Grizzly G5344 Bedienungsanleitung

Introduction

This 15,000 RPM air sander requires 75 PSI and

3" x 41/2" sanding sheets. (You can cut a standard

9" x 11" sanding sheet into sixths and trim each

piece to size.) Air hose inlet is 1/4" NPT.

Inventory

A. Air Palm Sander ......................................... 1

B. Air Hose ...................................................... 1

MODEL G5344

AIR PALM SANDER

INSTRUCTION SHEET

Figure 2. Opening clamp.

Figure 1. Model G5344.

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

#BL8253 PRINTED IN TAIWAN

Assembly and Attaching Abrasives

To assemble the sander and attach sandpa-

per:

1. Thread the air hose into the sander.

2. Install a 1⁄4" NPT male quick-disconnect fitting

(not included) into the end of the hose.

3. Lift one clamp up over the bracket (Figure 2),

then pull the clamp down to open it.

4. Insert one end of the sandpaper between the

clamp and base as shown in Figure 3, and

lift the clamp up and back over the bracket to

secure the sandpaper.

Figure 3. Attaching and securing sanding sheet.

Bracket

EYE INJURY HAZARD!

Always wear safety glasses

when using this tool to

prevent serious personal

injury.

INJURY HAZARD!

Always disconnect tool from

air to prevent unexpected

operation during service.

DUST HAZARD!

Always wear respirator when

using this tool.

5. Repeat Step 3 with the opposite clamp, fold

the sandpaper over the sander, and repeat

Step 4, making sure the paper fits snugly as

shown in Figure 4.

Figure 4. Attaching sandpaper on opposite side.

Operation

To operate the sander:

1. Connect the tool to compressed air.

2. Hold the sander and push the throttle valve

(Figure 5) inwards to turn the sander on.

Figure 6. Lubricating directly into air fitting.

Maintenance

Lubricate at the beginning of the sanding task.

Place one or two drops of pneumatic tool oil

directly into the air fitting as shown in Figure 6.

Figure 5. Sander controls.

Throttle

Valve

3. Push or pull the throttle valve (Figure 5)

between ON and OFF to control the speed of

the sander.

A filter/lubricator/regulator set up is not recom-

mended, as excess oil in the tool could spray onto

the workpiece.

Run the sander for a few minutes to eject excess

oil, then wipe the tool down with a rag and begin

sanding. Oil the tool after use or storage.

If you need help with your new pneumatic tool, call

our Tech Support at: (570) 546-9663.

4. Pull the throttle valve outwards to stop the

sander.

5. When the sandpaper loses its effectiveness,

disconnect the sander from air, remove

sandpaper from the clamps, and replace with

a new sheet.

G5344 Parts Breakdown and List



















































REF PART # DESCRIPTION REF PART # DESCRIPTION

1 PS07M PHLP HD SCR M4-.7 X 8 14 P5344014 CYLINDER

2 PLW02M LOCK WASHER 4MM 15 P5344015 STEEL BALL

3 P5344003 HOUSING COVER 16 P5344016 CLAMP SPRING

4 P5344004 RUBBER SUPPORT ASSEMBLY 17 P5344017 FLAT HEAD SCREW

5 P5344005 TUBE ASSEMBLY 18 P5344018 CYLINDER SUB ASSEMBLY

6 P5344006 MODEL LABEL 19 PFH49M FLAT HD SCR M3-.5 X 6

7 P5344007 RUBBER PAD ASSEMBLY 20 P5344020 VALVE BUSHING

8 P5344008 THROTTLE VALVE 21 P5344021 FLAT HEAD SCREW

9 P5344009 O-RING 22 PLW02M LOCK WASHER 4MM

10 P5344010 VALVE FITTING 23 P5344023 HOSE SUB ASSEMBLY

11 P5344011 HOUSING CAP 24 P5344024 CLAMP STOMPER

12 PS38M PHLP HD SCR M4-.7 X 10 25 P5344025 ROLL PIN

13 P5344013 END PLATE

Andere Grizzly Sander Handbücher

Grizzly

Grizzly G9984 Bedienungsanleitung

Grizzly

Grizzly G5970 Bedienungsanleitung

Grizzly

Grizzly H3120 Leitfaden

Grizzly

Grizzly G0920 Bedienungsanleitung

Grizzly

Grizzly G0571 Bedienungsanleitung

Grizzly

Grizzly H2881 Bedienungsanleitung

Grizzly

Grizzly G5970 Kurzanleitung

Grizzly

Grizzly G9922 Bedienungsanleitung

Grizzly

Grizzly G0574 Bedienungsanleitung

Grizzly

Grizzly G0538 Kurzanleitung

Grizzly

Grizzly H0584 Kurzanleitung

Grizzly

Grizzly G1014Z Bedienungsanleitung

Grizzly

Grizzly T32003 Bedienungsanleitung

Grizzly

Grizzly G1015 Bedienungsanleitung

Grizzly

Grizzly G0474 Kurzanleitung

Grizzly

Grizzly G0538 Bedienungsanleitung

Grizzly

Grizzly H7760 Kurzanleitung

Grizzly

Grizzly H2882 Bedienungsanleitung

Grizzly

Grizzly G0644 Bedienungsanleitung

Grizzly

Grizzly T26417 Bedienungsanleitung

Grizzly

Grizzly G0864 Bedienungsanleitung

Grizzly

Grizzly H3120 Bedienungsanleitung

Grizzly

Grizzly G1071 Bedienungsanleitung

Grizzly

Grizzly G3105 Bedienungsanleitung

Beliebte Sander Handbücher anderer Marken

Oliver

Oliver 6305 Bedienungsanleitung

Jet

Jet 22-44 Pro-3 Service-Handbuch

Makita

Makita M9204 Handbuch

Makita

Makita M9204 Bedienungsanleitung

Craftsman

Craftsman 351.215131 Bedienungsanleitung

Clarke

Clarke Woodworker CBS1-5B Bedienungsanleitung

Chicago Pneumatic

Chicago Pneumatic CP9778 Bedienungsanleitung

Nitto Kohki

Nitto Kohki BB-20 Bedienungsanleitung

Ferm

Ferm FEOS-135 Bedienungsanleitung

Unior

Unior 1510 Bedienungsanleitung

stayer

stayer ls1200 Bedienungsanleitung

Jet

Jet JSG-96 Service-Handbuch

Parkside

Parkside PDS 290 B2 Bedienungsanleitung

Status

Status XPA Series Bedienungsanleitung

Clarke

Clarke EZ Sand Bedienungsanleitung

Craftsman

Craftsman 113.22521 Bedienungsanleitung

Craftsman

Craftsman 113.225831 Bedienungsanleitung

CLAS

CLAS OP 1429 Bedienungsanleitung