Greenheck FD Series Betriebsanleitung

Application

Factory installed sleeves may need to be extended in the ﬁeld. This supplement covers the following applications:

• When the factory sleeve extends all the way through the rated barrier (Figure 1)

• When the factory sleeve ends in the plane of the rated barrier (Figure 2).

Figure 1: Factory sleeve extends all the way

through the rated barrier.

Fire or Fire Smoke

Damper

Fire Rated Partition

Factory Sleeve

Minimum 1 in.

Overlap

Sleeve

Extension

Refer to:

‘Installation Instructions for FD, DFD, DFD X series, and FD

X series Fire Damper Models’ (Part #481324)

‘Installation Instructions for FSD-XXX, DFD-XXX, and

SSFSD-XXX Series Fire & Combination Fire Smoke

Dampers’ (Part #481318) for additional details.

This supplemental installation instruction provides details for attachment of the sleeve extension. Consult Authority

Having Jurisdiction (AHJ) for approval.

Notes

1. Sleeve extension must be same material and gage as factory sleeve.

2. The inside dimensions of the sleeve extension must be the same dimensions as the outside dimensions of the

factory sleeve.

Factory Sleeve Sleeve Extension

Connecting Joint of Sleeves

See notes 4,5, and 7 Fire or Combination Fire

Smoke Damper

Figure 2: Factory sleeve ends in the plane of the rated

barrier.

Sleeve Extensions 1

Document 462103

Sleeve Extensions

Installation Instruction Supplement

FD & DFD Series Fire Dampers

and FSD Series

Combination Fire Smoke Dampers

3. Sleeve extension must overlap the factory sleeve a minimum of 1 in. (25 mm).

4. All four sides of the sleeve extension must be attached to the factory sleeve. Attachments must be spaced

a maximum of 6 in. (152 mm) on center and a maximum of 2 in. (51 mm) from corners. A minimum of 2

attachments per side (8 per damper) are required. One of the methods of attachment shown below must be

used.

• tack or spot welds

• #10 sheet metal screws

• ¼ in. (6 mm) bolts and nuts

•

3⁄16 in. (4.7 mm) steel pop rivets

5. Products with a smoke rating (FSD models) require that the joint between the two sleeves be sealed. Approved

caulks include:

• G.E. 1200 series silicone construction adhesive

• Component Hardware Group (QMFZ2) silicone SLT-5000 or SLT-5200

• Silico (QMFZ2) silicone SB or CH (E224060)

• Dow Corning (QMFZ2) silicone SLT-5200 (E40195)

• Dow R/C (QMFZ2) silicone Type RTV732.

Approved duct sealants include:

• Precision PA2084T duct sealant adhesive

• Design Polymerics DP1010 water base duct sealant

• Grey Pookie

• Ductmate PROseal®

• CL Ward S seal

6. Sleeve extensions can be made to either end of the factory sleeve. However, the total sleeve length cannot

extend more then 16 in. (406 mm) on the actuator side and not more than 6 in. (152 mm) on the non-actuator

side.

7. The joint created by the factory sleeve and sleeve extension cannot be in the plane of the partition.

Phone: 715.359.6171 • Fax: 715.355.2399 • Parts: 800.355.5354 • E-mail: [email protected] • Website: www.greenheck.com

As a result of our commitment to continuous improvement, Greenheck reserves the right to change speciﬁcations

without notice.

Product warranties can be found online at Greenheck.com, either on the speciﬁc product page or in the

literature section of the website at Greenheck.com/Resources/Library/Literature.

Our Commitment

Andere Handbücher für FD Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Greenheck Feuer- und Rauchklappe Handbücher

Greenheck

Greenheck VCD Series Bedienungsanleitung

Greenheck

Greenheck Vektor-MD Bedienungsanleitung

Greenheck

Greenheck FSD Series Bedienungsanleitung

Greenheck

Greenheck SMD Series Bedienungsanleitung

Greenheck

Greenheck HBT Series Bedienungsanleitung

Greenheck

Greenheck MBD-15 Bedienungsanleitung

Greenheck

Greenheck RBD Series Bedienungsanleitung

Greenheck

Greenheck CRD-1WT Bedienungsanleitung

Greenheck

Greenheck FSD Series Handbuch

Greenheck

Greenheck FD150X Montage- und Bedienungsanleitung

Greenheck

Greenheck Vektor-M Series Bedienungsanleitung

Greenheck

Greenheck FSDR Series Montage- und Bedienungsanleitung

Greenheck

Greenheck FD150X Handbuch

Greenheck

Greenheck CFSD Series Bedienungsanleitung

Greenheck

Greenheck ODFD Series Bedienungsanleitung

Greenheck

Greenheck GFSD Series Bedienungsanleitung

Greenheck

Greenheck DFD Series Bedienungsanleitung

Greenheck

Greenheck DFD Series Bedienungsanleitung

Greenheck

Greenheck HPR Series Bedienungsanleitung

Greenheck

Greenheck HSD-401 Handbuch

Greenheck

Greenheck ESD-603 Bedienungsanleitung

Greenheck

Greenheck FD Series Handbuch

Greenheck

Greenheck FD 150 Series Bedienungsanleitung

Greenheck

Greenheck FSD Series Betriebsanleitung

Beliebte Feuer- und Rauchklappe Handbücher anderer Marken

HVC

HVC NCA 700 Series Bedienungsanleitung

Wildeboer

Wildeboer FR90 Bedienungsanleitung

FläktGroup

FläktGroup ETCE Programmierhandbuch

Tamco

Tamco 1000 SM Series Bedienungsanleitung

Lindab

Lindab FBC2 Installations- und Betriebshandbuch

EKOVENT

EKOVENT EKO-SRB1 Montageanleitung

Advanced Air

Advanced Air 0160 Series Bedienungsanleitung

Swegon

Swegon Actionair CSS Series Bedienungsanleitung

TAKACHIHO

TAKACHIHO FYN-M 1 Series Bedienungsanleitung

Valmet

Valmet Flowrox Expulse Series Handbuch

ETS NORD

ETS NORD NORDfire FDMB Bedienungsanleitung

Mandik

Mandik MSD Bedienungsanleitung

AMS

AMS CR2 Bedienungsanleitung

Arzel

Arzel RegiDamper Bedienungsanleitung

mercor

mercor mcr S-THERM C Bedienungsanleitung

Mandik

Mandik FDMA-PM Bedienungsanleitung

BSB

BSB FD-C Montageanleitung

Slant/Fin

Slant/Fin JA Series Leitfaden