Greenheck ABD-Z2 Bedienungsanleitung

Receiving and Handling

Upon receiving dampers, check for both obvious

and hidden damage. If damage is found, record all

necessary information on the bill of lading and ﬁle

a claim with the ﬁnal carrier. Check to be sure that

all parts of the shipment, including accessories, are

accounted for.

Dampers must be kept dry and clean. Indoor storage

and protection from dirt, dust and the weather is

highly recommended. Do not store at temperatures in

excess of 100°F (38°C).

This manual is the property of the owner and is required for future maintenance. Please leave it with the owner when

the job is complete.

Safety Warning

Improper installation, adjustment, alteration, service

or maintenance can cause property damage, injury

or death. Read the installation, operating, and

maintenance instructions thoroughly before installing

or servicing this equipment.

Table of Contents

General Information . . . . . . . . . . . . . . . . . . 2

Electrical Guidelines . . . . . . . . . . . . . . . . . . 2

Setting Desired CFM on the ABD Damper . . . . . 2-3

Available Min/Max CFM Setpoints. . . . . . . . . . . 4

Mounting the ABD-Z2 in the ceiling . . . . . . . . . . 5

Actuator Connections . . . . . . . . . . . . . . . . . 5

Damper Maintenance . . . . . . . . . . . . . . . . . 5

ABD-Z2 1

Document 485148

ABD-Z2

Automatic Balancing Damper

for Zone Register Terminals

Installation, Operation and Maintenance Manual

Please read and save these instructions for future reference. Read carefully before attempting to assemble, install,

operate or maintain the product described. Protect yourself and others by observing all safety information. Failure

to comply with these instructions will result in voiding of the product warranty and may result in personal injury

and/or property damage.

General Installation

Verify the minimum and maximum setpoints are in the available range (see Figure 3 and 4).

Adjusting the Minimum CFM

Loosen the bolt to adjust to move drive link to primary or alternate linkage location. See Detail A for correct linkage

location.

Adjusting the Maximum CFM

How the maximum CFM adjusted. Loosen the wing nut on crank arm, adjust full-open stop clockwise until speciﬁed

maximum CFM setpoint is achieved. Tighten wing nut.

Note: ABD-Z2 is adjustable in the ﬁeld. Make sure full open stop does not over travel. If you over adjust, you can

wreck the unit.

Electrical Guidelines

All wiring shall be done in accordance with the

National Electrical Code ANSI/NFPA-70 latest edition,

any local codes that may apply, and wiring diagrams

developed in compliance with the job or project

design and speciﬁcations.

Important!

Electrical input may be needed for this equipment.

This work should be performed by a qualiﬁed

electrician. Verify power before wiring actuator.

Greenheck is not responsible for any damage to, or

failure of the unit caused by incorrect ﬁeld wiring. To

avoid causing death or serious bodily harm to building

occupants, follow all instructions carefully. Dampers

must close completely to preserve the integrity of the

ﬁre smoke separation.

Setting Desired CFM on the ABD Damper

Detail A

Alternate linkage location

Use for units with minimum

cfm of 75 or more

Primary linkage location

Use for units with minimum

cfm less than 75

Alternate linkage location

Primary linkage location

ABD

Actuator

Crankarm

wing nut

Figure 1: ABD-Z2 4 inch

ABD-Z22

Detail A

Alternate linkage location

Use for units with

minimum cfm of 105 or

Primary linkage location

Use for units with minimum

cfm less than 105

Alternate linkage location

Primary linkage location

crankarm

ABD

wing nut

Figure 2: ABD-Z2 6 inch

ABD-Z2 3

Available Max/Min CFM Set Points for ABD-Z2 4 inch

Minimum CFM Setpoint

Maximum CFM Setpoint

100

105

33 X

35 X X

40 X X X

45 X X X X

48 X X X X X

50 X X X X X X

55 X X X X X X X

60 X X X X X X X X

68 X X X X X X X X X

75 X X X X X X X X X X

80 X X X X X X X X X X X

85 X X X X X X X X X X X X

90 X X X X X X X X X X X X X

95 X X X X X X X X X X X X X X

100 X X X X X X X X X X X X X X X

105 X X X X X X X X X X X X X X X X

115 X X X X X X X X X X X X X X X X X

125 X X X X X X X X X X X X X X X X X X

Available Max/Min CFM Set Points for ABD-Z2 6 inch

Minimum CFM Setpoint

Maximum CFM Setpoint

105

113

120

135

143

150

160

170

180

193

65 X

70 X X

75 XXX

80 XXXX

85 XXXXX

90 XXXXXX

98 XXXXXXX

105 XXXXXXXX

113 XXXXXXXXX

120 XXXXXXXXXX

135 XXXXXXXXXX X

143 XXXXXXXXXXXX

150 XXXXXXXXXX X X X

160 XXXXXXXXXXXXXX

170 XXXXXXXXXXXXXXX

180 XXXXXXXXXXXXXXXX

193 XXXXXXXXXXXXXXXXX

205 XXXXXXXXXXXXXXXXXX

217 XXXXXXXXXXXXXXXXXXX

228 XXXXXXXXXXXXXXXXXXX

240 XXXXXXXXXXXXXXXXXX

260 X X XXXXXX

Figure 3: CFM

setpoints for

ABD-Z2 4 inch

Figure 4: CFM

setpoints for

ABD-Z2 4 inch

ABD-Z24

X = Adjustment with linkage in primary position

X= Adjustment with linkage in alternate position

Damper Maintenance

Dampers do not typically require maintenance as long as they are kept dry and clean. If cleaning is necessary, wash

with water. No solvents should be used in cleaning, as they could damage the valve or gasket. In addition, ABD

dampers incorporate Steri-BalanceTM into all plastic components. Steri-BalanceTM is a non-caustic material that

inhibits antimicrobial growth.

Actuator Connections

Electrical connections to damper actuators should be made in accordance with wiring and piping diagrams

developed in compliance with applicable codes, ordinances and regulations (see Electrical Guidelines).

BLACK

ORANGE

BLACK

Mounting the ABD-Z2 in the Ceiling

1)Attach the hanger brackets provided to the damper. Dampers shall be supported in a minimum of two places on

opposite sides of the damper.

2) Insert the ABD-Z2 between the ceiling joists. Attach the hangers to the ceiling joist using 2 - #8 x 3⁄4in. nails.

3)Attach the ductwork to the collar of the plenum box.

4)Install the grille.

1. Damper

2. Plaster flange

3. Gypsum board

4. Grille

5. RC channel

6. Hanging strap, angle, or wire

7. Horizontal support stud or angle

Figure 5: Mounting

in the ceiling

Figure 6: wiring diagram

ABD-Z2 5

ABD-Z26

ABD-Z2 7

As a result of our commitment to continuous improvement, Greenheck reserves the right to change speciﬁcations

without notice.

Product warranties can be found online at Greenheck.com, either on the speciﬁc product page or in the literature

section of the website at Greenheck.com/Resources/Library/Literature.

Phone: 715.359.6171 • Fax: 715.355.2399 • Parts: 800.355.5354 • E-mail: [email protected] • Website: www.greenheck.com

Our Commitment

Inhaltsverzeichnis

Andere Greenheck Feuer- und Rauchklappe Handbücher

Greenheck

Greenheck EHM-601 Bedienungsanleitung

Greenheck

Greenheck ESK-402 Montage- und Bedienungsanleitung

Greenheck

Greenheck DFD Series Bedienungsanleitung

Greenheck

Greenheck CRD-1WT Handbuch

Greenheck

Greenheck GFSD Series Bedienungsanleitung

Greenheck

Greenheck FD150X Montage- und Bedienungsanleitung

Greenheck

Greenheck FSD Series Bedienungsanleitung

Greenheck

Greenheck CRD-300WT Bedienungsanleitung

Greenheck

Greenheck FD Series Betriebsanleitung

Greenheck

Greenheck HTD Series Bedienungsanleitung

Greenheck

Greenheck EHH-401 Bedienungsanleitung

Greenheck

Greenheck HBS Series Handbuch

Greenheck

Greenheck RBD Series Bedienungsanleitung

Greenheck

Greenheck SMD Series Bedienungsanleitung

Greenheck

Greenheck Multi-Blade DFD Series Bedienungsanleitung

Greenheck

Greenheck DFD Series Bedienungsanleitung

Greenheck

Greenheck FSD Series Betriebsanleitung

Greenheck

Greenheck HPR Series Bedienungsanleitung

Greenheck

Greenheck CFSD Series Bedienungsanleitung

Greenheck

Greenheck HPR Series Bedienungsanleitung

Greenheck

Greenheck FSD Series Handbuch

Greenheck

Greenheck FSDR Series Bedienungsanleitung

Greenheck

Greenheck MBD-15 Bedienungsanleitung

Greenheck

Greenheck DFD Series Bedienungsanleitung

Beliebte Feuer- und Rauchklappe Handbücher anderer Marken

HVC

HVC NCA 700 Series Bedienungsanleitung

Wildeboer

Wildeboer FR90 Bedienungsanleitung

FläktGroup

FläktGroup ETCE Programmierhandbuch

Tamco

Tamco 1000 SM Series Bedienungsanleitung

Lindab

Lindab FBC2 Installations- und Betriebshandbuch

EKOVENT

EKOVENT EKO-SRB1 Montageanleitung

Advanced Air

Advanced Air 0160 Series Bedienungsanleitung

Swegon

Swegon Actionair CSS Series Bedienungsanleitung

TAKACHIHO

TAKACHIHO FYN-M 1 Series Bedienungsanleitung

Valmet

Valmet Flowrox Expulse Series Handbuch

ETS NORD

ETS NORD NORDfire FDMB Bedienungsanleitung

Mandik

Mandik MSD Bedienungsanleitung

AMS

AMS CR2 Bedienungsanleitung

Arzel

Arzel RegiDamper Bedienungsanleitung

mercor

mercor mcr S-THERM C Bedienungsanleitung

Mandik

Mandik FDMA-PM Bedienungsanleitung

BSB

BSB FD-C Montageanleitung

Slant/Fin

Slant/Fin JA Series Leitfaden