM X 3/8 NPTF 3

18 803088 FITTING, PIPE, TEE, ST, 3/8, ZP 2

19 GC2041 WASHER, FLAT, STD 8

20 GC2047 WASHER, FLAT, STD 2

21 GC2052 WASHER, FLAT, STD 2

22 GC2086 NUT, HEX, SELF-LOCK 2

Ref. Part Description Qty.

23 GC2092 NUT, HEX, STD 2

24 GC2107 WASHER, LOCK, SPRING 2

25 GC2109 WASHER, LOCK, SPRING 6

26 GC2119 SCREW, RDHD, CS, .164-32 X 1.250 ZP 2

27 GC2135 SCREW, HEX HD, CS, .375-24 X 1 ZP 2

28 GC2158 FITTING, PIPE, BUSH, 3/8 NPTM X 1/4

NPTF 2

29 GC2173 SCREW, HXHD, CS, .500-13 X 1.250 ZP 4

30 100017 SCREW, CAP, HEX HD 4

31 GC2203 FITTING, CONNECTOR 2

32 GC2228 FITTING, PIPE, NIPPLE, 3/8 NPT X 4 1

33 GC2261 SCREW, SHDC, SS, .500-13 X 1 2

34 GC2267 MOTOR, AIR, 5 IN. 1

35 GC2323 MUFFLER, SILENCER, EXHAUST 2

36 GC0501 FITTING, CONNECTOR 2

37* HOSE, TUBING, POLYU, RED; 0.87 in.

1/4 OD, 1/8 ID 1

38* HOSE, TUBING, POLYU, BLUE; 0.87 in.

1/4 OD, 1/8 ID 1

39 GC0753 VALVE,CONTROL,2-WAY 1

40 GC0927 KIT, SWITCH, RETRACT, 500 SERIES;

includes (36-39) and 25 (2). 1

* Source locally.

39 25

See

Detail A

1828 11

19, 29

21, 20

Mounting bolts and washers

supplied with GC0808

Npt plug supplied

with valve (8) must be

installed in port marked

#2. Elbow tting (17)

must be installed in

port marked #4. 25, 6

30, 19

6, 25

21, 24,

23, 26

Red tubing supplied with

retract switch Blue tubing supplied with

retract switch

Clear tubing supplied with

retract switch

Detail A

Section 1 - General Information: Assembly Drawings

GC2617 Material Pump Assembly

Ref. Part Description Qty.

101* SCREW, SET, FLAT PT., 3/8-24 THD. 2

102 GC0324 EXTENSION, STANDOFF,AIR MOTOR 2

103 GC0325 PLATE, MTG, PUMP, UNIVERSAL 1

104 GC0326 SADDLE, PUMP 1

105 GC0382 EXTENSION, STANDOFF, AIR MOTOR,

5 IN. 4

106 112925 SCREW, CAP, BTN HD 4.

107 GC0495 FITTING, ELBOW, SW, 3/8 NPTM X 1/2

TUBE 1

108 GC0749 SCREW, SET, CPPT, .500-13 X 1.5 4

109 GC0781 GUARD, SURROUND, LEFT 1

110 GC0782 GUARD, SURROUND, RIGHT 1

111 GC0805 SWITCH, PRESSURE, HIGH 2

112 GC0808 ASSY,PUMP,1:1 2

113 GC2401 VALVE, POPPET, INLINE, 1/2NPT, NC 1

115 GC0954 SWITCH, LIMIT, PLUNGER, ROLLER 1

116 GC1692 FITTING, ELBOW, LG, 1-1/16 X 3/4 STL 2

117 GC1737 BRACKET, MOUNTING, PUMP, A5-6000 1

118 GC1995 FITTING, ELBOW, 1/2 NPTM X 1/2 NPTF 1

119 803088 FITTING, PIPE, TEE, ST, 3/8, ZP 2.

120 GC2041 WASHER, FLAT, STD 4

121 GC2047 WASHER, FLAT, STD 2

Ref. Part Description Qty.

122 GC2052 WASHER, FLAT, STD 2

123 GC2066 FITTING, PIPE, BUSHING 1

124 GC2086 NUT, HEX, SELF-LOCK 2

125 GC2092 NUT, HEX, STD 2.

126 GC2107 WASHER, LOCK, SPRING 2

127 GC2109 WASHER, LOCK, SPRING 4

128 GC2119 SCREW,RDHD,CS,.164-32X1.250ZP 2

129 GC2135 SCREW, HEX HD, CS, .375-24 X 1 2

130 GC2158 FITTING, PIPE, BUSH, 3/8 NPT(M) X 1/4

NPT(F) 2

131 GC2173 SCREW, HEX HD, CS, .500-13 X 1.250 4

132 GC2203 FITTING, CONNECTOR 2

133 GC2227 FITTING, PIPE, NIPPLE,1/2 NPT X 4 1

134 GC2261 SCREW, SHDC, SS, .500-13 X 1 2

135 GC2273 MOTOR,AIR, 6 IN. 1

136 GC2376 FITTING, ELBOW, SWIVEL 1

137 GC0501 FITTING, CONNECTOR 2

138* HOSE, TUBING, POLYU, 1/4, RED; 0.87

in. 1/4 OD, 1/8 ID 1

139* HOSE, TUBING, POLYU, 1/4, BLUE; 0.87

in. 1/4 OD, 1/8 ID 1

140 GC0928 KIT, SWITCH, RETRACT, 600 SERIES;

includes items 127 and 136-139 1

* Source locally.

Mounting bolts and washers

supplied with GC0808

122, 125

126, 128

127 101

108

117

111

120, 131

134

110

106

126

115

116

112

132

130 111

109

104

124

105

102

135

118

113

123 133

140

107

See

Detail A

119

121, 129

Red tubing (138)

supplied with retract

switch

Blue tubing (139) supplied

with retract switch

Clear tubing supplied with

retract switch

Detail A

Section 1 - General Information: Assembly Drawings

GC2618 Material Pump Assembly

GC1692

207, 224

214

205

230

217

227

212

210

203

204

221

206

202

See

Detail A

218, 228

212

211

232

215

233

240

201

208

209

216

234 231

216

219, 229

219, 226

207, 224

220, 222

223, 225

236 (Red tubing) 237 (Blue tubing)

(Clear tubing)

Detail A

Ref.

No. Part Description Qty.

201* SCREW, SET, FLAT PT., 3/8-24 2

202 GC0324 EXTENSION, STANDOFF, AIR MOTOR 2

203 GC0325 PLATE, MTG, PUMP, UNIVERSAL 1

204 GC0326 SADDLE,PUMP 1

205 GC0329 ASSY, PUMP, FLUID 2

206 GC0382 EXTENSION, STANDOFF, AIR MOTOR,

5 IN. 4

207 112925 SCREW, CAP, BTN HD 4

208 GC0495 FITTING, ELBOW, SW, 3/8 NPT(M) X

1/2 TUBE 1

209 GC0736 VALVE, 4-WAY, NO, 3/8 IN. NPT(F), 24

VAC 1

210 GC0781 GUARD, SURROUND, LEFT 1

211 GC0782 GUARD, SURROUND, RIGHT 1

212 GC0805 SWITCH, PRESSURE, HIGH 2

214 GC0954 SWITCH, LIMIT, PLUNGER, ROLLER 1

215 GC1737 BRACKET, MOUNTING, PUMP, A5-

6000 1

216 GC1994 FITTING, ELBOW, 3/8 NPT(M) X 3/8

NPT(F) 3

217 803088 FITTING, PIPE, TEE, ST, 3/8, ZP 2

218 GC2041 WASHER, FLAT, STD 8

219 GC2047 WASHER, FLAT, STD 2

220 GC2052 WASHER, FLAT, STD 2

221 GC2086 NUT, HEX, SELF-LOCK 2

Ref.

No. Part Description Qty.

222 GC2092 NUT, HEX, STD 2

223 GC2107 WASHER, LOCK, SPRING 2

224 GC2109 WASHER, LOCK, SPRING 6

225 GC2119 SCREW, RDHD, CS, .164-32 X 1.250

ZP 2

226 GC2135 SCREW,HEX HD, CS, .375-24 X 1 ZP 2

227 GC2158 FITTING, PIPE, BUSHING, 3/8 NPT(M)

X 1/4 NPT(F) 2

228 GC2173 SCREW, HEX HD, CS,.500-13-

X1.250ZP 4

229 100017 SCREW, CAP, HEX HD 4

230 GC2203 FITTING, CONNECTOR 2

231 GC2228 FITTING, PIPE, NIPPLE, 3/8 NPT X 4 1

232 GC2261 SCREW, SHDC, SS, .500-13 X 1 2

233 GC2267 MOTOR,AIR, 5 IN. 1

234 GC2323 MUFFLER, SILENCER, EXHAUST 2

236* HOSE, TUBING, POLYU, 1/4, RED;

1.083 in., 1/4 OD, 1/8 ID 1

237* HOSE, TUBING, POLYU, 1/4, BLUE;

1.083 in., 1/4 OD, 1/8 ID 1

240 GC0927 KIT, SWITCH, RETRACT, 500 SERIES;

includes 224, 236, and 237 1

* Source locally.

Npt plug supplied with

valve (209) must be

installed in port marked

#2. Elbow tting (216)

must be installed in

port marked #4.

Section 1 - General Information: Sub Assembly Drawings

GC0329 Fluid Section Assembly

308

301

315

316

322

320

309

302

310

307

305

306

302

304

313

302

311

314

325

310

326

312

306

329

318

324 303

323

327

321

319

317

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Graco Wasserpumpe Handbücher

Graco

Graco 25T818 Gebrauchs- und Pflegehandbuch

Graco

Graco Husky 205 D110 Series Bedienungsanleitung

Graco

Graco 248171 Bedienungsanleitung

Graco

Graco 24G546 Bedienungsanleitung

Graco

Graco FIRE-BALL Series Stücklistenhandbuch

Graco

Graco KING A Series Bedienungsanleitung

Graco

Graco ChemSafe 1040 Bedienungsanleitung

Graco

Graco Series A Bedienungsanleitung

Graco

Graco G-Mini 25R800 Bedienungsanleitung

Graco

Graco ChemSafe 307 Stücklistenhandbuch

Graco

Graco 257100 Bedienungsanleitung

Graco

Graco Series B Bedienungsanleitung

Graco

Graco Husky 1050e Gebrauchs- und Pflegehandbuch

Graco

Graco TRITON 3D150 Bedienungsanleitung

Graco

Graco Python XL-DA25 Series Stücklistenhandbuch

Graco

Graco Therm-O-Flow C03508 Stücklistenhandbuch

Graco

Graco Husky 1050 Series Gebrauchs- und Pflegehandbuch

Graco

Graco E-Flo Y31 Series Bedienungsanleitung

Graco

Graco Merkur A Series Stücklistenhandbuch

Graco

Graco Fire-Ball 300 Datenblatt

Graco

Graco Crown Imperial Series Datenblatt

Graco

Graco 232-105 Bedienungsanleitung

Graco

Graco Mini Fire-Ball 225 Bedienungsanleitung

Graco

Graco 198466 Bedienungsanleitung

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung

STA-RITE

STA-RITE ST33APP Bedienungsanleitung

GÜDE

GÜDE HWW 900 GC Bedienungsanleitung