Grizzly T32841 Bedienungsanleitung

NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

(FOR MODELS MFD. SINCE 11/21) #CS22154 PRINTED IN TAIWAN V1.11.21

Introduction

The Model T32841 Sliding Log Milling Sled rip

cuts logs at least 173⁄4" long and up to 113⁄4"

in diameter on vertical wood-cutting bandsaws

when used with the T32838 Bandsaw Sled.

Inventory

Figure 1. T32841 inventory.

Description Qty

A. Milling Sled ................................................. 1

B. Hold-Down Weights .................................... 2

C. Knobs 3⁄8"-16 ............................................... 2

D. Hinge Rods................................................. 2

E. Open-End Wrenches 13mm ....................... 2

F. Hex Bolts M8-1.25 x 55 .............................. 2

G. Lock Nuts M8-1.25 ..................................... 2

H. Claw Hold-Downs ....................................... 2

NOTICE

If you cannot find item on list, check around/

inside packaging materials. Often, items

get lost in packaging while unpacking or

they are pre-installed at factory.

FGH

Assembly

Wear safety glasses during

the entire setup process!

The Model T32841 must be assembled before it

can be mounted on the bandsaw sled.

To assemble milling sled:

1. Attach (2) hinge rods to milling sled with (2)

M8-1.25 x 55 hex bolts and M8-1.25 lock

nuts, as shown in Figure 2.

Figure 2. Attaching hinge rods to milling sled.

x 2

Hinge

Rods

Milling

Sled

For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com

MODEL T32841

SLIDING LOG MILLING

SLED

INSTRUCTIONS

-2- Model T32841 (Mfd. Since 11/21)

Using Milling Sled

Items Needed Qty

Vertical Bandsaw ............................................... 1

T32838 Bandsaw Sled ...................................... 1

To reduce risk of eye injury from flying

chips or lung damage from breathing dust,

always wear safety glasses and a respirator

when operating bandsaw.

Mount the Model T32841 on the tracks of the

T32838 Bandsaw Sled to smoothly feed logs

across the table of your bandsaw.

IMPORTANT: Refer to the bandsaw manual for

information on safely operating your bandsaw.

To use milling sled:

1. Refer to Model T32838 Instructions to

install bandsaw sled on bandsaw.

2. DISCONNECT BANDSAW FROM POWER!

3. Align tracks of milling sled with tracks of

bandsaw sled, then slide milling sled onto

bandsaw sled (see Figure 3).

4. Rest workpiece on milling sled, aligning blade

with intended line of cut (see Figure 4).

5. Secure workpiece with claw hold-downs by

inserting them into slots in milling sled (see

Figure 4).

Note: Hinge rods should extend up through

holes in claw hold-downs (see Figure 4).

Figure 4. Workpiece and claw hold-downs

installed.

Workpiece

Slot

Note: If workpiece is too tall to be secured by

slots, remove (4) hex nuts and button head

cap screws shown in Figure 5, extend milling

sled height with frame extension, then secure

with hex nuts and button head cap screws.

x 4

Frame Extension

Figure 5. Example of milling sled extended.

Figure 3. Sliding milling sled onto bandsaw sled.

Tracks

Milling

Sled

Bandsaw

Sled

Claw Hold-Down

(1 of 2)

Model T32841 (Mfd. Since 11/21) -3-

6. Install (2) hold-down weights onto hinge

rods, fitting weights into hollows in claw hold-

downs (see Figure 6).

Note: Install weights in hollows that best

secure workpiece (see Figure 6).

Figure 6. Hold-down weights installed.

7. Thread (2) 3⁄8"-16 knobs onto hinge rods

and tighten against hold-down weight (see

Figure 7).

Figure 7. Knobs threaded onto hinge rods.

Hinge Rod

(1 of 2)

Hold-Down

Hollow

Hold-Down

Weight

(1 of 2)

Hinge Rod

(1 of 2)

Knob

(1 of 2)

Hold-Down

Weight

(1 of 2)

9. Lift bandsaw sled handle (see Figure 8) and

adjust sled right so workpiece is out of blade

path.

Figure 8. Location of pointer on rail and

bandsaw sled handle.

Bandsaw Sled

Handle

8. Make note of where pointer points on bandsaw

sled rail (see Figure 8).

Pointer

10. Move bandsaw sled handle down to lock

position.

11. Push workpiece forward through a test cut.

Workpiece must clear blade before any por-

tion of milling table extends off of bandsaw

sled rear.

12. Adjust sled back to measurement noted in

Step 8 and secure it in place for cut.

13. Connect bandsaw to power, turn bandsaw

ON, then slide table forward on sled to feed

workpiece through blade and complete cut.

If workpiece is too long to cut without milling

sled leaving bandsaw sled, milling sled and

workpiece can easily tip off of bandsaw

sled. Body parts could be pulled into moving

blade or pinched/crushed if caught under

falling workpiece. Use roller table (or other

method of workpiece support) or cut down

workpiece to more manageable length.

-4- Model T32841 (Mfd. Since 11/21)

BUY PARTS ONLINE AT GRIZZLY.COM !

Scan QR code to visit our Parts Store.

T32841 Parts Breakdown & List

Please Note: We do our best to stock replacement parts whenever possible, but we cannot guarantee that all parts shown here

are available for purchase. Call (800) 523-4777 or visit our online parts store at www.grizzly.com to check for availability.

REF PART # DESCRIPTION REF PART # DESCRIPTION

1 PT32841001 MI LLI NG FRAME 7 PT32841007 KNOB 3/8-16, 5-LOBE, D2

2 PT32841002 CLAW HOLD-DOWN 8 PT32841008 TRACK

3 PT32841003 HINGE ROD 3/8-16 X 9-7/8 9 PT32841009 HEX BOLT M8-1.25 X 55

4 PT32841004 WRENCH 13MM OPEN-END 10 PT32841010 LOCK NUT M8-1.25

5 PT32841005 HOLD-DOWN WEI GHT 11 PT32841011 BUTTON HD CAP SCR M5-.8 X 10

6 PT32841006 FRAME EXTENSION 12 PT32841012 HEX NUT M5-. 8

Andere Grizzly Industrieanlagen Handbücher

Grizzly

Grizzly G9933 Bedienungsanleitung

Grizzly

Grizzly G0877 Bedienungsanleitung

Grizzly

Grizzly G0708 Bedienungsanleitung

Grizzly

Grizzly G0707 Bedienungsanleitung

Grizzly

Grizzly G0714 Bedienungsanleitung

Grizzly

Grizzly G0876 Bedienungsanleitung

Grizzly

Grizzly G0931L Bedienungsanleitung

Grizzly

Grizzly T32840 Bedienungsanleitung

Grizzly

Grizzly G0656P Bedienungsanleitung

Grizzly

Grizzly T20798 Bedienungsanleitung

Grizzly

Grizzly G0718 Bedienungsanleitung

Grizzly

Grizzly T10460 Bedienungsanleitung

Grizzly

Grizzly G0792 Bedienungsanleitung

Grizzly

Grizzly T31850 Bedienungsanleitung

Grizzly

Grizzly T33447 Bedienungsanleitung

Grizzly

Grizzly G0479 Bedienungsanleitung

Grizzly

Grizzly G0738 Bedienungsanleitung

Grizzly

Grizzly H7590 Bedienungsanleitung

Grizzly

Grizzly T33850 Bedienungsanleitung

Grizzly

Grizzly T28173 Bedienungsanleitung

Grizzly

Grizzly T32428 Bedienungsanleitung

Grizzly

Grizzly T32537 Bedienungsanleitung

Grizzly

Grizzly T32839 Bedienungsanleitung

Grizzly

Grizzly G0731 Bedienungsanleitung

Beliebte Industrieanlagen Handbücher anderer Marken

ABB

ABB Unifix AD Handbuch

Mark 7

Mark 7 Evolution Bedienungsanleitung

Husky

Husky HyPET Bedienungsanleitung

bora

bora PM-1800 Bedienungsanleitung

Siemens

Siemens 8MF1 Series Bedienungsanleitung

ABB

ABB HT610965 Bedienungsanleitung

ABB

ABB SafeLink Bedienungsanleitung

Phoenix

Phoenix PHX-150 Bedienungsanleitung

ABB

ABB A165-L32 Bedienungsanleitung

ABB

ABB HT842936 Bedienungsanleitung

Hermetica

Hermetica 10 Series Bedienungsanleitung

HORNER

HORNER OEE Solution Bedienungsanleitung

Hammerhead

Hammerhead HG375 Bedienungsanleitung

SCHUNK

SCHUNK VERO-S NSE-A3 138 Gebrauchsanweisung

ABB

ABB HT566657 Bedienungsanleitung

Webasto

Webasto GSE CAN Bedienungsanleitung

ABB

ABB HT614003 Bedienungsanleitung

BAC

BAC BCP2D Bedienungsanleitung