Griffin Technology AP3299 Bedienungsanleitung
www.Griffin-Stands.com
Double Studio
Mixer Stand
www.Griffin-Stands.com
www.Griffin-Stands.com
Griffin™ stands and accessories are manufactured
in several innovative factories responsible for
developing products that address the newest
needs and trends of the current market. We take
pride in the Griffin™ brand and endeavor to be on
the forefront of the musical stands and musical
and lighting accessories market.
Performance Issue, Uneven or Unstable- Make
sure all nuts and bolts are tight on the product. If they
are, then loosen all nuts and bolts 1 full turn counter-
clockwise, then go back and tighten each bolt only ½
turn tight. Then do a final tighten turn for another ½
turn tight. Next, Make sure there are not any missing
nuts or bolts. Third, ensure all parts on the product
are not broken or defective. Finally, Re-read the
assembly instructions or watch the product
demonstration video to ensure you have correctly
assembled or are using the product properly with
factory specifications.
Missing Parts- The pictures, videos and images
shown in this manual might have changed style or
count due to the product being redesigned. So in rare
cases the part may no longer be included or of a
different style. However, if you think you are missing
a part that is necessary to the assembly and use of
your product, then first carefully double check all
packaging for any parts you think are missing. Some
parts might be hiding in the packaging or loose in an
inner box.
User Manual
M o d e l # A P 3 2 9 9
Griffin | 11408 Hwy 64 W, Tyler, TX 75704 |
Stands.com
For current product specifications, please to go
www.griffin-stands.com and type the model number
into the search bar. Locate the product listing to view
the current factory specifications. Thank you for purchasing the Griffin Double Studio
Mixer Stand. Your product comes with a 1 year
factory warranty from purchase date. Please read all
assembly instructions prior to assembling your new
cart. Pictures that may aid in assembly can be found
by going to www.griffin-stands.com and typing
AP3299 into the search bar.
Step 4 –Locate 2 pairs of
plates (Part D), take 1 and
place the plate with a screw
knob (Part E) on the bottom
of the crossbar and the other
one on the top parallel to the
plate at the bottom. Screw
the knob at the bottom to
secure the plates together as
shown on Figure 4.
Step 7 –For safety reasons,
please always make sure to
test the stability and safety of
the product before use.
Double check all nuts and
bolts, knobs and connectors,
make sure that these are tight
and securely fastened before
use of your product. Test the
product under light use or
light loads the first time to
confirm assembly and
structure of the product is
correct.
Step 1 –Locate the leg
assembly (Part A) and as seen
on Figure 1 expand and
unfold the legs of the stand.
The front legs can be spread
apart as far as needed. The
distance between the back
legs is determined by the back
crossbar.
Step 2 –To adjust the height
of the stand, each bottom of
the legs has a silver push pin
that is pushed to allow the
slots of the legs to adjust.
Pushing or pulling the bottom
part will be the height
adjustment, if the pin is on
the 3rd hole of one leg make
sure that all the other pins are
on the 3rd hole as well on the
other legs. Refer to Figure 2.
Step 5 –Take the arm (Part F
and H)and line the bottom
with the mount on the plates
you installed on Step 4. See
Figure 5. Tighten the knob to
secure the arm in place.
Step 6 –Figure 6 shows the knob (Part G) on the side of
the arm to adjust the angle and Figure 7 shows a knob
just below the arm to slide it front and back.
Please scan the QR Code below for the product
demonstration video. Or go to the URL shown here and find
the product video. www.Griffin-Stands.com/Videos
Step 3 –Place the
crossbar (Part B)
across the leg
assembly and line up
the nuts welded to
the crossbar with the
two holes closest to
the front of the stand
on each side (See
Figure 3)
Andere Griffin Technology Mischer Handbücher
