Graphic Whizard PT 331S Bedienungsanleitung

PT 331S

Creaser/Perforator

Operator’s Manual

Toll Free: 1-800- 265-3376 Tel: (905) 633-7663 Fax: (905) 637-4419

WWW.GRAPHICWHIZARD.COM

 
 2 
2020-10-20 
Table of Contents 
 
Introduction........................................................................................................3 
Safety.................................................................................................................4 
Specifications.....................................................................................................5 
Overview............................................................................................................6 
Keypad........................................................................................................7 
Set Up................................................................................................................8 
Output Tray, Stops and Guides...................................................................8 
Feed Table Extension.................................................................................8 
Power Socket and Switch ...........................................................................9 
Quick Start.......................................................................................................10
Programming a Crease Job......................................................................10 
Screen Operation.............................................................................................11
Welcome Screen.......................................................................................11
Ready Screen ...........................................................................................11 
Crease Data Screen..................................................................................12 
Cover Hinge Screen..................................................................................13
Progressive Screen...................................................................................14
Saving Jobs Screen..................................................................................16 
Recalling Jobs Screen ..............................................................................16 
Speed Screen ...........................................................................................17
Recalibration Screen.................................................................................17
Hardware Setting.............................................................................................18
Skew Adjustment ......................................................................................18 
Crease Depth............................................................................................18
Adjusting the Crease Depth...............................................................19
Slide-in Tools...................................................................................................20 
Installing the Tools:...................................................................................20
Perf Crash Pad .........................................................................................21
Replacing the Crash Pad...................................................................21 
Optional Parts..................................................................................................22 
Perforating Wheel .....................................................................................22
Trouble Shooting..............................................................................................25
C-1 Top Cover Open.................................................................................25
C-2 Paper Jam at Infeed Roller.................................................................26
C-3 Paper Jam at Outfeed Roller..............................................................27
E-1 Crease Motor Error.............................................................................28
Maintenance ....................................................................................................29 
 
 

Introduction

The PT 331S is an entry level creaser gives the same professional results of

more expensive creasers at a fraction of the cost. Interchangeable crease/perf dies

allow operators to switch from high quality creasing to perforating in seconds.

Before using the PT 331S please read this instruction manual carefully. Keep the

manual nearby for easy access. For any questions or concerns regarding this PT

331S please consult your local dealer.

While every effort was made at time of publication to ensure accuracy, Graphic

Whizard will not be liable for omissions or errors. Due to continued improvements

in this product line specifications and information are subject to change without

notice. Actual results are dependent upon application. Paper stock, print engine

used, and environmental conditions will affect results.

Safety

•Ensure to power down the PT 331S before performing maintenance.

•In order to avoid mistakes when reconnecting wires, mark the connectors

before disconnecting.

•Ensure the connectors are secure before restoring power to the unit.

•Read and understand this manual before powering on the machine.

•Check the plug and machine voltage frequency of your main supply for

correct output and ground.

•Use a power cord rated no less than 15A.

•Connect the machine to a 15A power outlet at 110V.

•Ensure all safety covers are in place before operating. The top covers have

a safety interlock that will disable the unit if removed.

•Open and close the covers slowly.

•Disconnect power before cleaning or accessing the inside of the machine.

•Disconnect power if the unit will not be used for an extended length of time.

•Ensure the machine is installed on a level surface.

•Do not use or unplug the unit with wet hands.

•Do not place any liquid receptacles on the machine.

•Tie back long hair and loose clothing before using the machine.

•Do not place your fingers in the creasing nip unit while the machine is

operating.

•Keep machine clear of items and debris.

•Do not alter or install anything without authorization from Graphic Whizard.

•Do not touch any running parts.

•Do not power off the machine while running.

•Keep heavy material off machine.

Keep metals and flammable materials away from the machine. Failure to do

so may cause shock or fire. In such an event, power down the unit if it is safe to do

so, then disconnect the power. If the machine overheats, smokes or an odor is

detected, immediately shut down the unit and remove the power cord. Contact your

dealer certified technician.

Specifications

Dimensions (W*L*H)

20” x 43.3” x 14.9”

510 x 1100 x 380mm (fully assembled)

Weight

104 lbs / 47kg

Creasing Paper Thickness

100-350 gsm (0.1~0.35mm)

Perforating Paper Thickness

100-250 gsm (0.1~0.25mm)

Paper Length

35.4”

Paper Width

12.9”

Speed

35~42 sheets/min (manual feed)

Minimum Crease Gap

crease: 1mm

perforating: 10mm

Minimum Gap from Leading Edge to

First Crease

crease: 1mm

perforating: 10mm

Crease Accuracy

±0.3mm

Crease Quantity in One Pass

0 - 32

Maximum Program Quantity

Crease Counting

reversible counter

Total Sheet Counter

for crease quantity and paper quantity

Skew Adjustment

standard

Crease Depth Adjustment

standard

Feeding Extension Table

standard

Output Tray

standard

Linear Perforating

optional

Linear Scoring

optional

Stand

optional

Power

110v / 60Hz / 15A

Fuse Rating

3.15A

Overview

Power Socket

System power cord

Power Switch

On/off

Tools Storage

For crease die or perforating die

Extension Table

For longer sheets

Magnetic Side Guide

Flexible guides for paper feeding

Fixed Side Guide

For skew adjustment

Safety Switch

Alerts when safety cover is open or closed

Depth Setting Screw

For crease depth adjustment

Output Roller

For mounting linear tools and sheet output

10.

Control Panel

Input data

11.

Safety Cover

Covers crease area with interlock switch

12.

LCD Screen

Display settings

13.

Output Tray

For stacking finished sheets

14.

Side Cover

For inserting/removing the crease/perf dies

Keypad

Key

Description

Stop

Stop the machine

Start

Run the machine

Test

Machine will stop after one sheet

Clear

Clear the data or clear the error display

Numbers

Input data

Scroll

Turn the page

Indicator- No Paper

“C-4 No Paperor Infeed Jam” no paper or jam detected

Indicator-Motor Error

“E-1 CR Motor Error” crease motor locks

Indicator-Paper

Jammed

“C-2 Jam at Infeed” or “C-3 Jam at Outfeed” paper is

jammed inside the machine

10.

Indicator-Safety

Cover

“C-1 CR Cover Open” safety cover is open or ajar

11.

Forward/Reverse

Press arrows to move rollers when paper jams

12.

Mode

Change the mode settings

13.

Screen

Displays data information.

14.

Enter

After data input, press Enter to confirm

Set Up

Output Tray, Stops and Guides

Set the guides and stops according to the paper format. Due to the manual feed

operation, the capacity of the tray is less than 1.1” / 30mm.

Feed Table Extension

•Locate the 3 screws on the edge of feeding table.

•Line up the screws with the 3 holes on the edge of extension table.

•Loosen, but not remove the screws.

•Connect extension table with each screw head through a hole.

•Tighten the 3 screws.

Power Socket and Switch

The power socket and switch are both on the operator side of the unit. Before

operation, please connect the power cord to the socket and press the power switch

(when the circle is down, the machine is powered off).

There is a 3.15A fuse under the socket to protect the unit from overload. To replace

the fuse, remove the cartridge with a straight screwdriver. Then remove the broken

fuse from the cartridge and load a new one. Re-insert the cartridge into the socket.

Quick Start

Programming a Crease Job

Turn on machine. Screen 1 will appear after the welcome page.

Screen 1 Screen2

Press Mbutton once, the screen will change to Screen 2 and line [1] will flash.

Enter line [1] value, 3 (3.0). Press Enter, line [2] will flash.

Enter line [2] value, 6 (6.0). Press Enter, screen change to Screen 3, line [3] will

flash.

Screen 3 Screen 4

Enter line [3] value 9 (9.0). Press Enter, line [4] will flash.

Press Enter when line [4] is 0, screen will change to Screen 4

Press RUN to feed a sheet. Paper is creased at 3”, 6”, 9” (crease line distance

from the leading edge).

Press STOP if you want to stop the job.

Inhaltsverzeichnis

Andere Graphic Whizard Büroausstattung Handbücher

Graphic Whizard

Graphic Whizard PT 331SCC Bedienungsanleitung

Beliebte Büroausstattung Handbücher anderer Marken

silen

silen Space 2 Bedienungsanleitung

Middle Atlantic Products

Middle Atlantic Products LD Series Bedienungsanleitung

SHFL

SHFL DECK MATE BLACKJACK Bedienungsanleitung

DROMEAS

DROMEAS LINE Bedienungsanleitung

Siemens

Siemens HIPATH 2000 Bedienungsanleitung

VITRA

VITRA Stefan Hürlemann Dancing Wall Bedienungsanleitung

BISLEY

BISLEY Glide V2 Bedienungsanleitung

fully

fully Haven Bedienungsanleitung

Plus

Plus NF-20 Bedienungsanleitung

OCEE DESIGN

OCEE DESIGN SASS-0100 Bedienungsanleitung

NanaWall

NanaWall CSW75 Bedienungsanleitung

Vivo

Vivo DESK V000C Bedienungsanleitung

ABB

ABB 2TKA002145G1 Bedienungsanleitung

PolyVision

PolyVision Flow Bedienungsanleitung

MBM

MBM FC-10 Bedienungsanleitung

Wiremold

Wiremold V2400 Series Bedienungsanleitung

Vivo

Vivo PP-3-T072D Bedienungsanleitung

BuzziSpace

BuzziSpace BuzziNest Booth Bedienungsanleitung