Grandstream Networks GXV3672 HD Bedienungsanleitung

Grandstream Networks, Inc SIP Open Door using NVR/IPC Page 1 of 6

www.grandstream.com Last Updated: 10/2015

HOW TO CONFIGURE SIP OPEN DOOR VIA GRANDSTREAM

NVR/GVR355X AND WEATHERPROOF SERIES IP CAMERAS

Unlike plastic case indoor camera GXV3611IR_HD, the metal case outdoor IP66 weatherproof

IP cameras GXV3672, GXV3674 and GXV3610 series do not have built-in Alarm_In and

Alarm_Out interface. But when combined with Grandstream GVR355X, SIP Prox or IP-PBX, the

GVR355X’s built-in Alarm_In and Alarm_Out interface can be used to connect to related 3rd

party device like Door Bell/Intercom and Relay or Door Strike, to accomplish the SIP Open Door

function when configured with related SIP IP-PBX.

The benefit of such solution is that the GVR355X can only record all the person pressed the door

bell and door can be controlled (local or remotely) via video SIP calls, either via Grandstream IP

video hard phone like GXV3240 or GXV3275, or Grandstream GS_Wave soft phone (pending)

running on Android or iOS.

Following is the example of how to configure this feature. Recommend using latest firmware for

all related Grandstream device. The FW used in below example are:

•GVR355x FW: 1.0.1.29

•GXV3610/3672/3674: FW: 1.0.3.13

Firmware beyond the above versions are required for this feature to function properly.

GXV3672/GXV3674/GXV3610 (IP Camera) Side:

•Basic - SIP Setting:

Figure 1: IP Camera Basic Settings – SIP Configuration

Grandstream Networks, Inc SIP Open Door using NVR/IPC Page 2 of 6

www.grandstream.com Last Updated: 10/2015

Make sure configure correct SIP Proxy or IP-PBX by using either FQDN domain name or IP

address. Also fill in extension and password, save the setting and make sure the IP camera is

registered to the SIP server, as shown in Figure 1, the green “Online” status will be displayed

once the IP camera registered to the SIP Proxy or IP-PBX.

At the “Phone List for Alarm Out”, please fill in the extension of the IP video phone to receive

the Alarm_Out calls, this could be Grandstream SIP video hard phone or software phone. Make

sure the video phone is indeed registered to the SIP Server or IP-PBX.

Figure 2-1: IP Camera Basic Settings – Alarm Out Phone Number

Once click “Add”, the phone number will be added as shown in below:

Figure 2-2: IP Camera Basic Settings – Alarm Out Phone Number

In this example configureation, the IP camera with extension number 809, once Alarm_In

(sending from GVR355X via the Door Bell Operation) triggered, will make SIP phone call to

extension 806, the IP Video Phone configured to receve the Alarm_Out call to execute the open

door operation. The IP video phone could be Grandstream GXV3240/3275 hard phone, or

GS_Wave soft phone runing at Smartphone, like Android or iOS (Pending).

This finished the SIP related configuration on IP Camera side.

NOTE:

Make sure to DISABLE the Voicemail or Faxmail at SIP Proxy or IP-PBX side for the

extension that receving the Alarm_Out call. (Extension 806 in the example).

Grandstream Networks, Inc SIP Open Door using NVR/IPC Page 3 of 6

www.grandstream.com Last Updated: 10/2015

GVR355X (NVR) Side:

GVR355X has to configure the “IO Alarm Config” correctly to allow the “SIP Open Door”

feature function properly.

•

Software Configuration

GVR355X can be configured either via Local View interface or WebGUI interface.

Below example is using web interface of GVR3552, the GVR3550 is similar:

Figure 3: Open Door Configuration

•Alarm_In Port:

Slelect “Input Port” from pull-down selelction, this port has to be connected to the wire

connecting to the Door Bell or Intercom circuit.

•Alarm_Out Configuration:

Select “Open Door Request” to enable “Open Door” feature.

Once selected, the system will automatically enable the Alarm Input port just chosen.

Select the related IP Camera from the “Authenticaton Camera” pull-down selection (Camera 2 or

Channel 2 in this example), also select related “Open Door Port” from the pull-down selecton.

(Alarm_Out port 2 in this example).

Make sure the related Open Door Port has physical connection or circuit to the door strike.

Fill in correctly the digit key to open door, and the Alarm Duration which is the timer the

Alarm_Out port will send signal to relay to restore the state (10 seconds in the example).

NOTE:

Enter “#” key following the digits key to execute the operation.

Grandstream Networks, Inc SIP Open Door using NVR/IPC Page 4 of 6

www.grandstream.com Last Updated: 10/2015

•

Hardware Wiring

Below are illustration of wiring diagram for the GVR355X.

Figure 4: Alarm_In and Alarm_Out Connection Circuit Sample for GVR355X

NOTE:

The Alarm_In and Alarm_Out circuit connection has to be similar to above circuit

diagram and meet following requirement:

Alarm Input

Vin<15V, PINs (1.02KΩ)

Alarm Output

125VAC/0.5A, 30VDC/2A, Normal Open, PINs

The Alarm_In circuit (like above photocoupler), if there is any voltage change smaller

than 15V, as specification listed), the GVR355X Alarm_In port will detect it and trigger

the action and event

The minimum duration is 500ms for the Alarm_In to trigger and the minimum voltage

change should be bigger than 3V.

Higher voltage and wrong polarity connection are prohibited because this will damage

the devices. So please wiring correctly and do NOT connect the polarity wrong.

Any Door Bell circuit should be able to connected as Alarm_In, just make sure the

polarity connected correctly and make sure the voltage change meets the requirement.

Grandstream Networks, Inc SIP Open Door using NVR/IPC Page 5 of 6

www.grandstream.com Last Updated: 10/2015

Figure 5: Alarm_In andd Alarm_Out Wiring Diagram for GVR355X

NOTE:

Alarm_In will share the “G” as Ground, make sure to connect the “Negative” or “-“ cable

into the interface marked with “G”.

Alarm_Out port marked with A, B, please make sure to connect “Positive” or “+” cable

into the port with “A”, the “Negative” or “-“ cable into the port with “B”. (In the

example, Port 2 configured as Alarm_Out operation to Open Door, see the cable

connected into the GVR3552).

Alarm_Out duration in the above example is configured as “10 seconds” at the

GVR355X. So the Alarm_Out will act for 10 seconds before revert back to previous

state. In the example, the default is circuit “Open”, when Alarm_Out triggered, the circuit

state changed to “Close”, as illustrated below for 10 seconds and then switch back to

prevoius “Open” state.

If connecting to a multimeter, you will see the Ohm changed from unlimited to serveral

hundred Ohms during the Alarm_Out port action. See below Figure 8.

Also a “click” audiable relay switching sound can be heard if closing enough to the

GVR355X when the inside circuit doing the job.

Grandstream Networks, Inc SIP Open Door using NVR/IPC Page 6 of 6

www.grandstream.com Last Updated: 10/2015

Figure 6: GVR355X Alarm_Out Circuit Measurement

Please contact Grandstream technical support if followed the above instructions but the

feature still not working as expected. Please make sure the SIP Proxy or IP-PBX indeed

have the related IP Camera and IP Video Phone registered.

Andere Handbücher für GXV3672 HD

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Grandstream Networks Gegensprechanlage Handbücher

Grandstream Networks

Grandstream Networks GDS3710 Bedienungsanleitung

Grandstream Networks

Grandstream Networks GDS3710 Bedienungsanleitung

Grandstream Networks

Grandstream Networks GSC3510 Bedienungsanleitung

Grandstream Networks

Grandstream Networks GDS3710 Bedienungsanleitung

Grandstream Networks

Grandstream Networks GSC35 Series Bedienungsanleitung

Grandstream Networks

Grandstream Networks GDS3710 Bedienungsanleitung

Grandstream Networks

Grandstream Networks GDS3710 Bedienungsanleitung

Grandstream Networks

Grandstream Networks GSC35 Series Bedienungsanleitung

Grandstream Networks

Grandstream Networks GDS3710 Bedienungsanleitung

Grandstream Networks

Grandstream Networks GSC3570 Bedienungsanleitung

Grandstream Networks

Grandstream Networks GDS3710V2 Bedienungsanleitung

Grandstream Networks

Grandstream Networks GSC3570 Bedienungsanleitung

Grandstream Networks

Grandstream Networks GDS3710 Bedienungsanleitung

Grandstream Networks

Grandstream Networks GDS3710 Bedienungsanleitung

Grandstream Networks

Grandstream Networks GDS3710 Bedienungsanleitung

Grandstream Networks

Grandstream Networks GDS3710 Bedienungsanleitung

Grandstream Networks

Grandstream Networks GDS3710 Bedienungsanleitung

Grandstream Networks

Grandstream Networks GDS3710 Bedienungsanleitung

Grandstream Networks

Grandstream Networks GDS370 Series Bedienungsanleitung

Grandstream Networks

Grandstream Networks GDS3710 Bedienungsanleitung

Grandstream Networks

Grandstream Networks GDS3710 Bedienungsanleitung

Grandstream Networks

Grandstream Networks GDS3712 Bedienungsanleitung

Grandstream Networks

Grandstream Networks GDS3710 Bedienungsanleitung

Grandstream Networks

Grandstream Networks GDS3705 Bedienungsanleitung

Beliebte Gegensprechanlage Handbücher anderer Marken

Bticino

Bticino LINEA 3000 Bedienungsanleitung

MSI

MSI MSI-140 Bedienungsanleitung

golmar

golmar Stadio Plus Bedienungsanleitung

CyberData

CyberData 011211 series Handbuch

Vidos

Vidos duo M1021 Bedienungsanleitung

Vimar

Vimar ELVOX 7539/E Bedienungsanleitung

SSS Siedle

SSS Siedle BTSV 850-03 Bedienungsanleitung

Dahua

Dahua VTO Series Bedienungsanleitung

Elvox

Elvox 5651 Bedienungsanleitung

Videx

Videx VIDEOKIT Series Bedienungsanleitung

Rocom

Rocom Doortello Business FW T2.05W2.04 Bedienungsanleitung

Viking

Viking E-35-EWP Bedienungsanleitung

Safeguard Supply

Safeguard Supply LRA-EX1000 Bedienungsanleitung

SSS Siedle

SSS Siedle BFCV 850 Series Bedienungsanleitung

GRD

GRD MAX V2 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Aiphone

Aiphone IE-8MD Bedienungsanleitung

Perel

Perel EDB4 Bedienungsanleitung