Grizzly G0442 Bedienungsanleitung

MODEL G0442

5 HP CYCLONE

WIRING UPDATE

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

#TR8040 PRINTED IN TAIWAN

We improved the remote controlled magnetic switch since the manual was originally printed. This sheet

shows the new magnetic switch assembly and the new wiring diagram. Keep this sheet with your Owner's

Manual in case you ever need to refer to it.

If you have questions, contact Tech Support at (570) 546-9663 or by email at [email protected].

ON/OFF

TIMER

2H 4H 8H

RUN POWEROVER

REMOTE CONTROL

SWITCH

220 VOLT

MAIN

SWITCH

The new switch features an overload device that

requires the cyclone to be restarted after it has

been overloaded. The new features of the switch

are described below:

POWER

This light is on when there is power to the

machine.

RUN

This light is on when the machine is running.

OVER

This light indicates that the machine has been

overloaded and it will not start again until it is reset

at the main switch.

To reset the machine from the overload state, turn

the main switch OFF, then ON.



























 





 

 



 





















 





G0442 5HP CYCLONE DUST COLLECTOR

G0442 New Switch and Wiring Diagram

Why did you get this kit?

This upgrade kit contains components that clean

the filter better and make the brush handles

easier to pull. In our ongoing efforts to provide

our customers with the best customer service in

the industry, we offer this upgrade free of charge.

While installation is optional, we do encourage

you to install this upgrade.

Upgrade Kit Contents

• Filter Brush ................................................. 1

• Square Pipe ................................................ 1

• Square Pipe Base ...................................... 1

• Stop Beads ................................................. 2

• Handle Covers ............................................ 2

• Handle Holder ............................................ 1

• Cable .......................................................... 1

• Filter Box Gasket ........................................ 1

• Filter Support Brace Gaskets ..................... 2

CYCLONE FILTER

UPGRADE KIT

INSTRUCTION SHEET

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

#TR7649 PRINTED IN TAIWAN

Getting Started

This procedure takes approximately 2 hours to

complete and requires you to provide the materi-

als listed below.

Materials Needed Qty

• Phillips Screwdriver .................................... 1

• Razor Blade or Paint Scraper .................... 1

• Wire Snips (optional) .................................. 1

• Socket or Wrench 12mm ............................ 1

• Socket or Wrench 11mm ............................ 1

• Socket or Wrench 10mm ............................ 1

• Clear Silicone .....................................Varies

• Rubbing Alcohol ................................. Varies

To install the upgrade kit components:

1. Unfasten the screws on the filter intake port.

2. Use a razor or putty knife to cut the silicone

around the filter intake port.

3. Cut the silicone around the black box.

4. Unfasten the screws under the black box,

and pry off the box plate.

5. Separate the intake port from the black box,

and completely clean off all remaining sili-

cone.

6. Pull or cut off the existing handle covers,

loosen the screw above the handles, and

remove the handles from the cable.

7. Unfasten the bolt at the top of the filter.

8. Unfasten the bolt at the bottom of the filter.

9. Remove the original brush handle holder.

11. Unfasten the screws at the bottom of the fil-

ter.

12. Remove the original brush.

13. Unfasten the screws from the original brush,

and throw away the old cable. (A new cable

is provided in the kit.)

10. Install the handle holder so it is directly below

the black box and about three squares from

the bottom of the filter.

15. Insert the new brush and base on the square

pipe. Make sure the pulley, brush screw, and

the holes at the top of the filter are aligned.

16. Fasten the square pipe base to the filter

frame.

17. Feed the new cable up through the brush,

over the pulley, and back down through the

brush, making sure the brush screw is facing

the pulley.

18. Feed both ends of the cable through the top

of the filter.

19. Feed the gasket over the cable and seat it

firmly on top of the filter.

14. Fasten the square pipe to the top of the fil-

ter.

20. Feed the cable over the pulleys in the black

box.

21. Fasten the black box to the top of the filter.

22. Feed the cable through the gasket and box

plate, then fasten the box plate to the black

box.

24. Pull the left side of the cable down until it

stops, and secure the stop bead up against

the handle holder.

23. Secure the stop bead on the right side of the

cable, approximately 12" from the end.

25. Loop the right side of the cable through a

handle, and pull the handle down to cinch the

cable tight.

26. Fasten the screw on the handle, and install

the other handle on the left side of the cable.

27. Insert the covers on the handles so the red

handle is on the right side and the black

handle is on the left side. (If you have difficul-

ties installing the covers, apply a little rubbing

alcohol on the handle to slide the covers on

easily. Allow the alcohol to dry before pulling

on the handles.)

28. Make sure that when the red handle is up the

filter brush is at the bottom of the filter.

29. Secure the brush to the right side cable by

tightening the screw on the brush clamp.

Brush Clamp

30. Fasten the filter intake with the screws.

31. Put silicone around the edges of the black

box and filter intake to seal them to the filter.

32. Use the two filter support gaskets between

the filter support braces and the filter when

reinstalling the filter on the cyclone.

Filter Support Brace Gasket

Andere Handbücher für G0442

Inhaltsverzeichnis

Andere Grizzly Staubabscheider Handbücher

Grizzly

Grizzly G1030 Bedienungsanleitung

Grizzly

Grizzly G0637 Bedienungsanleitung

Grizzly

Grizzly G1030 Bedienungsanleitung

Grizzly

Grizzly g0703 Bedienungsanleitung

Grizzly

Grizzly T10252 Bedienungsanleitung

Grizzly

Grizzly G0562Z Bedienungsanleitung

Grizzly

Grizzly G1837 Bedienungsanleitung

Grizzly

Grizzly G0818 Bedienungsanleitung

Grizzly

Grizzly G0583Z Bedienungsanleitung

Grizzly

Grizzly G0583 Bedienungsanleitung

Grizzly

Grizzly g0703 Bedienungsanleitung

Grizzly

Grizzly H8173 Bedienungsanleitung

Grizzly

Grizzly G0562 Bedienungsanleitung

Grizzly

Grizzly G0850 Bedienungsanleitung

Grizzly

Grizzly G0441 Bedienungsanleitung

Grizzly

Grizzly G1028Z Bedienungsanleitung

Grizzly

Grizzly G0860 Bedienungsanleitung

Grizzly

Grizzly G0443 Bedienungsanleitung

Grizzly

Grizzly G0785 Bedienungsanleitung

Grizzly

Grizzly G0703HEP Bedienungsanleitung

Grizzly

Grizzly G0637 Bedienungsanleitung

Grizzly

Grizzly H2935 Bedienungsanleitung

Grizzly

Grizzly T10117 Bedienungsanleitung

Grizzly

Grizzly G1029Z Bedienungsanleitung

Beliebte Staubabscheider Handbücher anderer Marken

Fein

Fein 9-88-35 Bedienungsanleitung

Blastrac

Blastrac BDC-44 Bedienungsanleitung

DIVERSITECH

DIVERSITECH WB-4000-D Handbuch

National

National 3402 Bedienungsanleitung

Bosch

Bosch GDE18V-16 Montageanleitung

Storch

Storch Cover Quick Wall Bedienungsanleitung

laguna

laguna C FLUX 1 Bedienungsanleitung

GMC

GMC RDC8LA Bedienungsanleitung

Jet

Jet DC-1100VX Series Service-Handbuch

Showa

Showa Fumeresa CBA-1000AT-HC-DSA-V1 Bedienungsanleitung

King Industrial

King Industrial KC-4043KWRC Bedienungsanleitung

Jet

Jet 500 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Super Dust Gorilla Bedienungsanleitung

Shop fox

Shop fox SHOP FOX W1687 Bedienungsanleitung

Blastrac

Blastrac 655DC Bedienungsanleitung

Elektra Beckum

Elektra Beckum Multi 180A Bedienungsanleitung

Jet

Jet DC-1100A Bedienungsanleitung

Woodtec

Woodtec XW043 Bedienungsanleitung