GREAT PLAINS HP-100 Dual-Flo Bedienungsanleitung

The GPI HP-100 DUAL-FLO

Petroleum Hand Pump is de-

signed to manually pump petroleum products compatible

with aluminum and Buna-N. The user has the flexibility of

operating the pump at two flow rates. A setting of 1/2-gallon

provides faster high-capacity flow. A 1/4-gallon setting al-

lows for easier pumping of fluids. The HP-100 Hand Pump is

designed for use on a tank with a 2-inch bung.

Read Me!

Observe standard precautions when handling fuel.

•Keep fuel away from open flame or spark.

•Do not refuel vehicles or equipment with engines running

or while equipment engine is hot.

•Do not smoke while refueling.

Use the HP-100 Hand Pump only with petroleum products

such as diesel fuel, kerosene, and gasoline. This equipment

should not be used to pump chemicals.

Damage Inspection

Upon receipt of your pump system, carefully inspect visible

components for any damage that may have occurred during

shipping. Note that the pump includes a suction pipe, dis-

charge hose, and nozzle. If any parts are damaged or

missing, please contact your distributor.

GENERAL INFORMATION

HP-100 Dual-Flo

Petroleum Hand Pump

Owner’s Manual

Use the following procedures to install the HP-100 Hand

Pump on a tank with a 2-inch bung.

Install Suction Pipe

1. Remove the two protective plugs from the pump inlet and

outlet ports.

2. Wrap the threaded end of the suction pipe with 3 to 4 turns

of Teflon

tape.

3. Insert the suction screen into the inlet cover.

4. Place the spacer in the inlet cover to secure the inlet screen.

5. Install the suction pipe into the inlet cover and tighten

firmly with a pipe wrench.

INSTALLATION

5252 East 36th Street North

Wichita, KS USA 67220-3205

TEL: 316-686-7361

FAX: 316-686-6746

“A Great Plains Ventures Subsidiary”

www.gpi.net

1-800-835-0113

Rev. - 921407-0911/02

Figure 1

Install Pump on Tank

1. Before installing the pump, clean the tank interior of all dirt

and foreign material.

2. Lubricate the threads of the inlet cover with Teflon

tape

or a thread-sealing compound approved for use with

petroleum fuels.

3. Extend the adjustable suction pipe to its full length and

carefully insert it into tank opening. The suction pipe will

adjust to the length needed and rest on the bottom of tank.

NOTE: The suction pipe supplied has a variable length of 22

to 40 inches. If additional length is needed, order the 15-

inch Suction Pipe Extension Kit.

4. Thread the inlet fitting of the pump onto the tank and turn

the pump to tighten snugly.

NOTE: To prevent the buildup of pressure and possible fuel

leakage through the nozzle, make sure the tank is vented.

Install Hose and Nozzle Assembly

Apply 3 to 4 wraps of Teflon

tape to the threaded end of the

hose and hand-tighten into the outlet cover until snug.

Install Handle

The HP-100 Hand Pump gives the operator a choice of two

flow settings:

•1/4 gallon setting has low resistance and pumps 1/4

gallon per stroke cycle.

•1/2 gallon setting has higher resistance and pumps 1/2

gallon per stroke cycle.

Volume per stroke is determined by connecting the piston

shaft to the appropriate handle setting as outlined below.

NOTE: Clevis pins may be installed from either side of handle.

1. Slide the handle grip onto the pump handle.

2. To install the links on the pump, insert a long clevis pin

through the link ends and the pump’s link holes. Secure

with a small cotter pin. (Figure 1)

4. Insert a screwdriver in the piston shaft of the pump and

pull the piston out. Install the shaft on the handle at either

piston hole by placing a short clevis pin through the handle

and the piston shaft end and securing with the hitch clip pin.

NOTE: Select the upper piston hole on the handle for the 1/2-

gallon setting (Figure 3) or the lower piston hole for the

1/4-gallon setting. Flow settings can be changed at any

time by repositioning the piston shaft on the handle.

To Dispense Fluid

1. Remove the nozzle from its holder and insert into the

receiving tank of the equipment or vehicle.

2. Choose a handle setting for the desired flow rate:

–1/4-gal. setting for low-volume, low-resistance pumping

–1/2-gal. setting for high-volume, high-resistance pumping

3. To operate pump, manually move the handle in a push/

pull motion.

4. After dispensing the desired amount of fluid, drain the

hose and nozzle. Place the nozzle in its holder and return

the handle to its upright storage position.

During daily use, the GPI HP-100 Hand Pump is essentially

maintenance free. However, the pump should be inspected

periodically for signs of leakage. If leaks are present, make

appropriate repairs. Refer to the Troubleshooting section.

Figure 2

Figure 3

Figure 4

OPERATION & MAINTENANCE

NOTE: Lock the handle to the pump by pushing the handle

against the pump and inserting a padlock through either

of the top holes in the handle and through the pump’s lock

hole. (Figure 4)

SYMPTOM PROBABLE CAUSE CORRECTIVE ACTION

A. FLUID LEAKS AROUND 1. Packing seals settled Tighten two screws on the retainer and torque to approximately 20 lb. in. (or hand

SHAFT SEAL tighten then another half turn until leak stops)

2. Seals worn Remove the two screws on the retainer and remove the retainer and bearing. Remove

all three seals and replace.

B. FLUID LEAKS AT 1. Anti-siphon valve or Replace vent plug assembly. Remove the black cap. Remove old vent plug assembly

ANTI-SIPHON VALVE O-ring damaged by turning counterclockwise. Install new vent plug assembly. Replace cap.

C. LOW FLOW RATE 1. Inlet screen clogged Remove the pump from the tank. Remove the suction pipe, spacer, and inlet

screen from the bottom of the pump. Clean the inlet screen and assemble. Place

the pump on the tank using installation instructions.

2. Suction pipe leak Remove the pump from the tank. Inspect the spacer and suction pipe to ensure

they are not worn or damaged. Replace as necessary and install the suction pipe

and pump again using installation instructions.

3. Piston ring or liner Remove the piston cover and inspect the piston ring and liner. Scoring and

worn severe scuffing on the liner indicates wear. If necessary, install an Overhaul Kit.

4. Piston cracked Remove the piston cover and inspect the piston. Install an Overhaul Kit, if necessary.

D. PUMP SEIZED 1. Debris in piston or Disassemble and clean the piston and liner. Check for debris lodged in the

liner piston ring or behind the liner. Small dimples in the liner indicate dirt, debris or

welding slag contaminants in the tank. Replace the piston ring and liner. If

appropriate, flush the tank of all contaminants.

TROUBLESHOOTING

Attach links to first hole

Use for 1/2 gallon setting

Use for 1/4 gallon setting

➤➤

1/2 gallon setting

shown here

➤➤

3. Attach the free ends of the links to the bottom, outer

surfaces of the handle. Insert a long clevis pin through the

holes on both links and the lowest hole on the handle.

Secure with a small cotter pin. (Figure 2)

ILLUSTRATED PARTS DRAWING

Kits and Accessories

114510-3 Hardware Kit includes handle grip, links, pins, and

screen.

114505-2 Overhaul Kit includes piston ring, three seals, pack-

ing seals, and liner.

114509-1 Inlet Cover Kit includes inlet cover, spacer, and

screen.

115527-2 Suction Pipe Extension, 15 inches.

Item No.n

No. Part No. Description Req’d.

114510-3 Hardware Kit ( ) ........................... 1

2 114014-2 Handle ............................................. 1

8904004-30 Screw, hex head, 10-32 x 5/8 in...... 2

9 114017-2 Retainer ........................................... 1

10 114016-1 Bearing ............................................ 1

13 114034-1 Packing Seal or (Kit ) .................. 3

14 114042-1 Body ................................................ 1

15 114009-1 Spring .............................................. 4

16 114007-1 Plate ................................................. 2

17 114008-1 Valve ................................................ 4

18 114043-4 Outlet Cover, 3/4 in. ........................ 1

19 904002-23 Screw, sems, 1/4-20 x 3/4 in......... 14

20 114006-1 Seal or (Kit ) ................................ 2

21 123504-1 Anti Siphon Vent Kit......................... 1

23 114041-1 Piston Cover .................................... 1

24 901001-51 Cover Seal or (Kit ) ...................... 1

25 906005-58 Piston Ring or (Kit ) ..................... 1

26 114021-1 Piston Assembly .............................. 1

27 114011-1 Liner or (Kit ) ............................... 1

32 114509-1 Inlet Cover Kit ( ) ......................... 1

34 114037-1 Inlet Screen or (Kit ) .................... 1

35 114038-1 Spacer or (Kit ) ............................ 1

36 110100-1 Adjustable Suction Pipe, 22-40 in. .. 1

37 114504-3 Hose and Nozzle Assembly Kit ....... 1

The HP-100 DUAL-FLO

Petroleum Hand Pump is compat-

ible with a wide variety of petroleum products and fits any

container with a 2-inch NPT bung.

Construction Lightweight, die-cast aluminum hous-

ing. Stainless steel piston shaft and

liner. Buna-N seals. Built-in air valve to

prevent leakage at the nozzle.

Pumping Capacity 1/2 gallon (1.9 litres) per stroke cycle.

Pumping Settings 1/2 gallon setting for high volume, high

resistance.

1/4 gallon setting for low volume, low

resistance.

Inlet Standard 1-inch NPT pipe.

Outlet Standard 3/4-inch NPT pipe.

Shipping Weight 14 lbs.

Hose and Nozzle 3/4 inch x 8 foot Buna-N hose. Thermo-

plastic unleaded nozzle. Built-in nozzle

holder.

Suction Pipe Plastic, adjustable 22 to 40 inches.

For warranty consideration, parts or other service informa-

tion, please contact your local distributor or the GPI Cus-

tomer Service Department in Wichita, Kansas, during normal

business hours.

1-800-835-0113

To obtain prompt, efficient service, be prepared with the

following information:

•The model number of your pump.

•The manufacturing date of your pump.

•Part descriptions and numbers.

Part descriptions and numbers can be obtained from the

Illustrated Parts Drawing.

For warranty service, be prepared with your original sales slip

or other evidence of purchase date.

U.S. Patent D 308,567

Dual-Flo and GPI are registered trademarks of

Great Plains Industries, Inc.

Printed in U.S.A.

SPECIFICATIONS PARTS AND SERVICE

5252 East 36th Street North

Wichita, KS USA 67220-3205

TEL: 316-686-7361

FAX: 316-686-6746

“A Great Plains Ventures Subsidiary”

www.gpi.net

1-800-835-0113

Rev. - 921407-0911/02

Limited Warranty Policy

GreatPlains Industries,Inc.5252 E.36

Street North,Wichita,KS USA67220-3205,hereby providesalimited twoyearwarranty against

defects in material and workmanship on all products manufactured by Great Plains Industries, Inc. except models BP-10, BP-12, CP-5,

D-12, D-24, D-115, D-230, LP-50 and RP-5. These models carry a 90-day warranty. The warranty shall extend to the purchaser of this

product and to any person to whom such product is transferred during the warranty period.

The warranty period shall begin on the date of the original new equipment purchase. Warrantor’s obligation hereunder shall be limited to

repairing defective workmanship or replacing or repairing any defective part or parts. This warranty shall not apply if:

A. the product has been altered or modified outside the warrantor’s duly appointed representative;

B. theproducthas beensubjectedtoneglect, misuse,abuseordamage or hasbeeninstalledor operatedotherthanin accordance

with the manufacturer’s operating instructions.

To make a claim against this warranty, notice of claim must be given in writing to the company at its above address no later than 30 days

aftertheexpirationofthe warranty period.Suchnoticeshallidentifythedefectin theproduct.Thecompanyshall,within14daysof receipt

of such notice, notify the customer to either send the product, transportation prepaid, to the company at its office in Wichita, Kansas, or

to duly authorized service center. The company shall perform all obligations imposed on it by the terms of this warranty within 60 days of

receipt of the defective product.

GREAT PLAINS INDUSTRIES, INC. EXCLUDES LIABILITY UNDER THIS WARRANTY FOR DIRECT, INDIRECT, INCIDENTAL AND

CONSEQUENTIAL DAMAGES INCURRED IN THE USE OR LOSS OF USE OF THE PRODUCT WARRANTED HEREUNDER.

Thecompanyherewithexpresslydisclaimsany warranty ofmerchantabilityorfitnessforanyparticularpurposeotherthan for whichitwas

designed.

This warranty gives you specific rights and you may also have other rights which vary from U.S. state to U.S. state.

Note: In compliance with MAGNUSON MOSS CONSUMER WARRANTY ACT – Part 702 (governs the resale availability of the warranty

terms).

Inhaltsverzeichnis

Andere GREAT PLAINS Wasserpumpe Handbücher

GREAT PLAINS

GREAT PLAINS PA-120DEF Bedienungsanleitung

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

Graco

Graco Husky 3300e Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung

STA-RITE

STA-RITE ST33APP Bedienungsanleitung