Greenlee CM-410 Bedienungsanleitung

CM-410

Digital

Clamp-on Meter

Medidor digital

con pinza

Contrôleur

numérique

à pince

INSTRUCTION MANUAL

MANUAL DE INSTRUCCIONES

MANUEL D’INSTRUCTIONS

Read and understand all of the instructions and

safety information in this manual before

operating or servicing this tool.

Lea y entienda todas las instrucciones y la

información sobre seguridad que aparecen en

este manual, antes de manejar esta herramienta

o darle mantenimiento.

Lire attentivement et bien comprendre toutes les

instructions et les informations sur la sécurité de

ce manuel avant d‘utiliser ou de procéder à

l‘entretien de cet outil.

Description

The Greenlee CM-410 Digital Clamp-on Meter is a hand-held testing device

capable of measuring up to 400 amps of alternating current, in addition to

measuring AC or DC voltage, resistance, and checking continuity.

Safety

Safety is essential in the use and maintenance of Greenlee tools and

equipment. This instruction manual and any markings on the tool provide

information for avoiding hazards and unsafe practices related to the use of

this tool. Observe all of the safety information provided.

Purpose of This Manual

This instruction manual is intended to familiarize all personnel with the

safe operation and maintenance procedures for the Greenlee CM-410

Digital Clamp-on Meter.

Keep this manual available to all personnel.

Replacement manuals are available upon request at no charge:

www.greenlee.com.

KEEP THIS MANUAL

All specifications are nominal and may change as design improvements occur.

Greenlee Textron Inc. shall not be liable for damages resulting from misapplication or

misuse of its products.

® Registered: The color green for electrical test instruments is a registered trademark

of Greenlee Textron Inc.

Do not discard this product or throw away!

For recycling information, go to www.greenlee.com.

CM-410

Important Safety Information

Electric shock hazard:

Contact with live circuits could result in severe

injury or death.

Read and understand this material before

operating or servicing this equipment. Failure to

understand how to safely operate this tool could

result in an accident causing serious injury or

death.

This symbol is used to call your attention to hazards or unsafe

practices which could result in an injury or property damage. The

signal word, defined below, indicates the severity of the hazard. The

message after the signal word provides information for preventing or

avoiding the hazard.

SAFETY ALERT SYMBOL

Immediate hazards which, if not avoided, WILL result in severe injury

or death.

Hazards which, if not avoided, COULD result in severe injury or death.

Hazards or unsafe practices which, if not avoided, MAY result in injury

or property damage.

Important Safety Information

Electric shock and fire hazard:

• Do not expose this unit to rain or moisture.

• Do not use the unit if it is wet or damaged.

• Use this unit for the manufacturer’s intended purpose only, as

described in this manual. Any other use can impair the protection

provided by the unit.

Failure to observe these warnings could result in severe injury or death.

Electric shock hazard:

• Do not operate with the case or battery door open.

• Before opening the case or battery door, remove the test leads

(or jaw) from the circuit and shut off the unit.

Failure to observe these warnings could result in severe injury or death.

Electric shock hazard:

• Using this unit near equipment that generates electromagnetic

interference can result in unstable or inaccurate readings.

• Unless measuring voltage or current, shut off and lock out power.

Make sure that all capacitors are discharged. Voltage must not be

present.

Failure to observe these warnings could result in severe injury or death.

CM-410

Electric shock hazard:

• Do not attempt to repair this unit. It contains no user-serviceable

parts.

• Do not expose the unit to extremes in temperature or high humidity.

Refer to “Specifications.”

Failure to observe these precautions may result in injury and can

damage the unit.

Important Safety Information

Electric shock hazard:

Do not change the measurement function while the test leads are

connected to a component or circuit.

Failure to observe this precaution may result in injury and can damage

the unit.

Identification

1. Jaw

2. Lever

3. Selector switch

4. Display

5. Negative, common (COM), or

ground input terminal

6. Volts or resistance (V-Ω) input

terminal

7. Select/toggle button

8. Hold button

910111213141516

Symbols on the Unit

Warning—Read the instruction manual

Risk of electric shock

Double insulation

Battery

Recycle product in accordance with manufacturer’s directions

Display Icons

9. Hold function is enabled.

10. A Amps

11. V Volts

12. ΩOhms

13. k kilo (103)

14. M Mega (106)

15. Continuity mode

16. Auto ranging is enabled.

17. AC measurement is selected.

18. –Negative polarity indicator

19. DC measurement is selected.

20. Low battery indicator

21.

O.L

Overload indicator

CM-410

Using the Features

•Selector Switch

Slide switch to desired mode of operation:

(amps)

(AC/DC voltage)

(ohms/continuity)

Return switch to OFF position when not in use.

•Select/Toggle Button

Momentarily press button to select AC or DC voltage, ohms, or

continuity mode.

•Hold Button

Press momentarily to hold the present value on the display. will

appear on the display.

Press again to return to normal mode.

•Auto Power Off

The unit automatically shuts off after approximately 10 minutes of

inactivity.

Operation

1. Set the selector switch according to the Settings Table. Momentarily

press the select/toggle button to select mode.

2. Refer to “Typical Measurements”for specific measurement

instructions.

3. Test the unit on a known functioning circuit or component.

•If the unit does not function as expected on a known functioning

circuit, replace the battery.

•If the unit still does not function as expected, send the unit to

Greenlee for repair. Refer to the instructions under the Warranty.

4. Take the reading from the circuit or component to be tested.

Settings Table

Electric shock hazard:

Contact with live circuits could result in severe

injury or death.

To measure

this value …

Connect

red lead

to …

Connect

black lead

to …

Momentarily press

the Select/Toggle

Button until this

icon appears

on the display …

Set the

Selector Switch

to this

symbol …

AC Amps* N/A N/AN/A

AC Voltage V-Ω COM

DC Voltage V-Ω COM

Continuity** V-Ω COM

Resistance V-Ω COM

M Ω

*AC Amp measurements are made using the jaw clamp. Refer to “Typical

Measurements”for specific measurement instructions.

**Tone indicates a circuit resistance of less than 20 Ω.

CM-410

Typical Measurements

Clamp Around Line Splitter

Notes:

•The Greenlee 93-30 Line Splitter is

divided. One section renders amps; the

other renders amps multiplied by 10.

•Close the jaw completely to ensure

accurate measurement.

•Center the line splitter in the jaw for

highest accuracy.

Clamp Around Wire

Notes:

•Clamp the jaw around one

conductor only.

•Close the jaw completely to

ensure accurate measurement.

•Center the wire in the jaw for

highest accuracy.

AC Amps

Typical Measurements

Voltage

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Greenlee Multimeter Handbücher

Greenlee

Greenlee 93-105 Bedienungsanleitung

Greenlee

Greenlee DM-20 Bedienungsanleitung

Greenlee

Greenlee DM-25 Bedienungsanleitung

Greenlee

Greenlee DM-200A Bedienungsanleitung

Greenlee

Greenlee CMI-200 Bedienungsanleitung

Greenlee

Greenlee PDMM-20 Bedienungsanleitung

Greenlee

Greenlee CMT-80 Bedienungsanleitung

Greenlee

Greenlee DM-860A Bedienungsanleitung

Greenlee

Greenlee 93-502 Bedienungsanleitung

Greenlee

Greenlee CM-400 Bedienungsanleitung

Greenlee

Greenlee CM-1500 Bedienungsanleitung

Greenlee

Greenlee DM-860 Bedienungsanleitung

Greenlee

Greenlee 93-97 Bedienungsanleitung

Greenlee

Greenlee CM-450 Bedienungsanleitung

Greenlee

Greenlee CM-1500 Bedienungsanleitung

Greenlee

Greenlee CM-330 Bedienungsanleitung

Greenlee

Greenlee DM-60 Bedienungsanleitung

Greenlee

Greenlee DM-100 Bedienungsanleitung

Greenlee

Greenlee CM-1050 Bedienungsanleitung

Greenlee

Greenlee DM-60 A Bedienungsanleitung

Greenlee

Greenlee GRDM-45 Bedienungsanleitung

Greenlee

Greenlee PDMM-10 Bedienungsanleitung

Greenlee

Greenlee CM-750 Bedienungsanleitung

Greenlee

Greenlee DM-500 Bedienungsanleitung

Beliebte Multimeter Handbücher anderer Marken

Agilent Technologies

Agilent Technologies 34420A Bedienungsanleitung

Fluke

Fluke 83 Bedienungsanleitung

Hameg

Hameg HM 8012 Bedienungsanleitung

Mastech

Mastech MY70 Bedienungsanleitung

Steren

Steren MUL-300 Bedienungsanleitung

Somogyi Elektronic

Somogyi Elektronic home SMA 92 Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRAmax 6 Bedienungsanleitung

PeakTech

PeakTech 4000 Gebrauchs- und Pflegehandbuch

YOKOGAWA

YOKOGAWA 90050B Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRALINE DMM16 Bedienungsanleitung

Fluke

Fluke 8846A Bedienungs- und Wartungshandbuch

Tempo Communications

Tempo Communications MM200 Bedienungsanleitung

Elenco Electronics

Elenco Electronics CM-1555 Bedienungsanleitung

Mastech

Mastech MS8238C Bedienungsanleitung

SDAR

SDAR 830A, 830B, 830D, 830C Bedienungsanleitung

RS PRO

RS PRO RS-9519BT Bedienungsanleitung

BGS technic

BGS technic 8890 Bedienungsanleitung

Amprobe

Amprobe Hexagon 60 Bedienungsanleitung