Greenlee GATOR EK22GL Bedienungsanleitung

INSTRUCTION MANUAL

Read and understand all of the instructions and

safety information in this manual before operating

or servicing this tool.

GATOR®EK22GL

Battery-powered,

High-speed Crimping Tool

EK22GL Battery-powered, High-speed CrimpingTool

Greenlee Textron / Subsidiary of Textron Inc. 24455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815/397-7070

All specifications are nominal and may change as design improve-

ments occur. Greenlee Textron shall not be liable for damages

resulting from misapplication or misuse of its products.

GATOR is a registered trademark of Greenlee Textron.

AVIA is a registered trademark of Avia International.

Blackburn is a registered trademark of Thomas & Betts.

Mobil is a registered trademark of Mobil Oil Corporation.

NUTO is a registered trademark of Exxon Corporation.

Tellus is a registered trademark of Shell Oil Company.

KEEPTHIS MANUAL

Table of Contents

Description .....................................................................2

Safety .............................................................................2

Purpose of this Manual ..................................................2

Important Safety Information......................................3–4

Identification ................................................................... 5

Specifications ................................................................. 5

Operation ...................................................................6–7

Dies and Connectors......................................................8

Maintenance...................................................................9

Troubleshooting ...........................................................10

Disassembly.................................................................11

Assembly......................................................................12

Illustrations .............................................................13–15

Parts List ................................................................16–18

Description

The EK22GL Battery-powered, High-speed Crimping

Tool is a hand-held, self-contained crimping tool

intended to crimp copper cable with K22-type and

W-type dies.

Safety

Safety is essential in the use and maintenance of

Greenlee tools and equipment. This manual and any

markings on the tool provide information for avoiding

hazards and unsafe practices related to the use of this

tool. Observe all of the safety information provided.

Purpose of this Manual

This manual is intended to familiarize all personnel with

the safe operation and maintenance procedures for the

following Greenlee tool:

EK22GL Battery-powered, High-speed

Crimping Tool

Keep this manual available to all personnel.

Replacement manuals are available upon request at no

charge.

EK22GL Battery-powered, High-speed CrimpingTool

Greenlee Textron / Subsidiary of Textron Inc. 34455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815/397-7070

IMPORTANT SAFETY INFORMATION

This symbol is used to call your attention to hazards

or unsafe practices which could result in an injury or

property damage. The signal word, defined below,

indicates the severity of the hazard. The message

after the signal word provides information for

preventing or avoiding the hazard.

Hazards or unsafe practices which, if not avoided,

MAY result in injury or property damage.

Hazards which, if not avoided, COULD result in

severe injury or death.

Immediate hazards which, if not avoided, WILL

result in severe injury or death.

SAFETY

ALERT

SYMBOL

Read and understand all of the

instructions and safety information in

this manual before operating or

servicing this tool.

Failure to observe this warning can

result in severe injury or death.

Skin injection hazard:

Do not use hands to check for oil

leaks. High pressure oil easily

punctures skin causing serious

injury, gangrene, or death. If injured,

seek medical help immediately to

remove oil.

Wear eye protection when operating

or servicing this tool.

Failure to wear eye protection can

result in serious eye injury from

flying debris or hydraulic oil.

Do not use solvents or flammable

liquids to clean the crimping tool.

Solvents or flammable liquids could

ignite and cause serious injury or

property damage.

An incomplete crimp can cause a fire.

• Use proper die, connector, and cable combina-

tions. Improper combinations can result in an

incomplete crimp.

• Use only W-type dies on aluminum connectors or

aluminum wire. Mismatched components can

result in an incomplete crimp.

• The relief valve will sound to indicate a completed

crimp. If you do not hear the sound of the relief

valve, the crimp is not complete.

Failure to observe these warnings can result in

severe injury or death.

Electric shock hazard:

This tool is not insulated. When

using this unit near energized

electrical lines, use proper personal

protective equipment.

Failure to observe this warning can

result in severe injury or death.

EK22GL Battery-powered, High-speed CrimpingTool

Greenlee Textron / Subsidiary of Textron Inc. 44455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815/397-7070

EK22GL Battery-powered, High-speed CrimpingTool

Greenlee Textron / Subsidiary of Textron Inc. 54455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815/397-7070

IdentificationIdentification

Specifications

EK22GL

1. Housing

2. Retract Button

3. Battery Cartridge

4. Trigger

5. Battery Load Display

6. Locking Flange

7. Die Release Buttons

8. W-type Die Detents

9. Crimping Dies

10. Crimping Head

11. Oil Reservoir

12. Oil Plug

Crimping Tool

Length........................................................................................... 314 mm (12-3/8")

Width........................................................................................................76 mm (3")

Height ........................................................................................... 298 mm (11-3/4")

Mass/Weight (with battery) ................................................................. 4.4 kg (9.7 lb)

Sound Level..............................................................................75 dB (A) at 1 meter

Vibration.................................................................................................... < 2.5 m/s2

Motor Type....................................................................... DC permanent field motor

Motor Voltage ...............................................................................................12 VDC

Hydraulic Oil ....................................................50 ml (0.1 pint) of Shell Tellus®T 15

Crimping Capacities

Maximum Cable Size.................................................................... 600 Kcmil copper

Maximum Crimping Force................................................................55 kN (6.2 tons)

Crimping Time ..........................................................................................7 seconds

Crimps per Charge ......................................................................approximately 120

Battery

Charging Voltage ...............................................................................................12 V

Charging Time ................................................................................................ 1 hour

EK22GL Battery-powered, High-speed CrimpingTool

Greenlee Textron / Subsidiary of Textron Inc. 64455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815/397-7070

Operation

Charging the Battery

Read the instructions supplied with the battery charger.

Battery Condition

Wear eye protection when operating

or servicing this tool.

Failure to wear eye protection can

result in serious eye injury from

flying debris or hydraulic oil.

Electric shock hazard:

This tool is not insulated. When

using this unit near energized

electrical lines, use proper personal

protective equipment.

Failure to observe this warning can

result in severe injury or death.

Keep hands away from the crimping

head when crimping.

Failure to observe this warning can

result in severe injury or death.

• Do not operate the tool without dies. Damage to

the ram or crimping head can result.

• Do not operate with the crimping head open.

Damage to the ram or seals can result.

• This tool is not designed for continuous use.

After 30 to 40 crimping cycles, allow the crimping

tool to cool for 15 minutes.

• Do not place the tool in a vise. The crimping tool

is designed for hand-held operation.

• Protect the crimping tool from rain and moisture.

Water will damage the crimping tool and battery.

• Use this tool for the manufacturer’s intended

purpose only.

Failure to observe these precautions can result in

injury or property damage.

Battery Load Display Battery Condition

Momentary illumination at Normal or operating

beginning of crimp charge level

Flickering at point of Normal or operating

maximum crimping force charge level

Flickering during entire Low charge level

crimping cycle

Constant illumination when Low charge level

operating without a load

Installing K22-type Dies

1. Select the proper dies for the intended crimp.

2. Push the die release button.

3. Slide the die into the crimping head until it “snaps”

into place.

4. Properly position the second die. Repeat Steps

2 and 3.

Installing W-type Dies

1. Push the die release button.

2. Slide the die adapter (Greenlee part number

500 4292.0) into crimping head until it “snaps”

into place.

Note: The die adapters have the “D

” die profile.

No additional dies are needed if the connector to be

crimped requires a “D

” die.

3. Repeat for the other adapter.

4. Select the proper dies for the intended crimp.

5. Press the locking flange and open the crimping

head.

6. Push the W-type die detent and slide the W-type die

into place.

7. Properly position the second die. Repeat Steps

5 and 6.

EK22GL Battery-powered, High-speed CrimpingTool

Greenlee Textron / Subsidiary of Textron Inc. 74455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815/397-7070

Operation (cont’d)

Preparing Cable

Follow the lug manufacturer’s instructions for appropriate

cable strip length.

CRIMPING DIRECTION

1ST COMPRESSION

CRIMPING DIRECTION

SIDE A

CRIMPING DIRECTION

SIDE B

1ST COMPRESSION

SIDE A

1ST COMPRESSION

SIDE B

Crimping Cable

1. Press the locking flange and open the crimping

head.

2. Insert the properly assembled connector into the

crimping head.

3. Close the crimping head.

4. Pull the trigger to make the crimp.

5. Hold the trigger down until the crimping tool

achieves pressure relief.

Notes: Pressure relief occurs at approximately

690 bar (10,000 psi) and is accompanied by an

audible “pop”.

It is normal for the battery load display to light at

both the beginning and near the end of the crimping

cycle.

An incomplete crimp can cause a fire.

• Use proper die, connector, and cable combina-

tions. Improper combinations can result in an

incomplete crimp.

• Use only W-type dies on aluminum connectors or

aluminum wire. Mismatched components can

result in an incomplete crimp.

• The relief valve will sound to indicate a completed

crimp. If you do not hear the sound of the relief

valve, the crimp is not complete.

Failure to observe these warnings can result in

severe injury or death.

6. The crimping tool returns automatically.

7. Position the crimping tool for next crimp. Repeat

Steps 4 through 6 for the number of crimps as

described in this manual.

8. Open the crimping head and remove the connector.

Notes: If it is necessary to retract the ram before a

crimping cycle is completed, push the retract button.

Pushing the retract button will result in the complete

retraction of the ram.

After completing the last crimp with W-type dies on an

aluminum connector, wipe off the excess oxide inhibitor.

EK22GL Battery-powered, High-speed CrimpingTool

Greenlee Textron / Subsidiary of Textron Inc. 84455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815/397-7070

Dies and Connectors

Die Selection

Crimps made on copper cable with Greenlee K22-type dies and

the connectors listed here are UL classified and CSA certified.

Refer to “Connector Selection” for brand names and model

numbers of appropriate lugs as well as crimping instructions.

W-type dies can be used to crimp #6 AWG to 4/0 AWG alumi-

num or copper cable.

Connector Selection

EK22GL Crimping Range: #8 AWG to 600 Kcmil

When used with K22-type dies, this tool is UL classified and CSA certified for use with the following connector brands:

* Use the number of crimps listed in the last column

instead of the number provided with the connector:

A — #8 to 1/0: 1 crimp

2/0 to 600: 2 crimps

B — #8 to 1/0: 2 crimps

2/0 to 3/0: 3 crimps

4/0 to 600: 4 crimps

LR9716195R7

Part UPC Cable Color

Number Number Size Code

K22-0 03079 #8 AWG Red

K22-1 03080 #6 AWG Blue

K22-2 03081 #4 AWG Gray

K22-3 03082 #2 AWG Brown

K22-31 03083 #1 AWG Green

K22-4 03084 1/0 AWG Pink

K22-5 03085 2/0 AWG Black

K22-6 03086 3/0 AWG Orange

K22-7 03087 4/0 AWG Purple

K22-8 03088 250 Kcmil Yellow

K22-9 03089 300 Kcmil White

K22-10 03090 350 Kcmil Red

K22-11 03091 400 Kcmil Blue

K22-12 03092 500 Kcmil Brown

K22-13 03093 600 Kcmil Green

Connector Barrel Anderson Blackburn®Burndy Ilsco Panduit T&B Penn- No. of

Type Type Union Crimps*

Copper Short VHSS CPS YS-L CT SCSS/SCS 54504–54520 BCU A

Splice Long VHS CU YS CTL SCL/SCH 54804–54820 BBCU B

Short VHCS CTL-2/CTL YA-2LN/YA-L/YA-2L CRA/CRB LCAS/LCA 54104–54120 BLU A

Copper YA/YA-L-TC/YA-L-2TC LCD 54204–54218

Lugs Long VHCL CTL-L/LCN YA-2N CRA-L/CRB-L LCB/LCC 54930BE–54920BE BBLU B

CRA-2L/CRB-2L 54850BE–54878BE

EK22GL Battery-powered, High-speed CrimpingTool

Greenlee Textron / Subsidiary of Textron Inc. 94455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815/397-7070

Maintenance

Each Operating Day

Before use:

1. Inspect dies for wear or damage such as cracks,

gouges, or chips.

2. Inspect the tool for damage or leaks. If damage is

detected, return the tool to an authorized Greenlee

service center for inspection.

Skin injection hazard:

Do not use hands to check for oil

leaks. High pressure oil easily

punctures skin causing serious

injury, gangrene, or death. If injured,

seek medical help immediately to

remove oil.

Do not use solvents or flammable

cleaners to clean the tool body.

Solvents could ignite, causing

serious injury or property damage.

After use:

1. Wipe all tool surfaces clean with a damp cloth and

mild detergent.

2. Fully retract the ram. Place the tool in the carrying

case. Store in a cool, dry place.

3. Charge the battery.

Monthly

1. Thoroughly clean all surfaces.

2. Check the oil level.

3. Oil the bolt joints.

Annually or After 10,000 Crimps

1. Change the hydraulic oil.

2. Return the tool to an authorized Greenlee service

center for inspection.

Checking the Oil Level

1. Remove the two screws holding the tank housing

cover.

2. Remove the tank housing cover.

3. Point the cutting head towards the ground and

remove the oil plug. Add oil if necessary.

4. Replace the oil plug and the tank housing cover.

Secure with screws.

Recommended Hydraulic Oils

AVIA®HVI 15

Shell Tellus T 15

Mobil®DTE 11

NUTO®H 15

EK22GL Battery-powered, High-speed CrimpingTool

Greenlee Textron / Subsidiary of Textron Inc. 10 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815/397-7070

Troubleshooting

Before You Begin

1. Make sure that the battery is charged. Recheck the

battery after several minutes to make sure the

battery is holding its charge.

Tool is inoperative. Dirt, contaminants, etc., in ram area Clean tool.

of tool.

Crimping tool battery contacts Reform contacts.

damaged.

Tool components worn or damaged. Return tool to an authorized

Greenlee service center.

Dies stop during operation Oil level is low. Check oil level. Refill reservoir.

Air in hydraulic system. Pull trigger and hold retract button

simultaneously. Hold for approximately

10 seconds.

Battery load display flashes Battery charge low. Charge or replace battery.

constantly.

Tool loses oil. Damaged internal seal. Return tool to an authorized

Greenlee service center.

Oil plug not installed properly. Refill reservoir and replace plug.

2. Use a nonflammable contact cleaner or pencil

eraser to clean the electrical contacts on the battery

and crimping tool.

3. Reinstall the battery and check the tool again.

Probable CauseProblem Probable Remedy

Andere Handbücher für GATOR EK22GL

Inhaltsverzeichnis

Andere Greenlee Elektrowerkzeuge Handbücher

Greenlee

Greenlee GREENLEE KWIK-STRIPPER 45019 Bedienungsanleitung

Greenlee

Greenlee Fairmont F07 Bedienungsanleitung

Greenlee

Greenlee LPK1240 Bedienungsanleitung

Greenlee

Greenlee GATOR EK425L Bedienungsanleitung

Greenlee

Greenlee GATOR CK06FT Bedienungsanleitung

Greenlee

Greenlee CTR200 Bedienungsanleitung

Greenlee

Greenlee Quick Draw 7804SB Bedienungsanleitung

Greenlee

Greenlee RK1550 Bedienungsanleitung

Greenlee

Greenlee HPB45 Series Bedienungsanleitung

Greenlee

Greenlee CTR100 Bedienungsanleitung

Greenlee

Greenlee 1600 Series Bedienungsanleitung

Greenlee

Greenlee P2096 Bedienungsanleitung

Greenlee

Greenlee 750 Bedienungsanleitung

Greenlee

Greenlee GPU 18-8 Leitfaden

Greenlee

Greenlee E12CCXL Bedienungsanleitung

Greenlee

Greenlee Shear 30T Bedienungsanleitung

Greenlee

Greenlee LCS-144 Bedienungsanleitung

Greenlee

Greenlee F05 Bedienungsanleitung

Greenlee

Greenlee GATOR EK622L Bedienungsanleitung

Greenlee

Greenlee GATOR ESP710 Bedienungsanleitung

Greenlee

Greenlee GATOR CUAP32GL Bedienungsanleitung

Greenlee

Greenlee Quick Draw Series Bedienungsanleitung

Greenlee

Greenlee EK50ML Bedienungsanleitung

Greenlee

Greenlee Tugger 640 Leitfaden

Beliebte Elektrowerkzeuge Handbücher anderer Marken

AEG

AEG OMNI-JS Bedienungsanleitung

SIP

SIP 01533 Bedienungsanleitung

Ribimex

Ribimex PRS499 Bedienungsanleitung

3M Fiber Optic Connector Crimp Tool Bedienungsanleitung

Ryobi

Ryobi P524 Bedienungsanleitung

ROJEK

ROJEK FSN 300A Bedienungsanleitung

Kemper

Kemper 1740PRO Bedienungsanleitung

WABCO

WABCO OptiTire Bedienungsanleitung

EINHELL

EINHELL TE-MS 18/210 Li Bedienungsanleitung

Orgapack

Orgapack OR-T 85 Kurzanleitung

TOUGHCUT

TOUGHCUT Diamond 400 Bedienungsanleitung

Yaros

Yaros PB-3603 Bedienungsanleitung

Fein

Fein BSS 2.0 E Einrichtungshandbuch

Baileigh Industrial

Baileigh Industrial SS-2725 Bedienungsanleitung

Milwaukee

Milwaukee 2674-20 Bedienungsanleitung

Fein

Fein BLs 1.6 Bedienungsanleitung

Princess

Princess Electric Multi Sharpener Bedienungsanleitung

FOREDOM

FOREDOM K.1050 Handbuch