Greenheck FGI Fabra Hood Bedienungsanleitung

Step 1 Fabra hood Form F 471322

Figure 2 Fabra hood Form F 471322

Step 1

Open the shipping crates and separate the parts according to the size of the unit, refer to Figure 1.

Step 2

Place the two BASE ENDS and the two BASE SIDES in their approximate relationship to each other, see Figure 2.

Fasten together using three 1/4-20 fasteners per corner for 5 inch high base and four 1/4-20 fasteners per corner for

12 inch high base.

Note: Fasteners should be hand tightened only until step 4. On some units where the difference between the

hood width and throat width is greater than 32 inches, a REINFORCING PLATE is required in the corners of the

BASE, refer to Figure 2, Detail A.

Figure 2

Figure 1

Fabra Hood • Form F 1

Document 471322

Model FGI/FGR Fabra Hood

Form F - Single Section with Filters

Throat length less than or equal to 72 inches

Assembly Instructions

Please read and save these instructions for future reference. Read carefully before attempting to assemble, install,

operate or maintain the product described. Protect yourself and others by observing all safety information. Failure

to comply with these instructions will result in voiding of the product warranty and may result in personal injury

and/or property damage.

Figure 3 Fabra hood Form F 471322

Figure 4 Fabra hood Form F 471322

Step 3

Attach the HOOD SUPPORT ANGLE to the BASE ASSEMBLY (hand tight) using four 1/4-20 fasteners per angle,

see Figure 3, Detail B.

On some units, two DIAGONAL BRACES come pre-attached to the HOOD SUPPORT ANGLE. Fasten the loose

end of the DIAGONAL BRACES to the BASE ASSEMBLY using one 3/8-16 FASTENER per diagonal brace, see

Figure 3, Detail C.

Step 4

Tighten all BASE, SIDE and BASE END fasteners. Caulk all inside corners where the base sections come together.

At this point, the base may be lifted onto the roof curb before proceeding with further assembly.

Step 5

Attach the FILTER SIDE CHANNEL (hand tight) to the HOOD SUPPORT ANGLE and the FILTER SIDE CHANNEL

ASSEMBLY (hand tight) to the BASE SIDE, using two 5/16 X 1 inch weldstud fasteners per channel, see Figure 4.

Sandwich the END CLOSURE ANGLE between the BASE END and the SIDE FILTER CHANNEL ASSEMBLY, see

Figure 4.

Figure 3 Fabra hood Form F 471322

Figure 3

Figure 4

Fabra Hood • Form F2

Figure 5 Fabra hood Form F 471322

Figure 6 Fabra hood Form F 471322

NYLOC NUT

Step 6

Attach the END ANGLE (hand tight) to the ends of the SIDE FILTER CHANNEL ASSEMBLIES and SIDE CHANNELS

using four 5/16 X 1 weldstud fasteners per END ANGLE, see Figure 5. In addition, units with throat widths greater

than 36 inches will require FILTER END CHANNEL ASSEMBLIES, see Figure 5, Detail D. Fasten FILTER END

CHANNEL ASSEMBLY (hand tight) to the END CLOSURE ANGLE and END ANGLE, using two 5/16 X 1 weldstud

fasteners per assembly.

Step 7

Slide FILTERS in from both ends of unit. Tighten all FILTER CHANNEL and END ANGLE fasteners only after

FILTERS are in place.

Step 8

Attach the HOOD RAIL ASSEMBLY to the HOOD SUPPORT ANGLES using 3/8 x 3/4 inch bolt with 3/8 inch

Nyloc nut at each attachment point, see Figure 6.

NOTE: Fasteners should be hand tightened only until step 10.

Figure 5

Figure 6

Fabra Hood • Form F 3

Figure 7 Fabra hood Form F 471322

Step 9

Assemble HOOD PANELS

to HOOD RAIL ASSEMBLY.

The HOOD END ASSEMBLY

with the MALE RIB is to be

installed ﬁrst see Figure 7,

Detail E. Place the remaining

HOOD PANELS in place,

interlocking panels as you

go, see Detail E. Secure each

HOOD PANEL to the HOOD

RAIL ASSEMBLY as it is put

in place using four 12 X 3/8

inch sheet metal screws with

sealing washers per HOOD

PANEL. The HOOD END

ASSEMBLY with the FEMALE

RIB is to be installed last.

NOTE: Hoods over 9 feet

wide are supplied with

special HOOD CLIPS. See Detail F. HOOD

PANELS have predrilled holes for HOOD CLIP

installation. Install CLIPS as HOOD PANELS

are being put in place, using one 12 X 5/8 inch

sheet metal screw with sealing washer per

HOOD CLIP. To install CLIPS in the last panel,

remove the end FILTERS to provide access to

the underside of the hood. The FILTERS can

be easily replaced after the hood is completely

assembled.

Step 10 Fabra hood Form F 471322

Step 10

Tighten all pivot bracket fasteners. NOTE: There may be extra fasteners.

Figure 7

As a result of our commitment to continuous improvement, Greenheck reserves the right to change speciﬁcations

without notice.

Product warranties can be found online at Greenheck.com, either on the speciﬁc product page or in the literature

section of the website at Greenheck.com/Resources/Library/Literature.

Phone: 715.359.6171 • Fax: 715.355.2399 • Parts: 800.355.5354 • E-mail: [email protected] • Website: www.greenheck.com

Our Commitment

AMCA Publication 410-96, Safety Practices for Users and

Installers of Industrial and Commercial Fans, provides

additional safety information. This publication can be obtained

from AMCA International, Inc. at www.amca.org.

Greenheck's Gravity Ventilators catalog provides additional

information describing the equipment, fan performance,

available accessories, and speciﬁcation data.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Greenheck Lüfter Handbücher

Greenheck

Greenheck TBI Bedienungsanleitung

Greenheck

Greenheck LSF Series Bedienungsanleitung

Greenheck

Greenheck DF-18 Bedienungsanleitung

Greenheck

Greenheck AE Bedienungsanleitung

Greenheck

Greenheck G Bedienungsanleitung

Greenheck

Greenheck APEX Series Bedienungsanleitung

Greenheck

Greenheck AER-M Bedienungsanleitung

Greenheck

Greenheck GRSI Bedienungsanleitung

Greenheck

Greenheck SQ Bedienungsanleitung

Greenheck

Greenheck OFSD-211 Bedienungsanleitung

Greenheck

Greenheck MSCF-FC Bedienungsanleitung

Greenheck

Greenheck SMD-302 Bedienungsanleitung

Greenheck

Greenheck VFCB Bedienungsanleitung

Greenheck

Greenheck ERVe Series Bedienungsanleitung

Greenheck

Greenheck SQ 60-75 Bedienungsanleitung

Greenheck

Greenheck CRD-3 Series Installationsanleitung

Greenheck

Greenheck FA/103-00 Benutzerhandbuch

Greenheck

Greenheck PVE-20 Bedienungsanleitung

Greenheck

Greenheck SE1 Bedienungsanleitung

Greenheck

Greenheck ERS-MD Bedienungsanleitung

Greenheck

Greenheck AE Installationsanleitung

Greenheck

Greenheck DFD-M150 Bedienungsanleitung

Greenheck

Greenheck GreenJet GJI Bedienungsanleitung

Greenheck

Greenheck VFCD Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung