Grizzly T32713 Bedienungsanleitung

For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com

MODEL T32713

NEGATIVE PRESSURE GAUGE

KIT FOR G0860/G0861/G0862

DUST COLLECTORS

INSTRUCTIONS

NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

(FOR MODELS MFD. SINCE 08/21) #CS22017 PRINTED IN TAIWAN

Introduction

The Model T32713 Negative Pressure Gauge Kit

can be installed on the Model G0860, G0861, and

G0862 dust collectors to indicate when to clean or

replace the canister filter.

V1.08.21

To reduce your risk of

serious injury, read this

entire manual BEFORE

using machine.

Figure 1. Model T32713 Negative Pressure

Gauge Kit.

Box Contents (Figure 2) Qty

A. Pressure Gauge Assembly ......................... 1

B. Clear Tube 1⁄2" x 24" ................................... 1

C. Hose Clamps 1⁄2" ........................................ 2

D. 90º T-Fitting 1⁄2" x 11⁄2" x 11⁄2" ...................... 1

E. Dust Hose 11⁄2" x 43⁄4" ................................. 1

F. Hose Clamps 11⁄2" ...................................... 2

Inventory

ABC

D E F

NOTICE

If you cannot find an item on this list, care-

fully check around/inside the machine and

packaging materials. Often, these items get

lost in packaging materials while unpack-

ing or they are pre-installed at the factory.

Figure 2. Inventory.

Installation

Use the following steps to assemble the Model

T32713 and attach it to your Model G0860,

G0861, or G0862 dust collector.

Items Needed Qty

Wrenches or Sockets 10mm ............................ 2

Phillips Head Screwdriver #2 ............................ 1

Wear safety glasses during

the entire setup process!

-2- Model T32713 (Mfd. Since 08/21)

To install negative pressure gauge:

1. DISCONNECT DUST COLLECTOR FROM

POWER!

2. Place (2) 1⁄2" hose clamps around clear tube,

then slide one end of tube over port on back

of pressure gauge (see Figure 3).

4. Place (2) 11⁄2" hose clamps around dust

hose, then slide one end of hose over (1) 11⁄2"

port on T-fitting (see Figure 5).

5. Remove (2) flange nuts from hex bolts on

pressure gauge assembly (see Figure 6).

6. Spread jaws of pressure gauge mount just

enough to slide mount over support leg near

magnetic switch, as shown in Figure 6.

3. Slide other end of clear tube over 1⁄2" port on

T-fitting (see Figure 4).

Figure 4. Clear tube placed over T-fitting port.

Clear Tube

T-Fitting

1⁄2" Port

Figure 5. Dust hose placed over T-fitting port.

T-Fitting

Hose Clamp

Dust Hose

Figure 6. Pressure gauge mount placed on

support leg (G0861 shown).

Support Leg

Hex Bolt

(1 of 2)

Pressure

Gauge

Mount

Note: Position of pressure gauge mount

on support leg will differ from machine to

machine. Place mount near port on intake

barrel where pressure gauge will be visible

during operations.

Figure 3. Clear tube placed over pressure gauge

port.

Hose Clamp

Clear Tube

Pressure Gauge

Assembly

Model T32713 (Mfd. Since 08/21) -3-

7. Loosen hose clamp securing vacuum hose to

intake barrel port and remove hose from port

(see Figure 7).

8. Slide other end of dust hose from Step 4 over

intake barrel port (see Figure 8).

9. Slide vacuum hose over other port on T-fitting

(see Figure 8).

10. Adjust and orient hoses and clear tube as

needed to eliminate any kinks, then tighten

all (5) hose clamps to secure connections.

11. Slide pressure gauge mount to position where

it is easy to read, and secure in place with (2)

flange nuts removed in Step 5.

12. Connect dust collector to power.

Figure 7. Vacuum hose attached to intake barrel

port.

Vacuum

Hose

Intake Barrel

Port

Figure 8. Dust hose placed over intake barrel

port and vacuum hose over T-fitting port.

13. Cover intake dust ports and turn dust collec-

tor ON. Pressure gauge should indicate at

least 200mmAq or 2kPa.

— If gauge indicates at least 200mmAq or

2kPa, negative pressure kit has been

installed correctly and filter is operating

efficiently.

— If gauge indicates less than 200mmAq

or 2kPa, confirm all hose and tube con-

nections are tight and there are no kinks

that disrupt air flow. If gauge still indicates

less than 200mmAq, refer to Reading

Pressure Gauge to service filter as

required.

Reading Pressure Gauge

The Model G0860, G0861, and G0862 use a

handle and internal paddles to remove the dust

buildup from the filter. The negative pressure

gauge will help determine when a more thorough

cleaning is needed and whether the filter should

be replaced.

If the operating pressure on the pressure gauge

drops below 200mmAq or 2kPa (see Figure 9),

remove and clean the filter, as described in the

Owner's Manual.

If the operating pressure drops below 150mmAq

or 1.5kPa, and cleaning does not improve perfor-

mance, replace the filter.

Figure 9. Pressure gauge values.

Dust Hose

T-Fitting

Intake Barrel

Port

Vacuum Hose

-4- Model T32713 (Mfd. Since 08/21)

BUY PARTS ONLINE AT GRIZZLY.COM!

Scan QR code to visit our Parts Store.

T32713 Parts Breakdown & List

REF PART # DESCRIPTION REF PART # DESCRIPTION

1 PT32713001 PRESSURE GAUGE MOUNT 7 PT32713007 CLEAR TUBE 1/2" X 24"

2 PT32713002 T-FITTING 90-DEG 1/2" X 1-1/2" X 1-1/2" 8 PT32713008 BUTTON HD CAP SCR 1/4-20 X 1/2

3 PT32713003 NEGATIVE PRESSURE GAUGE 9 PT32713009 HOSE CLAMP 1-1/2"

4 PT32713004 HEX BOLT 1/4-20 X 2-1/2 10 PT32713010 DUST HOSE 1-1/2" X 4-3/4"

5 PT32713005 HOSE CLAMP 1/2" 11 PT32713011 FOAM 35 X 95 X 3MM

6 PT32713006 FLANGE NUT 1/4-20 12 PT32713012 TOUCH-UP PAI NT, GRI ZZLY GREEN

Please Note: We do our best to stock replacement parts whenever possible, but we cannot guarantee that all parts shown here

are available for purchase. Call (800) 523-4777 or visit our online parts store at www.grizzly.com to check for availability.

Andere Grizzly Staubabscheider Handbücher

Grizzly

Grizzly G0443 Kurzanleitung

Grizzly

Grizzly G1163 Bedienungsanleitung

Grizzly

Grizzly G1837 Bedienungsanleitung

Grizzly

Grizzly G0852 Bedienungsanleitung

Grizzly

Grizzly G0440 Technisches Handbuch

Grizzly

Grizzly G0601 Bedienungsanleitung

Grizzly

Grizzly G0703HEP Bedienungsanleitung

Grizzly

Grizzly G0562 Bedienungsanleitung

Grizzly

Grizzly G0601 Bedienungsanleitung

Grizzly

Grizzly G0548ZP Bedienungsanleitung

Grizzly

Grizzly G1028Z/G1029Z Bedienungsanleitung

Grizzly

Grizzly G0637 Kurzanleitung

Grizzly

Grizzly G0638 Kurzanleitung

Grizzly

Grizzly G0443HEP Bedienungsanleitung

Grizzly

Grizzly T28798 Bedienungsanleitung

Grizzly

Grizzly H8173 Bedienungsanleitung

Grizzly

Grizzly G0637HEP Bedienungsanleitung

Grizzly

Grizzly G0440 Bedienungsanleitung

Grizzly

Grizzly G1032 Bedienungsanleitung

Grizzly

Grizzly G0441HEP Bedienungsanleitung

Grizzly

Grizzly G0562 Bedienungsanleitung

Grizzly

Grizzly G0548 Bedienungsanleitung

Grizzly

Grizzly Extreme Series Bedienungsanleitung

Grizzly

Grizzly G0443 Bedienungsanleitung

Beliebte Staubabscheider Handbücher anderer Marken

Fein

Fein 9-88-35 Bedienungsanleitung

Blastrac

Blastrac BDC-44 Bedienungsanleitung

DIVERSITECH

DIVERSITECH WB-4000-D Handbuch

National

National 3402 Bedienungsanleitung

Bosch

Bosch GDE18V-16 Montageanleitung

Storch

Storch Cover Quick Wall Bedienungsanleitung

laguna

laguna C FLUX 1 Bedienungsanleitung

GMC

GMC RDC8LA Bedienungsanleitung

Jet

Jet DC-1100VX Series Service-Handbuch

Showa

Showa Fumeresa CBA-1000AT-HC-DSA-V1 Bedienungsanleitung

King Industrial

King Industrial KC-4043KWRC Bedienungsanleitung

Jet

Jet 500 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Super Dust Gorilla Bedienungsanleitung

Shop fox

Shop fox SHOP FOX W1687 Bedienungsanleitung

Blastrac

Blastrac 655DC Bedienungsanleitung

Elektra Beckum

Elektra Beckum Multi 180A Bedienungsanleitung

Jet

Jet DC-1100A Bedienungsanleitung

Woodtec

Woodtec XW043 Bedienungsanleitung