Greenlee G2090/03560 Bedienungsanleitung

INSTRUCTION MANUAL

MANUAL DE INSTRUCCIONES / MANUEL D’INSTRUCTIONS

Read and understand all of the instructions and safety information

in this manual before operating or servicing this tool.

G2090/03560

Adjustable Cable Stripping Tool

Español................. 7

Français.............. 13

www. .com information@itm.com1.800.561.8187

G2090/03560

Greenlee / A Textron Company

Table of Contents

Description .................................................................... 2

Safety ............................................................................ 2

Purpose of Manual ........................................................ 2

Important Safety Information ........................................ 3

Identication.................................................................. 4

Specications................................................................ 4

Maintenance.................................................................. 4

Operation....................................................................... 5

Blade Replacement....................................................... 6

Illustration and Parts List............................................. 18

Description

The Greenlee G2090/03560 Adjustable Cable Stripping

Tool is intended to remove the insulation from aluminum

and copper conductors.

Patent pending.

Safety

Safety is essential in the use and maintenance of

Greenlee tools and equipment. This instruction manual

and any markings on the tool provide information for

avoiding hazards and unsafe practices related to the

use of this tool. Observe all of the safety information

provided.

Purpose of this Manual

This manual is intended to familiarize all personnel with

the safe operation and maintenance procedures for the

following Greenlee tool:

G2090/03560 Adjustable Cable Stripping Tool

Keep this manual available to all personnel.

KEEP THIS MANUAL

All specications are nominal and may change as design

improvements occur. Greenlee Textron Inc. shall not be liable for

damages resulting from misapplication or misuse of its products.

www. .com information@itm.com1.800.561.8187

G2090/03560

Greenlee / A Textron Company

Identiﬁcation

Speciﬁcations

Capacity ........................................... 8 AWG to 750 kcmil

or cable with an outside diameter of

3/16" to 1-1/4" (4.7 mm to 31.7 mm)

1. Cable guide hook

2. Bi-directional blade

3. Blade depth adjustment knob

4. Handle

5. Handle stop

6. Thumb lever

7. Lifting edge

8. Directions for ring and spiral cutting

9. Directions for increasing and

decreasing blade depth

10. Blade housing

11. Blade housing latch (2)

Maintenance

Keep the tool clean and dry. No additional maintenance

is required.

www. .com information@itm.com1.800.561.8187

G2090/03560

Greenlee / A Textron Company

IMPORTANT SAFETY INFORMATION

SAFETY

ALERT

SYMBOL

This symbol is used to call your attention to hazards

or unsafe practices which could result in an injury or

property damage. The signal word, dened below,

indicates the severity of the hazard. The message

after the signal word provides information for pre-

venting or avoiding the hazard.

Immediate hazards which, if not avoided, WILL result

in severe injury or death.

Hazards which, if not avoided, COULD result in

severe injury or death.

Hazards or unsafe practices which, if not avoided,

MAY result in injury or property damage.

Read and understand all of the

instructions and safety information

in this manual before operating or

servicing this tool.

Failure to observe this warning could

result in severe injury or death.

This tool is not protected against

electrical shock. Read and under-

stand instructions before using the

Greenlee G2090/03560.

Failure to observe this warning could

result in severe injury or death.

Wear eye protection when using this

tool.

Failure to wear eye protection could

result in serious eye injury from ying

debris.

Blades are sharp. Keep ngers away

from blades when stripping cable and

when replacing blade.

Failure to observe this precaution

may result in injury.

www. .com information@itm.com1.800.561.8187

G2090/03560

Greenlee / A Textron Company

Operation

Numbers in parentheses refer to the “Identication”

section of this manual.

1. Rotate the blade depth adjustment knob (3) until the

blade (2) will strip the insulation without damaging

the conductor.

2. Place your hand around the handle (4) with your

index nger against the handle stop (5). Press the

lever (6) with your thumb to advance the cable guide

hook (1).

3. Place the cable stripping tool around the cable at

the location for the desired strip length.

4. Rotate the cable stripping tool two to three com-

plete revolutions around the cable in a counter-

clockwise direction to make the ring cut. The cutting

directions are displayed on the handle of the tool.

Ring Cutting Direction

Strip

Length

5. Rotate the cable stripping tool in the opposite direc-

tion around the cable to make a spiral cut to the end

of the cable. The cutting directions are displayed on

the handle of the stripping tool.

Spiral Cutting Direction

6. Remove the cable stripping tool from the cable.

7. Use the lifting edge (7) at the end of the spiral cut to

peel the insulation jacket off the conductor.

www. .com information@itm.com1.800.561.8187

G2090/03560

Greenlee / A Textron Company

Blade Replacement

Numbers in parentheses refer to the “Identication”

section of this manual.

A. Rotate the blade depth adjusting knob (3) until the

blade (2) is completely concealed.

B. Spread the two bottom tabs on the blade housing

(10) to disengage the two latches (11). The internal

compression spring will push the blade housing off

the handle.

C. Push the thumb lever (6) to advance the cable guide

hook (1) and remove the blade housing.

B. Spread bottom tabs to

remove blade housing.

Housing Latch

A. Rotate knob to conceal blade.

C. Press thumb lever to advance hook.

D. Remove the blade adjusting knob (3) and use pliers

to grab the top of the blade (2) and remove the

blade from the blade housing.

E. Align the at on the new blade with the at in the

blade housing.

E. Align ﬂat on

blade and housing.

F. Install the new blade until the blade base surface is

below the edge in the housing and approximately

0.025" below the housing surface.

0.025"

G. Reinstall the blade depth adjusting knob, but keep

the blade tip concealed for protection.

H. Reinstall the blade housing on the handle (4) until

both latches snap tight against the handle.

www. .com information@itm.com1.800.561.8187

G2090/03560

Illustration and Parts List

Key UPC No. Description Qty

1 Cable guide hook...................................................................................... 1

2 03961 Replacement blade................................................................................... 1

3 Blade adjusting knob ................................................................................ 1

4 Handle....................................................................................................... 1

10 Blade housing ........................................................................................... 1

12 Compression spring.................................................................................. 1

13 Sleeve ....................................................................................................... 1

14 05328 Plug........................................................................................................... 1

www. .com information@itm.com1.800.561.8187

Inhaltsverzeichnis

Andere Greenlee Werkzeuge Handbücher

Greenlee

Greenlee 52061455 Benutzerhandbuch

Greenlee

Greenlee ULTRA GLIDER UG5 Bedienungsanleitung

Greenlee

Greenlee EK1550FLT Bedienungsanleitung

Greenlee

Greenlee 709 Bedienungsanleitung

Greenlee

Greenlee 1800 Mechanical Bender Bedienungsanleitung

Greenlee

Greenlee K1GL Bedienungsanleitung

Greenlee

Greenlee K30GL Bedienungsanleitung

Greenlee

Greenlee 645-5/8 Bedienungsanleitung

Greenlee

Greenlee CR25 Bedienungsanleitung

Greenlee

Greenlee Ultra Tugger Bedienungsanleitung

Greenlee

Greenlee 1904Pg Bedienungsanleitung

Greenlee

Greenlee HKL1232 Bedienungsanleitung

Greenlee

Greenlee LS60L Bedienungsanleitung

Greenlee

Greenlee 45658 Bedienungsanleitung

Greenlee

Greenlee 713 Bedienungsanleitung

Greenlee

Greenlee K1GL Bedienungsanleitung

Greenlee

Greenlee 767 Bedienungsanleitung

Greenlee

Greenlee 660QA Bedienungsanleitung

Greenlee

Greenlee 881MBTS Bedienungsanleitung

Greenlee

Greenlee G1 Versi-Tugger Bedienungsanleitung

Greenlee

Greenlee JRF-4EPR Bedienungsanleitung

Beliebte Werkzeuge Handbücher anderer Marken

Martor

Martor SECUNORM 175 Bedienungsanleitung

ERKCO

ERKCO 1000 Bedienungsanleitung

jbc

jbc N4473 Bedienungsanleitung

FEINMETALL

FEINMETALL FZWZ-SET-001 Bedienungsanleitung

Worx Professional

Worx Professional Sonicrafter WU676 Bedienungsanleitung

Gage Bilt

Gage Bilt GB713SH Bedienungsanleitung

Hilti

Hilti DX 9-ENP Bedienungsanleitung

norbar

norbar NORTRONIC 34399 Bedienungsanleitung

BGS technic

BGS technic 8578 Bedienungsanleitung

Makita

Makita DHR241 Bedienungsanleitung

Motor Guard

Motor Guard JMB-1250 Bedienungsanleitung

Power Adhesives

Power Adhesives 805-12 Bedienungsanleitung

Clemco

Clemco 24189 Bedienungsanleitung

VVG

VVG VNG 903 Series Bedienungsanleitung

Hilti

Hilti FX 3-A Bedienungsanleitung

axing

axing BWZ 5-02 Bedienungsanleitung

Dh-Robotics

Dh-Robotics RGI-100 Anleitung zur Verwendung

Goobay

Goobay 97790 Bedienungsanleitung