GRAUPNER ULTRAMAT AC/DC EQ Bedienungsanleitung

OPERATING INSTRUCTION

Prior to use, please read this manual thoroughly.

Keep this manual in a convenient place for quick and easy reference.

ULTRAMAT

AC/DC EQ

ULTRAMAT AC/DC EQ

BEFORE USE

SUPPROT AND SERVICE

Customer support

Internet sales site

A/S regulation

Warranty regulation

OPENHOBBY A/S CENTER

SAFETY PRECAUTIONS

BOX CONTENTS

SPECIFICATION

FEATURES

CHARGER CONTROL IDENTIFICATION

POWER SOURCE

BATTERY CONNECTION

BATTERY TYPE SELECTION

MEMORY SETUP

NiCd, NiMH BATTERIES CHARGE/DISCHARGE

NiCd, NiMH charge

NiCd, NiMH discharge

NiCd, NiMH cycle

LiPo, LiIon, LiFe BATTERIES CHARGE/DISCHARGE

LiPo charge

LiPo discharge

LiPo cycle

LiPo store

LiPo balancer

Pb CHARGE/DISCHARGE

Pb charge

Pb discharge

DISPLAYS DURING CHARGE/DISCHARGE

ERROR MESSAGES

BATTERY CHARGE TIME CALCULATION

NEW BATTERY CHARGE

Pb BATTERY SAFETY

LiIon, LiPo, LiFe BATTREIES SAFETY

ENVIRONMENT PROTECTION NOTES

SAFETY APPROVAL

8~9P

9~10P

10P

10~11P

11P

12P

13P

13~14P

14P

14~15P

14P

15P

15~16P

16~17P

17P

18P

18~19P

19P

Contents

ULTRAMAT AC/DC EQ

◎ BEFORE USE

◎ SUPPORT AND SERVICE

◎ OPENHOBBY A/S CENTER

Thank you for purchasing ULTRAMAT AC/DC EQ charger.

This system is extremely versatile and may be used by beginners and pros alike. In

order for you to make the best use of your system, please read this manual carefully. If

you have any difculties while using your system, please consult the manual, our online

Frequently Asked Questions (on the web pages referenced below), your hobby dealer, or

the Graupner/SJ Service Center.

Due to unforeseen changes in production procedures, the information contained in this

manual is subject to change without notice.

8F, 202 Dong, Chunui Techno-Park II, 18, 198 street, Bucheon-ro, Wonmi-Gu,

Bucheon-Shi, Gyungki-Do KOREA 420-857

Phone: 82-070-7863-3675 Fax: 82-070-7863-3670

Customer Service E-mail: service@openhobby.com

Internet sales site

Warranty regulation

Refer the WARRANTY CARD in a Package.

Customer support

Please feel free to ask any question by e-mail or phone. We’ve been trying to deal

with your question. We are open from nine to six, Monday to Friday in Korea. We may

respond to your question by e-mail as soon as possible when we are close.

A/S regulation

Only when the product is faulty after normal operation within the warranty period, we

will repair the product for free based on our regulations. The repair will be paid for by

the consumer when the damage is due to use in improper ways or beyond the warranty

period.

Please feel free to contact “www.openhobbby.com” to get all information on

product features, specications, running events and the newest product line up.

ULTRAMAT AC/DC EQ

◎ ◎◎ ◎◎◎

◎ BOX CONTENTS

◎ SAFETY PRECAUTIONS

1. Do not attempt to charge incompatible types of rechargeable batteries. This charger is

designed to only charge and discharge Nickel Cadmium, Nickel Metal Hydride, Lithium

Ion, Lithium Polymer, and Lead Acid batteries.

2. Do not attempt to charge a dead or damaged battery.

3. 12V input from Pb battery or reliable 12V power supplier that can supply more than 7A

current is needed

4. Make sure to place the charger on a rm level surface for charging.

5. Do not attempt to charge batteries at excessive fast charge currents. Check with your

battery manufacturer for the maximum charge rate applicable to your battery.

6. Do not allow water, moisture or foreign objects into the charger and use in a well venti-

lated area

7. Do not place the battery or charger on or near a ammable object while in use. Keep

away from carpets, cluttered workbenches, etc.

8. Do not leave the charger unattended while charging. Disconnect the battery and remove

input power from charger immediately if the charger becomes hot and keep the charger

and battery cool down before reconnecting. Young children should be supervised to

ensure that they use the appliance safely

9. Do not disassemble the charger.

10. If lead-acid battery is used to charge battery, the battery terminal shouldn’t be contact-

ed to the chassis

11. Do not use automotive type battery chargers to power the charger.

12. Do not cover the air intake holes on the charger as this could cause the charger to

overheat.

13. Connect the input leads to a 12V power supply rst, then connect the battery.

14. Do not attempt to charge non-rechargeable batteries.

15. Please comply with LiIon, LiPo, LiFe safety before charging

16. Do not use the damaged AC Power cord.

1. Charger 1EA

2. AC Power cord 1EA

3. Balance board 1EA

4. Balance cable 1EA

5. Charge cable 1set (RED/BK)

ULTRAMAT AC/DC EQ

1. Built in micro processor controls charge/ discharge, storage, balance system

2. NiCd, NiMH, LiIon, LiPo, LiFe, Pb batteries are available. Max 80W charge

3. NiCd and NiMH: Delta peak detection system, Lithium and Pb: Voltage detection

system

4. 2-line, 16 black & white backlit character LCD

5. Selectable 3.6V or 3.7V or 3.3V, 1~6 cells LiIon battery

6. Support 0.1A~7.0A charge current, NiCd / NiMH 1-14cells, 1.2-16.8V

7. Support 10~1000mA discharge current, NiCd / NiMH 1-14cells, 1.2-16.8V

8. Support cycle mode (Charge to discharge / Discharge to charge).

9. Prevent form reverse connecting of Input, output terminal. Built in cell balancer

10. Built in DC 12V, 5.0A power supplier, 110-220V AC input.

◎ SPECIFICATION

◎ FEATURES

11.0-15.0V DC or AC 100V ~ 240V / 50 ~ 60Hz

NiCd 1-14 cells / NiMH 1-14cells

LiIon 1-6 cells/LiPO 1-6 cells, LiFe 1-6 cells (Type:3.6V or 3.7V or 3.3V )

Pb Batt 1-6 cells ( 2V per cell )

100mAh ~ 9900mAh NiCd NiMH

100mAh ~ 50000mAh adjustable ONLY for LiIon, LiPo and LiFe

0.1A ~ 7A in 100mA steps (DC:80W, AC : 50W)

0.1A ~ 1A in 100mA steps (auto limited to 5W maximum)

0 ~ 200mA

Max. 280mA

“zero delta V” peak detection for NiCd/NiMH

“constant current / constant voltage”for LiIon/ LiPo/ LiFe and Pb

3mV ~ 25mV for NiCd & NiMH batteries per cell

Charge to Discharge / Discharge to Charge

2-line, 16 black&white backlit character LCD

160 x 152 x 69 mm / 6.30 x 5.98 x 2.72 in

684 g / 24.13 oz

Input Voltage

Battery Type & Cells

Battery Capacity

Charge Current

Discharge Current

Trickle Charge Current

Balancing Current

Charge Termination

Cycling

Delta Peak Sensitivity

Display Type

Dimensions

Weight

Memory

ULTRAMAT AC/DC EQ

1. Connect charger to 12V DC power supply or AC110-220V

2. Connect the charger’s red alligator clip to the positive (+) terminal on the power source

and the black alligator clip to the negative (-) terminal. In case of DV 12V input, charg-

er will display “INPUT BATTERY VLOTAGE ERROR” message if the input is below

11V or above 15V. In this case, please recheck the input power supply to make sure

adequate power is present.

If AC power is being used as input power, do NOT try to connect the 12V DC power!

◎ CHARGER CONTROL IDENTIFICATION

◎ POWER SOURCE

2-line, 16 character LCD

AC Input

- Output

AC lnput

- Output

+ Output

Balancer port

Balancing port

Buttons

ULTRAMAT AC/DC EQ

Nixx

LiFe

LiPo

Lilon

Lithium batteries need to balance for more safety, if lithium batteries are charged

without balance board, the balancing of lithium batteries is not performed.

◎ BATTERY TYPE SELECTION

◎ BATTERY CONNECTION

Connect charge cable to 4mm output banana sockets on charger with attention to polarity,

red +, black –. If battery is not connected to charger correctly, the error message is ap-

peared

- No battery : When a battery is not connected to the charger’s output

- Open circuit : When a battery becomes disconnected during an operation

- Reverse polarity : When a battery is connected to the output in reverse

When the power supplier is connected to the charger the below screen is displayed and

the Setup screen is displayed after about 1 second

Press BATT TYPE button twice to select Battery type

※ The programming setup is applied differently when you press START/STOP button less

than 1 Sec and longer than 1 Sec

Press ENTER button then battery type blinks and press ENTER button again then

other value blinks. If you leave it for more than 3 sec without operating, the blinking is

stopped. Press and hold ENTER button to start charge or discharge.

Pole

LiPo

Ultramat AD EQ

Graupner/SJ 1.00

Pole

Nixx

Pole

LiPo

Pole

LiFe

Pole

Lilo

Pole

12V

[01]

800

[01]

3000

[01]

3000

[01]

3000

[01]

3000

[01]

pack

CAUTION

ULTRAMAT AC/DC EQ

◎ MEMORY SETUP

ULTRAMAT AC/

DC EQ has 10 memories

It is used to store specic battery, charge, discharge and safety parameters, as well as

being used to initiate charging, discharging, cycling/store mode functions

① Press ENTER button then the memory number blinks. Press INC/DEC buttons to select

the memory number.

② Press ENTER button then BATTERY TYPE blinks. Press INC/DEC buttons to select

battery type.

④ Press ENTER button and INC/DEC buttons to set battery capacity.

③ Press ENTER button then battery cell blinks. Press INC/DEC buttons to set battery cell.

⑤ Press ENTER button to remove the curser blinking.

⑥ Press INC/DEC buttons to set charge current and charge voltage and then press EN-

TER button to remove the curser blinking.

⑦ Press INC button to access to DISCHARGE mode and press INC/DEC buttons to set

discharge current and discharge voltage and then press ENTER button to remove the

curser blinking.

Pole

LiPo

Pole

LiPo

Pole

LiPo

Pole

LiPo

Pole

LiPo

C=3.0A

[01]

3000

[01]

3000

[01]

3000

[01]

3000

[01]

3000

CHARGE

4.2V/C

LiPo

D=1.0A

DISCHARGE

3.0V/C

ULTRAMAT AC/DC EQ

- NiCd, NiMH charge

① Go to Nixx mode

② Press INC button to access to CHARGE mode

③ Press ENTER button shortly then the value of charge current blinks, press DEC/INC

buttons to set the desired value of charge current.

④ Press ENTER button then the value of delta peak blinks, press DEC/INC buttons to

set the desired value of delta peak.

⑤ Press and hold ENTER button to start charge battery.

⑧ Press INC button to access to CYCLE mode and press INC/DEC button to charge/dis-

charge sequence and repeating number and then press ENTER button to remove the

curser blinking.

⑨ Press INC button to access STORE mode and press INC/DEC buttons to set charge/

discharge and then press ENTER button to remove the curser blinking.

⑩ Press INC button to access to BLANCER mode and check if the setup is correct.

◎ NiCd, NiMH BATTERIES CHARGE/DISCHARGE

LiPo

C=3.0A

LiPo

C=3.0A

LiPo

(03)CELL

CYCLE D->C1

D=1.0A

STORE

D=1.0A

BALANCER

START

Prole

Nixx 5S

Nixx

C=3.0A

Nixx

C=3.0A

Nixx

C=3.0A

[01]

3000

CHARGE

d=25mV/c

CHARGE

d=25mV/c

CHARGE

d=25mV/c

BATTERY

PLEASE

CHECK

WAIT....

ULTRAMAT AC/DC EQ

- NiCd, NiMH cycle

① Go to Nixx mode

② Press INC button 3 times to access to CYCLE mode

③ Press ENTER button shortly then the cycle sequence blinks, press DEC/INC buttons

to set the desired cycle sequence

④ Press ENTER button then the number of cycle blinks, press DEC/INC buttons to set

the desired number of cycle

※ D->C : Discharge to Charge/ C->D : Charge to Discharge

- NiCd, NiMH discharge

① Go to Nixx mode

② Press INC button twice to access to DISCHARGE mode

③ Press ENTER button shortly then the value of discharge current blinks, press DEC/

INC buttons to set the desired value of discharge current

④ Press ENTER button then the value of discharge cutoff voltage blinks, press DEC/

INC buttons to set the desired value of discharge cutoff voltage

※ We recommend battery cells x 0.9V as the discharge cutoff voltage

⑤ Press and hold ENTER button to start discharge battery

Prole

Nixx

D=1.0A

Nixx

D=1.0A

Nixx

D=1.0A

BATTERY

PLEASE

Prole

Nixx

C=3.0A

Nixx

C=3.0A

[01]

3000

DISCHARGE

0.8V/C

DISCHARGE

0.8V/C

DISCHARGE

0.8V/C

CHECK

WAIT....

[01]

3000

CYCLE C->D1

D=1.0A

CYCLE C->D1

D=1.0A

Nixx

C=3.0A

CYCLE C->D1

D=1.0A

Inhaltsverzeichnis

Andere GRAUPNER Akkuladegerät Handbücher

GRAUPNER

GRAUPNER ULTRAMAT 10 Bedienungsanleitung

GRAUPNER

GRAUPNER Polaron EX Bedienungsanleitung

GRAUPNER

GRAUPNER 6475 Bedienungsanleitung

GRAUPNER

GRAUPNER ULTRAMAT 25 Bedienungsanleitung

GRAUPNER

GRAUPNER TURBOMAT 4 Bedienungsanleitung

GRAUPNER

GRAUPNER ULTRA DUO PLUS 60 Bedienungsanleitung

GRAUPNER

GRAUPNER POLARON AC/DC SPORTS Bedienungsanleitung

GRAUPNER

GRAUPNER POLARON EX-1400 Bedienungsanleitung

GRAUPNER

GRAUPNER ultra duo plus 80 Bedienungsanleitung

GRAUPNER

GRAUPNER Polaron EX Bedienungsanleitung

GRAUPNER

GRAUPNER ULTRA DUO PLUS 30 Bedienungsanleitung

GRAUPNER

GRAUPNER 6444 Bedienungsanleitung

GRAUPNER

GRAUPNER ULTRA TRIO PLUS 14 Bedienungsanleitung

GRAUPNER

GRAUPNER ULTRAMAT 8 Bedienungsanleitung

GRAUPNER

GRAUPNER ULTRAMAT 12 Bedienungsanleitung

GRAUPNER

GRAUPNER MULTILADER 3 Bedienungsanleitung

GRAUPNER

GRAUPNER ULTRAMAT 12 PLUS POCKET Bedienungsanleitung

GRAUPNER

GRAUPNER MULTILADER 7E Bedienungsanleitung

GRAUPNER

GRAUPNER LIPO-QUICK-CHARGER 4 Bedienungsanleitung

GRAUPNER

GRAUPNER S2007 Ultra DC Quad Bedienungsanleitung

GRAUPNER

GRAUPNER POLARON EX-1400 Bedienungsanleitung

GRAUPNER

GRAUPNER Polaron Bedienungsanleitung

GRAUPNER

GRAUPNER PB AUTOMATIKLADER Bedienungsanleitung

GRAUPNER

GRAUPNER ULTRA DUO PLUS 60 Bedienungsanleitung

Beliebte Akkuladegerät Handbücher anderer Marken

AA Portable Power Corp

AA Portable Power Corp Universal Smart Charger Bedienungsanleitung

Enelion

Enelion Vertica Bedienungsanleitung

RCA

RCA CHU6 Bedienungsanleitung

ANSMANN

ANSMANN ALCT 6/24-10 Bedienungsanleitung

Hitachi

Hitachi UC 18YRSL Fehlerbehebungshandbuch

Olympus

Olympus B-20 LPC Bedienungsanleitung

Exibel

Exibel ZH1708143 Bedienungsanleitung

Lenmar

Lenmar Mach 1 Bedienungsanleitung

CTEK

CTEK MXS 5.0 Bedienungsanleitung

ABB

ABB HT842379 Bedienungsanleitung

Nitecore

Nitecore Superb Charger SC4 Bedienungsanleitung

Renogy

Renogy RBC2125DS-21W Bedienungsanleitung

Braun

Braun BWC02M Bedienungsanleitung

CTEK

CTEK MXS 3.6 Bedienungsanleitung

Black & Decker

Black & Decker BDV090 Bedienungsanleitung

Trinity

Trinity DPD Bedienungsanleitung

Hulkman

Hulkman Sigma 1 Bedienungsanleitung

IKEA

IKEA koppla Bedienungsanleitung