Grizzly G0555 Bedienungsanleitung

Model G0555

Extension Block Kit

Grizzly’s Model H3051 Extension Block Kit

(shown in Figure 1) increases the cutting height

of the Model G0555 Bandsaw to 12".

To install the Extension Block Kit:

1. Disconnect the bandsaw from the power

source!

2. Open the wheel covers and remove the

blade per manual instructions.

3. Remove the left-side blade guard (Figure 2).

4. Remove the power switch assembly (Figure

2). DO NOT disconnect the wiring and wait

until Step 12 to remove the guide post

assembly.

5. Have an assistant support the upper arm

assembly (Figure 3), then loosen the nut and

slide the bolt out. Remove the upper arm and

set it aside. Note—The upper arm is pinned

to the base. If removal is difficult, carefully

rock it loose.

6. Place the extension block onto the base pins.

7. Have an assistant place the upper arm onto

the extension block pins and hold it in place

(Figure 4).

8. Place a washer over the long extension bolt

and slide the bolt down through the exten-

sion block.

Figure 1. Extension Block Kit.

Figure 2. Power switch and left side blade

guard.

Figure 3. Loosening bolt while an assistant sup-

ports the upper arm assembly.

Disconnect power to the

machine when perform-

ing any maintenance or

assembly. Failure to do

this may result in serious

personal injury.

Power

Switch

Left-side

Blade

Guard

9. Attach the washer and the nut to the exten-

sion bolt, and tighten the bolt until secure.

10. Install the extended left-side blade guard.

11. Remove the guide assembly and the blade

guard from the original guide post.

12. To keep the small parts from falling out,

install the extension guide post from the top

of the guide post bracket by loosening the

original guide post and lowering it as you

guide the new post into place.

13. Attach the guide assembly and the extended

blade guard to the new guide post.

14. Install the 105" bandsaw blade, tension it

properly, test the tracking, and adjust the

blade guides per the manual instructions.

15. Check the alignment of the bandsaw wheels

according to the manual and align if neces-

sary.

16. Replace the power switch assembly. Note—

It can be placed in the original holes, or in

holes drilled into the new extension block.

If you need additional help with this procedure,

call our service department at: (570) 546-9663.

Figure 4. Placing upper arm on extension block.

Figure 5. Extension block components.

Figure 6. G0555 Bandsaw with extension block

installed.

New

Left-side

Guard

Extended

Guard

Extended

Guide

Post

Andere Handbücher für G0555

Inhaltsverzeichnis

Andere Grizzly Zubehör für Elektrowerkzeuge Handbücher

Grizzly

Grizzly T32058 Bedienungsanleitung

Grizzly

Grizzly T10808 Bedienungsanleitung

Grizzly

Grizzly H7585 Bedienungsanleitung

Grizzly

Grizzly H6264 Bedienungsanleitung

Grizzly

Grizzly G5749 Bedienungsanleitung

Grizzly

Grizzly T10125 Bedienungsanleitung

Grizzly

Grizzly G1083 Bedienungsanleitung

Grizzly

Grizzly T31496 Bedienungsanleitung

Grizzly

Grizzly H6238 Bedienungsanleitung

Grizzly

Grizzly T32734 Bedienungsanleitung

Grizzly

Grizzly H5664 Bedienungsanleitung

Grizzly

Grizzly G4026 Bedienungsanleitung

Beliebte Zubehör für Elektrowerkzeuge Handbücher anderer Marken

Bosch

Bosch OSC004 Bedienungsanleitung

Rockler

Rockler 57510 Bedienungsanleitung

Bosch

Bosch RA1054 Montageanleitung

Kitagawa

Kitagawa SC N Series Bedienungsanleitung

Wolfcraft

Wolfcraft FKS 145 Kurzanleitung

ADAMAS

ADAMAS B32 Bedienungsanleitung

STEINEL PROFESSIONAL

STEINEL PROFESSIONAL 4007841009595 Bedienungsanleitung

Echo

Echo Speed-Feed Universal 400 LH/RH Bedienungsanleitung

SCHUNK

SCHUNK ROTA TB-TBS-EP Gebrauchsanweisung

Schmid

Schmid RAPID Secure XL Bedienungsanleitung

Drill Master

Drill Master 360X Bedienungsanleitung

Toro

Toro 138-5050 Bedienungsanleitung

jbc

jbc SF-SD Bedienungsanleitung

Bosch

Bosch GTA 3800 Professional Montageanleitung

RG AVAK

RG AVAK MaxDrill Series Bedienungsanleitung

infaco

infaco PW3 Bedienungsanleitung

Gloria

Gloria CUT & BRUSH Bedienungsanleitung

Bench Dogs

Bench Dogs Quad MFT Hinge System Bedienungsanleitung